The kernel has the capability to accept information at boot in the form of a `command line', similar to an argument list you would give to a program. In general this is used to supply the kernel with information about hardware parameters that the kernel would not be able to determine on its own, or to avoid/override the values that the kernel would otherwise detect.
It is the job of the boot loader (e.g. LILO, loadlin or Grub) to take this information from the user and put it in a previously agreed upon place where the kernel can find it once it starts.
This present revision covers kernels up to and including v2.4.20. and v2.5.63
The BootPrompt-Howto is by:
Paul Gortmaker, p_gortmaker @ yahoo.com
This document is Copyright (c) 1995-2003 by Paul Gortmaker. Please see the Disclaimer and Copying information at the end of this document ( copyright) for information about redistribution of this document and the usual `we are not responsible for what you manage to break...' type legal stuff.
Most Linux users should never have to even look at this document. Linux does an exceptionally good job at detecting most hardware and picking reasonable default settings for most parameters. The information in this document is aimed at users who might want to change some of the default settings to optimize the kernel to their particular machine, or to a user who has `rolled their own' kernel to support a not so common piece of hardware for which the automatic defaults are not optimal.
For the sake of this document it is best to break the
boot arguments into two general categories; (a)ones
handled by the kernel and (b)those being handled by a device driver.
Examples would be init= which tells the kernel what the
first program to run should be, versus aha154x= which
tells a device driver for a SCSI card what hardware resources it
should use are. This document concentrates on giving detailed
information on those in (a) for reasons outlined below.
IMPORTANT NOTE: Driver related boot prompt arguments
only apply to hardware drivers that are compiled directly into the
kernel. They have no effect on drivers that are loaded
as modules. Most Linux distributions come with a basic `bare-bones'
kernel, and the drivers are small modules that are loaded after
the kernel has initialized.
If you are unsure if you are using modules then try lsmod,
look at man depmod and man modprobe along with the
contents of your /etc/modules.conf.
In light of this, device driver boot prompt arguments are only really used by a few people who are building their own kernels, and thus have the kernel source at hand. These people are usually going to check the source for the options and syntax required by that driver to get the most up to date info.
For example, if you were looking for what arguments could be
passed to the AHA1542 SCSI driver, then you would go to the
linux/drivers/scsi directory, and look in the
file aha1542.c for __setup(... , ...). The
first thing in brackets is the argument you provide at boot,
and the second thing is the name of the function that processes your
argument. Usually near the top of this function or at the
top of the source file you will find a description of the boot
time arguments that the driver accepts.
For a while now, the kernel source has come with the file
linux/Documentation/kernel-parameters.txt. This
file contains a brief listing of all the boot time arguments
that you can provide, along with quick pointers to where in
the source you can find where the arguments are parsed.
The idea is that this file gives developers a quick and
easy place to add in a brief description of any new arguments
that they add while working on the source. As such, it
will probably always be more up to date than this document.
Actually, I'm considering discontinuing this document in light
of the existence of kernel-parameters.txt. (Opinions?)
The linux directory is usually found in /usr/src/
for most distributions. All references in this document
to files that come with the kernel will have their pathname
abbreviated to start with linux - you will have to add the
/usr/src/ or whatever is appropriate for your system.
Some distributions may not install the full kernel source by
default, and only put in the linux/include directory.
If you can't find the file in question, then install the kernel
source and/or make use of the find and locate commands.
If you can't find the kernel source package in your distribution
then the kernel source is available at:
The next best thing to reading the kernel C source itself, will
be any of the other documentation files that are
distributed with the kernel itself. There are now quite a
few of these, and most of them can be found in the directory
linux/Documentation and subdirectories from there.
Sometimes there will be README.foo files that can be found
in the related driver directory (e.g. linux/drivers/???/,
where examples of ??? could be scsi, char, or net).
The general trend is to move these files into the Documentation
directory, so if a file mentioned in this document is no longer
there, chances are it has been moved.
If you have figured out what boot-args you intend to use, and now want to know how to get that information to the kernel, then look at the documentation that comes with the software that you use to boot the kernel (e.g. LILO or loadlin). A brief overview is given below, but it is no substitute for the documentation that comes with the booting software.
New versions of this document can be retrieved via anonymous
FTP from most Linux FTP sites in the directory
/pub/Linux/docs/HOWTO/. Updates will be made as new
information and/or drivers becomes available. If this copy that
you are presently reading is more than six months old, then
you should probably check to see if a newer copy exists.
