This is the first official Postfix release that is not called BETA. May it help the people who cannot get BETA software past their management. Release 20010228 differs from snapshot 20010228 in that the virtual delivery agent and nqmgr queue manager are left out. That software will become part of the official release when it has not changed in a while. In the text below, incompatible changes are labeled with the Postfix version that introduced the change. If you upgrade from a later Postfix version, then you do not have to worry about that particular incompatibility. Major incompatible changes with release-20010228 ================================================ [snapshot-20010225] POSTFIX NO LONGER RELAYS MAIL FOR CLIENTS IN THE ENTIRE CLASS A/B/C NETWORK. To get the old behavior, specify "mynetworks_style = class" in the main.cf file. The default (mynetworks_style = subnet) is to relay for clients in the local IP subnet. See conf/main.cf. [snapshot-20001005, snapshot-20010225] You must execute "postfix stop" before installing this release. Some recommended parameter settings have changed, and a new entry must be added to the master.cf file before you can start Postfix again. 1 - The recommended Postfix configuration no longer uses flat directories for the "incoming" "active", "bounce", and "defer" queue directories. The "flush" directory for the new "flush" service directory should not be flat either. Upon start-up, Postfix checks if the hash_queue_names configuration parameter is properly set up, and will add any queue directory names that are missing. 2 - In order to improve performance of one-to-one mail deliveries the queue manager will now look at up to 10000 queue files (was: 1000). The default qmgr_message_active_limit setting was changed accordingly. If you have a non-default qmgr_message_active_limit in main.cf, you may want adjust it. 3 - The new "flush" service needs to be configured in master.cf. Upon start-up, Postfix checks if the new "flush" service is configured in the master.cf file, and will add an entry if it is missing. Should you wish to back out to a previous Postfix release there is no need to undo the above queue configuration changes. [snapshot-20000921] The protocol between queue manager and delivery agents has changed. This means that you cannot mix the Postfix queue manager or delivery agents with those of Postfix versions prior to 20000921. This change does not affect Postfix queue file formats. [snapshot-20000529] This release introduces an incompatible queue file format change ONLY when content filtering is enabled (see text in FILTER_README). Old Postfix queue files will work fine, but queue files with the new content filtering info will not work with Postfix versions before 20000529. Postfix logs a warning and moves incompatible queue files to the "corrupt" mail queue subdirectory. Minor incompatible changes with release-20010228 ================================================ [snapshot-20010225] The incoming and deferred queue directories are now hashed by default. This improves the performance considerably under heavy load, at the cost of a small but noticeable slowdown when one runs "mailq" on an unloaded system. [snapshot-20010222] Postfix no longer automatically delivers recipients one at a time when their domain is listed in $mydestination. This change solves delivery performance problems with delivery via LMTP, with virus scanning, and with firewall relays that forward all mail for $mydestination to an inside host. The "one recipient at a time" delivery behavior is now controlled by the per-transport recipient limit (xxx_destination_recipient_limit, where xxx is the name of the delivery mechanism). This parameter controls the number of recipients that can be sent in one delivery (surprise). The setting of the per-transport recipient limit also controls the meaning of the per-transport destination concurrency limit (named xxx_destination_concurrency_limit, where xxx is again the name of the delivery mechanism): 1) When the per-transport recipient limit is 1 (i.e., send one recipient per delivery), the per-transport destination concurrency limit controls the number of simultaneous deliveries to the same recipient. This is the default behavior for delivery via the Postfix local delivery agent. 