I would recommend viewing this via a WWW browser or in the
Postscript/dvi format. Both of these contain cross-references
that are lost in a simple plain text version.
If you want to get the official copy, here is URL.
This section gives some examples of software that can be used to pass kernel boot-time arguments to the kernel itself. It also gives you an idea of how the arguments are processed, what limitations there are on the boot args, and how they filter down to each appropriate device that they are intended for.
It is important to note that spaces should not be used in a boot argument, but only between separate arguments. A list of values that are for a single argument are to be separated with a comma between the values, and again without any spaces. See the following examples below.
ether=9,0x300,0xd0000,0xd4000,eth0 root=/dev/hda1 *RIGHT*
ether = 9, 0x300, 0xd0000, 0xd4000, eth0 root = /dev/hda1 *WRONG*
Once the Linux kernel is up and running, one can view the command
line arguments that were in place at boot by simply typing
cat /proc/cmdline at a shell prompt.
The LILO program (LInux LOader) written by Werner Almesberger is the most commonly used. It has the ability to boot various kernels, and stores the configuration information in a plain text file. Most distributions ship with LILO as the default boot-loader. LILO can boot DOS, OS/2, Linux, FreeBSD, etc. without any difficulties, and is quite flexible.
A typical configuration will have LILO stop and print LILO:
shortly after you turn on your computer. It will then wait for
a few seconds for any optional input from the user, and failing
that it will then boot the default system. Typical system labels
that people use in the LILO configuration files are linux
and backup and msdos. If you want to type in a boot
argument, you type it in here, after typing in the system label
that you want LILO to boot from, as shown in the example below.
LILO: linux root=/dev/hda1
LILO comes with excellent documentation, and for the purposes
of boot args discussed here, the LILO append= command
is of significant importance when one wants to add a boot time
argument as a permanent addition to the LILO config file.
You simply add something like append = "foo=bar" to the
/etc/lilo.conf file. It can either be added at the top
of the config file, making it apply to all sections, or to a
single system section by adding it inside an image= section.
Please see the LILO documentation for a more complete description.
The other commonly used Linux loader is `LoadLin' which is a DOS program that has the capability to launch a Linux kernel from the DOS prompt (with boot-args) assuming that certain resources are available. This is good for people that use DOS and want to launch into Linux from DOS.
It is also very useful if you have certain hardware which relies
on the supplied DOS driver to put the hardware into a known
state. A common example is `SoundBlaster Compatible' sound
cards that require the DOS driver to set a few proprietary
registers to put the card into a SB compatible mode. Booting
DOS with the supplied driver, and then loading Linux from
the DOS prompt with LOADLIN.EXE avoids the reset of
the card that
happens if one rebooted instead. Thus the card is left in a
SB compatible mode and hence is useable under Linux.
There are also other programs that can be used to boot Linux.
For a complete list, please look at the programs available
on your local Linux ftp mirror, under system/Linux-boot/.
There are a few of the kernel boot parameters that have their
default values stored in various bytes in the kernel image itself.
There is a utility called rdev that is installed on most
systems that knows where these values are, and how to change them.
It can also change things that have no kernel boot argument
equivalent, such as the default video mode used.
The rdev utility is usually also aliased to swapdev, ramsize, vidmode and rootflags. These are the five things that rdev can change, those being the root device, the swap device, the RAM disk parameters, the default video mode, and the readonly/readwrite setting of root device.
More information on rdev can be found by typing
rdev -h or by reading the supplied man page (man rdev).
Most of the boot args take the form of:
name[=value_1][,value_2]...[,value_11]
where `name' is a unique keyword that is used to identify what part of the kernel the associated values (if any) are to be given to. Multiple boot args are just a space separated list of the above format. Note the limit of 11 is real, as the present code only handles 11 comma separated parameters per keyword. (However, you can re-use the same keyword with up to an additional 11 parameters in unusually complicated situations, assuming the setup function supports it.) Also note that the kernel splits the list into a maximum of ten integer arguments, and a following string, so you can't really supply 11 integers unless you convert the 11th arg from a string to an int in the driver itself.
Most of the sorting goes on in linux/init/main.c.
First, the kernel checks to see if the argument is any of
the special arguments `root=', `ro', `rw', or `debug'.
The meaning of these special arguments is described further
on in the document.