2) When the per-transport recipient limit is > 1 (i.e., send multiple recipients per delivery), the per-transport destination concurrency limit controls the number of simultaneous deliveries to the same domain. This is the default behavior for all other Postfix delivery agents. [snapshot-20010128] The Postfix local delivery agent now enforces mailbox file size limits (default: mailbox_size_limit = 51200000). This limit affects all file write access by the local delivery agent or by a process run by the local delivery agent. The purpose of this parameter is to act as a safety for run-away software. It cannot be a substitute for a file quota management system. Specify a limit of 0 to disable. [snapshot-20010128] REJECT in header/body_checks is now flagged as policy violation rather than bounce, for consistency in postmaster notifications. [snapshot-20010128] The default RBL (real-time blackhole lists) domain examples have been changed from *.vix.com to *.mail-abuse.org. [snapshot-20001210] Several interfaces of libutil and libglobal routines have changed. This may break third-party code written for Postfix. In particular, the safe_open() routine has changed, the way the preferred locking method is specified in the sys_defs.h file, as well as all routines that perform file locking. When compiling third-party code written for Postfix, the incompatibilities will be detected by the compiler provided that #include file dependencies are properly maintained. [snapshot-20001210] When delivering to /file/name (as directed in an alias or .forward file), the local delivery agent now logs a warning when it is unable to create a /file/name.lock file. Mail is still delivered as before. [snapshot-20001210] The "sun_mailtool_compatibility" feature is going away (a compatibility mode that turns off kernel locks on mailbox files). It still works, but a warning is logged. Instead of using "sun_mailtool_compatibility", specify the mailbox locking strategy as "mailbox_delivery_lock = dotlock". [snapshot-20001210] The Postfix SMTP client now skips SMTP server replies that do not start with "CODE SPACE" or with "CODE HYPHEN" and flags them as protocol errors. Older Postfix SMTP clients silently treated "CODE TEXT" as "CODE SPACE TEXT", i.e. as a valid SMTP reply. [snapshot-20001121] On RedHat Linux 7.0, you must install the db3-devel RPM before you can compile the Postfix source code. [snapshot-20000924] The postmaster address in the "sorry" text at the top of bounced mail is now just postmaster, not postmaster@machine. The idea is to refer users to their own postmaster. [snapshot-20000921] The notation of [host:port] in transport tables etc. is going away but it is still supported. The preferred form is now [host]:port. This change is necessary to support IPV6 address forms which use ":" as part of a numeric IP address. In a future release, Postfix will log a warning when it encounters the [host:port] form. [snapshot-20000921] In mail headers, Errors-To:, Reply-To: and Return-Receipt: addresses are now rewritten as a sender address (was: recipient). [snapshot-20000921] Postfix no longer inserts Sender: message headers. [snapshot-20000921] The queue manager now logs the original number of recipients when opening a queue file (example: from=<>, size=3502, nrcpt=1). [snapshot-20000921] The local delivery agent no longer appends a blank line to mail that is delivered to external command. [snapshot-20000921] The pipe delivery agent no longer appends a blank line when the F flag is specified (in the master.cf file). Specify the B flag if you need that blank line. [snapshot-20000507] As required by RFC 822, Postfix now inserts a generic destination message header when no destination header is present. The text is specified via the undisclosed_recipients_header configuration parameter (default: "To: undisclosed-recipients:;"). [snapshot-20000507] The Postfix sendmail command treats a line with only `.' as the end of input, for the sake of sendmail compatibility. To disable this feature, specify the sendmail-compatible `-i' or `-oi' flags on the sendmail command line. [snapshot-20000507] For the sake of Sendmail compatibility, the Postfix SMTP client skips over SMTP servers that greet with a 4XX or 5XX reply code, treating them as unreachable servers. To obtain prior behavior (4XX=retry, 5XX=bounce), specify "smtp_skip_4xx_greeting = no" and "smtp_skip_5xx_greeting = no". Major changes with release-20010228 =================================== Postfix produces DSN formatted bounced/delayed mail notifications. The human-readable text still exists, so that users will not have to be unnecessarily confused by all the ugliness of RFC 1894. Full DSN support will be later. This release introduces full content filtering through an external process. This involves an incompatible change in queue file format. Mail is delivered to content filtering software via an existing mail delivery agent, and is re-injected into Postfix via an existing mail submission agent. See examples in the FILTER_README file. Depending on how the filter is