Then it walks a list of setup functions (contained in the
bootsetups array) to see if the specified
argument string (such as `foo') has been associated with a
setup function (foo_setup()) for a particular
device or part of the kernel. If you
passed the kernel the line foo=3,4,5,6,bar then the
kernel would search the bootsetups array to see if
`foo' was registered. If it was, then it would call the
setup function associated with `foo' (foo_setup())
and hand it the integer arguments
3, 4, 5 and 6 as given on the kernel command line, and
also hand it the string argument bar.
Anything of the form `foo=bar' that is not accepted as a
setup function as described above is then interpreted as an
environment variable to be set. An example would
be to use TERM=vt100 or BOOT_IMAGE=vmlinuz.bak
as a boot argument. These environment
variables are typically tested for in the initialization
scripts to enable or disable a wide range of things.
Any remaining arguments that were not picked up by the
kernel and were not interpreted as environment variables
are then passed onto process one, which is usually the
init program. The most common argument that is passed to
the init process is the word single which instructs
init to boot the computer in single user mode, and not
launch all the usual daemons. Check the manual page for the
version of init installed on your system to see what
arguments it accepts.
These are the boot arguments that are not related to any specific device or peripheral. They are instead related to certain internal kernel parameters, such as memory handling, ramdisk handling, root file system handling and others.
The following options all pertain to how the kernel selects and handles the root filesystem.
This argument tells the kernel what device is to be used as the root filesystem while booting. The default of this setting is the value of the root device of the system that the kernel was built on. For example, if the kernel in question was built on a system that used `/dev/hda1' as the root partition, then the default root device would be `/dev/hda1'. To override this default value, and select the second floppy drive as the root device, one would use `root=/dev/fd1'.
Valid root devices are any of the following devices:
(1) /dev/hdaN to /dev/hddN, which is partition N on ST-506 compatible disk `a to d'.
(2) /dev/sdaN to /dev/sdeN, which is partition N on SCSI compatible disk `a to e'.
(3) /dev/xdaN to /dev/xdbN, which is partition N on XT compatible disk `a to b'.
(4) /dev/fdN, which is floppy disk drive number N. Having N=0 would be the DOS `A:' drive, and N=1 would be `B:'.
(5) /dev/nfs, which is not really a device, but rather a flag to tell the kernel to get the root fs via the network.
(6) /dev/ram, which is the RAM disk.
The more awkward and less portable numeric specification
of the above possible disk devices in major/minor format is
also accepted. (e.g. /dev/sda3 is major 8, minor 3, so you
could use root=0x803 as an alternative.)
This is one of the few kernel boot arguments that has its
default stored in the kernel image, and which can thus
be altered with the rdev utility.
This option allows you to give options pertaining to the
mounting of the root filesystem just as you would to the
mount program. An example could be giving the
noatime option to an ext2 fs.
This option allows you to give a comma separated list of fs types that will be tried for a match when trying to mount the root filesystem. This list will be used instead of the internal default which usually starts with ext2, minix and the like.
When the kernel boots, it needs a root filesystem to read basic things off of. This is the root filesystem that is mounted at boot. However, if the root filesystem is mounted with write access, you can not reliably check the filesystem integrity with half-written files in progress. The `ro' option tells the kernel to mount the root filesystem as `readonly' so that any filesystem consistency check programs (fsck) can safely assume that there are no half-written files in progress while performing the check. No programs or processes can write to files on the filesystem in question until it is `remounted' as read/write capable.
This is one of the few kernel boot arguments that has its
default stored in the kernel image, and which can thus
be altered with the rdev utility.
This is the exact opposite of the above, in that it tells the kernel to mount the root filesystem as read/write. The default is to mount the root filesystem as read only. Do not run any `fsck' type programs on a filesystem that is mounted read/write.
The same value stored in the image file mentioned above is
also used for this parameter, accessible via rdev.
This argument tells the kernel which machine, what directory
and what NFS options to use for the root filesystem.
Also note that
the argument root=/dev/nfs is required. Detailed
information on using an NFS root fs is in the file
linux/Documentation/nfsroot.txt.
If you are using NFS as a root filesystem, then there is no
programs like ifconfig and route present until
the root fs is mounted, and so the
kernel has to configure the network interfaces directly.
This boot argument sets up the various network interface addresses
that are required to communicate over the network. If this argument
is not given, then the kernel tries to use RARP and/or BOOTP to
figure out these parameters.