implemented, you can expect to lose a factor of 2 to 4 in delivery performance of SMTP transit mail, more if the content filtering software needs lots of CPU or memory. Specify "body_checks = regexp:/etc/postfix/body_checks" for a quick and dirty emergency content filter that looks at non-header lines one line at a time (including MIME headers inside the message body). Details in conf/sample-filter.cf. The header_checks and body_checks features can be used to strip out unwanted data. Specify IGNORE on the right-hand side and the data will disappear from the mail. Support for SASL (RFC 2554) authentication in the SMTP server and in the SMTP and LMTP clients. See the SASL_README file for more details. This file still needs better examples. Postfix now ships with an LMTP delivery agent that can deliver over local/remote TCP sockets and over local UNIX-domain sockets. The LMTP_README file gives example, but still needs to be revised. Fast "ETRN" and "sendmail -qR". Postfix maintains per-destination logfiles with information about what mail is queued for selected destinations. See the file ETRN_README for details. The mailbox locking style is now fully configurable at runtime. The new configuration parameter is called "mailbox_delivery_lock". Depending on the operating system type, mailboxes can be locked with one or more of "flock", "fcntl" or "dotlock". The command "postconf -l" shows the available locking styles. The default mailbox locking style is system dependent. This change affects all mailbox and all "/file/name" deliveries by the Postfix local delivery agent. Minor changes with release-20010228 =================================== You can now specify multiple SMTP destinations in the relayhost and fallback_relay configuration parameters. The destinations are tried in the specified order. Specify host or host:port (perform MX record lookups), [host] or [host]:port (no MX record lookups), [address] or [address]:port (numerical IP address). The "mailbox_transport" and "fallback_transport" parameters now understand the form "transport:nexthop", with suitable defaults when either transport or nexthop are omitted, just like in the Postfix transport map. This allows you to specify for example, "mailbox_transport = lmtp:unix:/file/name". The local_transport and default_transport configuration parameters can now be specified in transport:destination notation, just like the mailbox_transport and fallback_transport parameters. The :destination part is optional. However, these parameters take only one destination, unlike relayhost and fallback-relay which take any number of destinations. More general virtual domain support. Postfix now supports both Sendmail-style virtual domains and Postfix-style virtual domains. Details and examples are given in the revised virtual manual page. - With Sendmail-style virtual domains, local users/aliases/mailing lists are visible as localname@virtual.domain. This is convenient if you want to host mailing lists under virtual domains. - With Postfix-style virtual domains, local users/aliases/mailing lists are not visible as localname@virtual.domain. Each virtual domain has its own separate name space. More general "soft bounce" feature. Specify "soft_bounce = yes" in main.cf to prevent the SMTP server from bouncing mail while you are testing configurations. Until this release the SMTP server was not aware of soft bounces. Workarounds for non-standard RFC 2554 (AUTH command) implementations. Specify "broken_sasl_auth_clients = yes" to enable SMTP server support for old Microsoft client applications. The Postfix SMTP client supports non-standard RFC 2554 servers by default. All time-related configuration parameters now accept a one-letter suffix to indicate the time unit (s: second, m: minute, h: hour, d: day, w: week). The exceptions are the LDAP and MYSQL modules which are maintained separately. New "import_environment" and "export_environment" configuration parameters provide explicit control over what environment variables Postfix will import, and what environment variables Postfix will pass on to a non-Postfix process. In order to improve performance of one-to-one deliveries, Postfix by default now looks at up to 10000 messages at a time (was: 1000). Specify "syslog_facility = log_local1" etc. to separate the logging from multiple Postfix instances. However, a non-default logging facility takes effect only after process initialization. Errors during command-line parsing are still logged with the default syslog facility, as are errors while processing the main.cf file. Postfix now strips out Content-Length: headers in incoming mail to avoid confusion in mail user agents. Specify "require_home_directory = yes" to prevent mail from being delivered to a user whose home directory is not mounted. This feature is implemented by the Postfix local delivery agent. The pipe mailer has a size limit (size=nnn) command-line argument. The pipe delivery agent has a configurable end-of-line attribute. Specify "pipe ... eol=\r\n" for delivery mechanisms that require CRLF record delimiters. The eol attribute understands the following C-style escape sequences: \a \b \f \n \r \t \v \nnn \\. In master.cf you can selectively override main.cf configuration parameters, for example: "smtpd -o myhostname=foo.com". In main.cf, specify "smtp_bind_address=x.x.x.x" to bind SMTP connections to a specific local interface. Or override the default setting in master.cf with "smtp -o smtp_bind_address=x.x.x.x". For now, you must specify a numeric IP address. Questionable feature: with "smtp_always_send_ehlo = yes", the SMTP client sends EHLO regardless of the content of the SMTP server's greeting. Specify "-d key" to postalias or postmap in order to remove one key. This still needs to be generalized to multi-key removal (e.g., read keys from stdin). Comments in Postfix configuration files no longer contain troff formatting codes. The text is now generated from prototype files in a new "proto" subdirectory. Major changes with postfix-19991231: ==================================== - It is now much more difficult to configure Postfix as an open relay. The SMTP server requires that "smtpd_recipient_restrictions" contains at least one restriction that by default refuses mail (as is the default). There were too many accidents with changes to the UCE restrictions. - The relay_domains parameter no longer needs to contain $virtual_maps. - Overhauled FAQ (html/faq.html) with many more examples. - Updated UCE documentation (html/uce.html) with more examples. More UCE configuration examples in sample configuration files. - Several little improvements to the installation procedure: relative symlinks, configurable directory for scratch files so the installation can be done without write access to the build tree. - Updated LDAP client code (John Hensley). - Updated mysql client code (Scott Cotton). - The SMTP server now rejects mail for unknown users in virtual domains that are defined by Postfix virtual maps. - The SMTP server can reject mail for unknown local users. Specify "local_recipient_maps = $alias_maps, unix:passwd.byname" if your local mail is delivered by a UNIX-style local delivery agent. See example in conf/main.cf. - Use "disable_vrfy_command = yes" to disable the SMTP VRFY command. This prevents some forms of address harvesting. - The sendmail "-f" option now understands and even understands forms with RFC 822-style comments. - New "qmgr_fudge_factor" parameter allows you to balance mailing list performance against response time for one-to-one mail. The fudge factor controls what percentage of delivery resources Postfix will devote to one message. With 100%, delivery of one message does not begin before delivery of the previous message is completed. This is good for list performance, bad for one-to-one mail. With 10%, response time for one-to-one mail improves much, but list performance suffers: in the worst case, people near the start of a mailing list get a burst of postings today, while people near the end of the list get that same burst of postings a whole day later. - It is now relatively safe to configure 550 status codes for the main.cf unknown_address_reject_code or unknown_client_reject_code parameters. The SMTP server now always sends a 450 (try again) reply code when an UCE restriction fails due to a soft DNS error, regardless of what main.cf specifies. - The RBL checks now show the content of TXT records (Simon J Mudd). - The Postfix SMTP server now understands a wider range of illegal address forms in MAIL FROM and RCPT TO commands. In order to disable illegal forms, specify "strict_rfc821_envelopes = yes". This also disables support for MAIL FROM and RCPT TO addresses without <>. - Per-client/helo/sender/recipient UCE restrictions (fully-recursive UCE restriction parser). See the RESTRICTION_CLASS file for details. - Use "postmap -q key" or "postalias -q key" for testing Postfix lookup tables or alias files. - Use "postconf -e name=value..." to edit the main.cf file. This is easier and safer than editing the main.cf file by hand. The edits are done on a temporary copy that is renamed into place. - Use "postconf -m" to display all supported lookup table types (Scott Cotton). - New "permit_auth_destination" UCE restriction for finer-grained access control (Jesper Skriver). Incompatible changes with postfix-19990906 ========================================== - On systems that use user.lock files to protect system mailboxes against simultaneous updates, Postfix now uses /file/name.lock files while delivering to files specified in aliases/forward/include files. This is a no-op when the recipient lacks directory write permission. - The LDAP client code no longer looks up a name containing "*" because it could be abused. See the LDAP_README file for how to restore previous behavior. - The Postfix to PCRE interface now expects PCRE version 2.08. Postfix is no longer compatible with PCRE versions prior to 2.06. Major changes with postfix-19990906 =================================== Several bugfixes, none related to security. See the HISTORY file for a complete list of changes. - Postfix is now distributed under IBM Public License Version 1.0 which does not carry the controversial termination clause. The new license does have a requirement that contributors make source code available. - INSTALL.sh install/upgrade procedure that replaces existing programs and shell scripts instead of overwriting them, and that leaves existing queue files and configuration files alone. - The ugly Delivered-To: header can now be turned off selectively. The default setting is: "prepend_delivered_header = command, file, forward". Turning off the Delivered-To: header when forwarding mail is not recommended. - mysql client support by Scott Cotton and Joshua Marcus, Internet Consultants Group, Inc. See the file MYSQL_README for instructions. - reject_unauth_destination SMTP recipient restriction that rejects destinations not in $relay_domains. Unlike the check_relay_domains restriction, reject_unauth_destination ignores the client hostname. By Lamont Jones of Hewlett-Packard. - reject_unauth_pipelining SMTP *anything* restriction to stop mail from spammers that improperly use SMTP command pipelining to speed up their deliveries. - Postfix "sendmail" now issues a warning and drops privileges if installed set-uid root. - No more duplicate delivery when "postfix reload" is immediately followed by "sendmail -q". - No more "invalid argument" errors when a Postfix daemon opens a DB/DBM file while some other process is changing the file. - Portability to the Mac OS X Server, Reliant Unix, AIX 3.2.5 and Ultrix 4.3. Incompatible changes with postfix-19990601: =========================================== - The SMTP server now delays all UCE restrictions until the RCPT TO, VRFY or ETRN command. This makes the restrictions more useful, because many SMTP clients do not expect negative responses earlier in the protocol. In order to restore the old behavior, specify "smtpd_delay_reject = no" in /etc/postfix/main.cf. - The Postfix local delivery agent no longer automatically propagates address extensions to aliases/include/forward addresses. Specify "propagate_unmatched_extensions = canonical, virtual, alias, forward, include" to restore the old behavior. - The Postfix local delivery agent no longer does $name expansion on words found in the mailbox_command configuration parameter. This makes it easier to specify shell syntax. See conf/main.cf. - The luser_relay syntax has changed. You can specify one address; it is subjected to $user, etc. expansions. See conf/main.cf. - File system reorganization: daemon executables are now in the libexec subdirectory, command executables in the bin subdirectory. The INSTALL instructions now recommend installing daemons and commands into separate directories. Major changes with postfix-19990601: ===================================== - New USER, EXTENSION, LOCAL, DOMAIN and RECIPIENT environment variables for delivery to command (including mailbox_command) by the local delivery agent. As you might expect, the information is censored. The list of acceptable characters is specified with the command_expansion_filter configuration parameter. Unacceptable characters are replaced by underscores. See html/local.8.html. - Specify "forward_path = /var/forward/$user" to avoid looking up .forward files in user home directories. The default value is $home/.forward$recipient_delimiter$extension, $home/.forward. Initial code by Philip A. Prindeville, Mirapoint, Inc., USA. - Conditional $name expansion in forward_path and luser_relay. Available names are: $user (bare user name) $shell (user login shell), $home (user home directory), $local (everything to the left of @), $extension (optional address extension), $domain (everything to the right of @), $recipient (the complete address) and $recipient_delimiter. A simple $name expands as usual. ${name?value} expands to value when $name is defined. ${name:value} expands to value when $name is not defined. With ${name?value} and ${name:value}, the value is subject to another iteration of $name expansion. - POSIX regular expression support, enabled by default on 4.4BSD, LINUX, HP-UX, and Solaris 2.5 and later. See conf/sample-regexp.cf. Initial code by Lamont Jones, Hewlett-Packard, borrowing heavily from the PCRE implementation by Andrew McNamara, connect.com.au Pty. Ltd., Australia. - Regular expression checks for message headers. This requires support for POSIX or for PCRE regular expressions. Specify "header_checks = regexp:/file/name" or "header_checks = pcre:/file/name", and specify "/^header-name: badstuff/ REJECT" in the pattern file (patterns are case-insensitive by default). Code by Lamont Jones, Hewlett-Packard. It is to be expected that full content filtering will be delegated to an external command. - Regular expression support for all lookup tables, including access control (full mail addresses only), address rewriting (canonical/virtual, full mail addresses only) and transport tables (full domain names only). However, regular expressions are not allowed for aliases, because that would open up security exposures. - Automatic detection of changes to DB or DBM lookup tables. This eliminates the need to run "postfix reload" after each change to the SMTP access table, or to the canonical, virtual, transport or aliases tables. - New error mailer. Specify ".domain.name error:domain is undeliverable" in the transport table to bounce mail for entire domains. - No more Postfix lockups on Solaris (knock on wood). The code no longer uses Solaris UNIX-domain sockets, because they are still broken, even with Solaris 7. - Workaround for the Solaris mailtool, which keeps an exclusive kernel lock on the mailbox while its window is not iconified (specify "sun_mailtool_compatibility = yes" in main.cf). - Questionable workaround for Solaris, which reportedly loses long-lived exclusive locks that are held by the master daemon. - New reject_unknown_{sender,recipient}_domain restrictions for sender and recipient mail addresses that distinguish between soft errors (always 450) and hard errors (unknown_address_reject_code, default 450). - MIME-encapsulated bounce messages, making it easier to recover bounced mail. Initial implementation by Philip A. Prindeville, Mirapoint, Inc., USA. Support for RFC 1892 (multipart/report) and RFC 1894 (DSN) will have to wait until Postfix internals have been revised to support RFC 1893. - Separately configurable "postmaster" addresses for single bounces (bounce_notice_recipient), double bounces (2bounce_notice_recipient), delayed mail (delay_notice_recipient), and for mailer error reports (error_notice_recipient). See conf/main.cf. - Questionable feature: specify "best_mx_transport = local" if this machine is the best MX host for domains not in mydestinations. Incompatible changes with postfix-19990317: =========================================== - You MUST install the new version of /etc/postfix/postfix-script. - The pipe mailer "flags" syntax has changed. You now explicitly MUST specify the R flag in order to generate a Return-Path: message header (as needed by, for example, cyrus). Major changes with postfix-19990317: ==================================== A detailed record of changes is given in the HISTORY file. - Less postmaster mail. Undeliverable bounce messages (double bounces) are now discarded. Specify "notify_classes = 2bounce..." to get copies of double bounces. Specify "notify_classes = bounce..." to get copies of normal and double bounces. - Improved LDAP client code by John Hensley of Merit Network, USA. See LDAP_README for details. - Perl-compatible regular expression support for lookup maps by Andrew McNamara, connect.com.au Pty. Ltd., Australia.. Example: "check_recipient_access pcre:/etc/postfix/sample-pcre.cf". Regular expressions provide a powerful tool not only for SMTP access control but also for address rewriting. See PCRE_README for details. - Automatic notification of delayed mail (disabled by default). With "delay_warning_time = 4", Postfix informs senders when mail has not been delivered after 4 hours. Initial version of the code by Daniel Eisenbud, University of California at Berkeley. In order to get postmaster copies of such warnings, specify "notify_classes = delay...". - More configurable local delivery: "mail_spool_directory" to specify the UNIX mail spool directory; "mailbox_transport" to delegate all mailbox delivery to, for example, cyrus, and "fallback_transport" to delegate delivery of only non-UNIX users. And all this without losing local aliases and local .forward processing. See config/main.cf and config/master.cf. - Several changes to improve Postfix