The following options all relate to how the kernel handles the RAM disk device, which is usually used for bootstrapping machines during the install phase, or for machines with modular drivers that need to be installed to access the root filesystem.
To allow a kernel image to reside on a floppy disk along with a compressed ramdisk image, the `ramdisk_start=<offset>' command was added. The kernel can't be included into the compressed ramdisk filesystem image, because it needs to be stored starting at block zero so that the BIOS can load the bootsector and then the kernel can bootstrap itself to get going.
Note: If you are using an uncompressed ramdisk image, then the kernel can be a part of the filesystem image that is being loaded into the ramdisk, and the floppy can be booted with LILO, or the two can be separate as is done for the compressed images.
If you are using a two-disk boot/root setup (kernel on disk 1, ramdisk image on disk 2) then the ramdisk would start at block zero, and an offset of zero would be used. Since this is the default value, you would not need to actually use the command at all.
This parameter tells the kernel whether it is to try to load a ramdisk image or not. Specifying `load_ramdisk=1' will tell the kernel to load a floppy into the ramdisk. The default value is zero, meaning that the kernel should not try to load a ramdisk.
Please see the file linux/Documentation/ramdisk.txt
for a complete description of the new boot time arguments, and
how to use them. A description of how this parameter can be set
and stored in the kernel image via `rdev' is also described.
This parameter tells the kernel whether or not to give you a prompt asking you to insert the floppy containing the ramdisk image. In a single floppy configuration the ramdisk image is on the same floppy as the kernel that just finished loading/booting and so a prompt is not needed. In this case one can use `prompt_ramdisk=0'. In a two floppy configuration, you will need the chance to switch disks, and thus `prompt_ramdisk=1' can be used. Since this is the default value, it doesn't really need to be specified. ( (Historical note: Sneaky people used to use the `vga=ask' LILO option to temporarily pause the boot process and allow a chance to switch from boot to root floppy.)
Please see the file linux/Documentation/ramdisk.txt
for a complete description of the new boot time arguments, and
how to use them. A description of how this parameter can be set
and stored in the kernel image via `rdev' is also described.
While it is true that the ramdisk grows dynamically as required, there is an upper bound on its size so that it doesn't consume all available RAM and leave you in a mess. The default is 4096 (i.e. 4MB) which should be large enough for most needs. You can override the default to a bigger or smaller size with this boot argument.
Please see the file linux/Documentation/ramdisk.txt
for a complete description of the new boot time arguments, and
how to use them. A description of how this parameter can be set
and stored in the kernel image via `rdev' is also described.
This can be tuned for better memory management behaviour.
Quoting from the ramdisk driver rd.c:
It would be very desirable to have a soft-blocksize (that in the case of the ramdisk driver is also the hardblocksize ;) of PAGE_SIZE because doing that we'll achieve a far better MM footprint. Using a rd_blocksize of BLOCK_SIZE in the worst case we'll make PAGE_SIZE/BLOCK_SIZE buffer-pages unfreeable. With a rd_blocksize of PAGE_SIZE instead we are sure that only 1 page will be protected. Depending on the size of the ramdisk you may want to change the ramdisk blocksize to achieve a better or worse MM behaviour. The default is still BLOCK_SIZE (needed by rd_load_image that supposes the filesystem in the image uses a BLOCK_SIZE blocksize)
(NOTE: This argument is obsolete, and should not be used except
on kernels v1.3.47 and older. The commands that should be used
for the ramdisk device are documented above. Newer kernels
may accept this as an alias for ramdisk_size.)
This specifies the size in kB of the RAM disk device. For example, if one wished to have a root filesystem on a 1.44MB floppy loaded into the RAM disk device, they would use:
ramdisk=1440
This is one of the few kernel boot arguments that has its
default stored in the kernel image, and which can thus
be altered with the rdev utility.
The v2.x and newer kernels have a feature where the root filesystem
can be initially a RAM disk, and the kernel executes /linuxrc
on that RAM image. This feature is typically used to allow loading
of modules needed to mount the real root filesystem (e.g. load
the SCSI driver modules stored in the RAM disk image, and then
mount the real root filesystem on a SCSI disk.)
The actual `noinitrd' argument determines what happens to the
initrd data after the kernel has booted. When
specified, instead of converting it to a RAM disk, it
is accessible via /dev/initrd, which can be read once
before the RAM is released back to the system. For full details
on using the initial RAM disk, please consult
linux/Documentation/initrd.txt. In addition, the most
recent versions of LILO and LOADLIN should have additional
useful information.
The following arguments alter how Linux detects or handles the physical and virtual memory of your system.
Override level 2 CPU cache size detection (in kB). Sometimes CPU hardware bugs make them report the cache size incorrectly. The kernel will attempt work arounds to fix known problems, but for some CPUs it is not possible to determine what the correct size should be. This option provides an override for these situations.
This argument has several purposes: The original purpose was to specify the amount of installed memory (or a value less than that if you wanted to limit the amount of memory available to linux).
The next (and hardly used) purpose is to specify
mem=nopentium which tells the Linux kernel to not use
the 4MB page table performance feature. If you want to use
it for both purposes, use a separate mem= for each one.
The original BIOS call defined in the PC specification that
returns the amount of installed memory was only designed to
be able to report up to 64MB. (Yes, another lack of foresight,
just like the 1024 cylinder disks... sigh.) Linux uses this
BIOS call at boot to determine how much memory is installed.
A newer specification (e820) allows the BIOS to get this right
on most machines nowadays. If you have more than 64MB of RAM
installed on an older machine, you can use this
boot argument to tell Linux how much memory you have.
Here is a quote from Linus on the usage of the mem= parameter.
``The kernel will accept any `mem=xx' parameter you give it, and if it turns out that you lied to it, it will crash horribly sooner or later. The parameter indicates the highest addressable RAM address, so `mem=0x1000000' means you have 16MB of memory, for example. For a 96MB machine this would be `mem=0x6000000'. If you tell Linux that it has more memory than it actually does have, bad things will happen: maybe not at once, but surely eventually.''
Note that the argument does not have to be in hex, and the
suffixes `k' and `M' (case insensitive) can be used to specify
kilobytes and Megabytes, respectively. (A `k' will cause a 10 bit
shift on your value, and a `M' will cause a 20 bit shift.)
A typical example for a 128MB machine would be "mem=128m".
In some cases, the memory reported via e820 can also be wrong,
and so the mem=exactmap was added. You use this in
conjunction with specifying an exact memory map, such as:
mem=exactmap mem=640K@0 mem=1023M@1M
for a 1GB machine with the usual 384k of ISA memory mapped I/O space excluded from use.
Memory is broken down into zones; on i386 these zones
correspond to `DMA' (for legacy ISA devices that can only address
up to 16MB via DMA); `Normal' for memory from 16MB up to 1GB,
and `HighMem' for memory beyond 1GB (assuming your kernel
was built with high mem support enabled). The two (or three)
integers supplied here determine how much memory in each zone
should be kept free - with the size of the zone divided by the
number supplied being used as the minimum (so smaller numbers
mean keep more free in the zone). The defaults are currently
memfrac=32,128,128.
This allows the user to tune some of the virtual memory (VM) parameters that are related to swapping to disk. It accepts the following eight parameters:
MAX_PAGE_AGE
PAGE_ADVANCE
PAGE_DECLINE
PAGE_INITIAL_AGE
AGE_CLUSTER_FRACT
AGE_CLUSTER_MIN
PAGEOUT_WEIGHT
BUFFEROUT_WEIGHT
Interested hackers are advised to have a read of
linux/mm/swap.c and also make note of the goodies in
/proc/sys/vm. Kernels come with some
useful documentation on this in the
linux/Documentation/vm/ directory.
Similar to the `swap=' argument, this allows the user to tune some of the parameters related to buffer memory management. It accepts the following six parameters:
MAX_BUFF_AGE
BUFF_ADVANCE
BUFF_DECLINE
BUFF_INITIAL_AGE
BUFFEROUT_WEIGHT
BUFFERMEM_GRACE
Interested hackers are advised to have a read of
linux/mm/swap.c and also make note of the goodies
in /proc/sys/vm. Kernels come with some
useful documentation on this in the
linux/Documentation/vm/ directory.
These various boot arguments let the user tune certain internal kernel parameters.
Currently this only accepts `off' to disable the ACPI subsystem.
Usually the console is the 1st virtual terminal, and so boot
messages appear on your VGA screen. Sometimes it is nice to
be able to use another device like a serial port (or even a
printer!) to be the console when no video device is present.
It is also useful to capture boot time messages if a problem
stops progress before they can be logged to disk.
An example would be to use
console=ttyS1,9600 for selecting the 2nd serial port
at 9600 baud to be the console.