behavior under worst-case conditions (frequent Postfix restarts/reloads combined with lots if inbound mail, intermittent connectivity problems, SMTP servers that become comatose after receiving QUIT). - More NFS-friendly mailbox delivery. The local delivery agent now avoids using root privileges where possible. - For sites that do not receive mail at all, mydestination can now be an empty string. Be sure to set up a transport table entry to prevent mail from looping. - New "postsuper" utility to clean up stale files from Postfix queues. - Workaround for BSD select() collisions that cause performance problems on large BSD systems. - Several questionable but useful features to capture mail: "always_bcc = address" to capture a copy of every message that enters the system, and "luser_relay = address" to capture mail for unknown recipients (does not work when mailbox_transport or fallback_transport are being used). - Junk mail controls: new reject_non_fqdn_{hostname,sender,recipient} restrictions to reject non-FQDN arguments in HELO, MAIL FROM and RCPT TO commands, and stricter checking of numeric HELO arguments. - "fallback_relay" feature for sites that use DNS but that can't talk to the entire world. The fall-back relay gets the mail when a destination is not found in the DNS or when the destination is found but not reachable. - Several questionable controls that can help to keep mail going: specify "smtp_skip_4xx_greeting = yes" to skip SMTP servers that greet with 4XX, "ignore_mx_lookup_error = yes" to look up an A record when a DNS server does not respond to an MX query. Incompatible changes with postfix-beta-19990122-pl01: ===================================================== None. Major changes with postfix-beta-19990122-pl01: ============================================== - Restrict who may use ETRN and what domains may be specified. Example: "smtpd_etrn_restrictions = permit_mynetworks, reject". - BIFF notifications. For compatibility reasons this feature is on by default. Specify "biff = no" in main.cf if your machine has lots of shell users. - With "soft_bounce = yes", defer delivery instead of bouncing mail. This is a safety net for configuration errors with delivery agents. It has no effect on errors in virtual maps, canonical maps, or in junk mail restrictions. - Specify "owner_request_special = no" to turn off special treatment of owner-foo and foo-request addresses. Incompatible changes with postfix-beta-19990122: ================================================ - The syntax of the transport table has changed. An entry like: customer.org smtp:[gateway.customer.org] no longer forwards mail for anything.customer.org. For that you need to specify: customer.org smtp:[gateway.customer.org] .customer.org smtp:[gateway.customer.org] This change makes transport tables more compatible with sendmail mailer tables. - The format of syslog records has changed. A client is now always logged as hostname[address]; the pickup daemon logs queue file uid and sender address. Major changes with postfix-beta-19990122: ========================================= - Junk mail restrictions can now be postponed to the RCPT TO command. Specify: "smtpd_recipient_restrictions = reject_maps_rbl...". - More flexible interface for delivery to e.g., cyrus IMAP without need for PERL scripts to munge recipient addresses. In addition to $sender, $nexthop and $recipient, the pipe mailer now also supports $user, $extension and $mailbox. - New mail now has precedence over deferred mail, plus some other tweaks to make bulk mail go faster. But it ain't no cure for massive network outages. - Watchdog timer for systems that cause the Postfix queue manager to lock up, so it recovers without human intervention. - Delivery to qmail-style maildir files, which is good for NFS environments. Specify "home_mailbox = Maildir/", or specify /file/name/ in aliases or in .forward files. The trailing / is required to turn on maildir delivery. - Incremental updates of aliases and maps. Specify "postmap -i mapname" and it will read new entries from stdin. - Newaliases will now update more than one alias database. Specify the names with the main.cf "alias_database" parameter. - Address masquerading exceptions to prevent users from being masqueraded. Specify "masquerade_exceptions = root". - A pipelined SMTP client. Deliveries to Postfix, qmail, LSOFT, zmailer, and exim (once it's fixed) speed up by some 30% for short messages with one recipient, with more for multi-recipient mails. - Hook for local delivery to "|command" via the smrsh restricted shell, to restrict what commands may be used in .forward etc. files. Specify "local_command_shell = /some/where/smrsh -c".