More information can be found in
linux/Documentation/serial-console.txt.
The kernel communicates important (and not-so important)
messages to the operator via the printk() function.
If the message is considered important, the printk()
function will put a copy on the present console as well
as handing it off to the klogd() facility so that it
gets logged to disk. The reason for printing important
messages to the console as well as logging them to disk is
because under unfortunate circumstances (e.g. a disk failure)
the message won't make it to disk and will be lost.
The threshold for what is and what isn't considered important
is set by the console_loglevel variable. The default is
to log anything more important than DEBUG (level 7) to
the console. (These levels are defined in the include file
kernel.h) Specifying debug as a boot argument will
set the console loglevel to 10, so that all kernel
messages appear on the console.
The console loglevel can usually also be set at run time via
an option to the klogd() program. Check the man page
for the version installed on your system to see how to do this.
If you are using DECnet, you can supply two comma separated integers here to give your area and node respectively.
If you are using devfs, instead of the standard static
devices in /dev/ then you can supply the words
only or mount with this argument.
There are also additional debug arguments that are listed
in the source.
If you are using EFI GUID Partition Table handling, you can use this to override problems associated with an invalid PMBR.
Setting this to `poll' causes the idle loop in the kernel to poll on the need reschedule flag instead of waiting for an interrupt to happen. This can result in an improvement in performance on SMP systems (albeit at the cost of an increase in power consumption).
The kernel defaults to starting the `init' program at boot,
which then takes care of setting up the computer for users
via launching getty programs, running `rc' scripts and the like.
The kernel first looks for /sbin/init, then
/etc/init (depreciated), and as a last resort, it
will try to use /bin/sh (possibly on /etc/rc).
If for example, your init program got corrupted and thus stopped
you from being able to boot, you could simply use the boot prompt
init=/bin/sh which would drop you directly into a
shell at boot, allowing you to replace the corrupted program.
This takes the form of:
isapnp=read_port,reset,skip_pci_scan,verbose
This takes the form of:
isapnp_reserve_dma=n1,n2,n3,...nN
where n1 ... nN are the DMA channel numbers to not use for PnP.
This takes the form of:
isapnp_reserve_irq=io1,size1,io2,size2,...ioN,sizeN
where ioX,sizeX are I/O start and length pairs of regions
in I/O space that are not to be used by PnP.
This takes the form of:
isapnp_reserve_irq=n1,n2,n3,...nN
where n1 ... nN are the interrupt numbers to not use for PnP.
This takes the form of:
isapnp_reserve_mem=mem1,size1,mem2,size2,...memN,sizeN
where ioX,sizeX are I/O start and length pairs of regions
in memory space that are not to be used by PnP.
Normally on i386 based machines, the Linux kernel does not reset the keyboard controller at boot, since the BIOS is supposed to do this. But as usual, not all machines do what they should. Supplying this option may help if you are having problems with your keyboard behaviour. It simply forces a reset at initialization time. (Some have argued that this should be the default behaviour anyways).
These tell the kernel to use the given port numbers for NFS lockd operation (for either UDP or TCP operation).
The number given with this argument limits the maximum
number of CPUs activated in SMP mode. Using a value of
0 is equivalent to the nosmp option.
The IBM model 95 Microchannel machines seem to lock up on the test that Linux usually does to detect the type of math chip coupling. Since all Pentium chips have a built in math processor, this test (and the lock up problem) can be avoided by using this boot option.
If your root filesystem is on a Multiple Device then you can
use this (assuming you compiled in boot support) to tell the
kernel the multiple device layout. The format (from the
file linux/Documentation/md.txt) is:
md=md_device_num,raid_level,chunk_size_factor,fault_level,dev0,dev1,...,devN
Where md_device_num is the number of the md device,
i.e. 0 means md0, 1 means md1, etc.
For raid_level, use -1 for linear mode and 0 for striped mode.
Other modes are currently unsupported.
The chunk_size_factor is for raid-0 and raid-1 only and
sets the chunk size as PAGE_SIZE shifted left the specified
amount. The fault_level is only for raid-1
and sets the maximum fault number to the specified number.
(Currently unsupported due to lack of boot support for raid1.)
The dev0-devN are a comma separated list of the devices that
make up the individual md device:
e.g. /dev/hda1,/dev/hdc1,/dev/sda1
See also raid=.
Supplying a non-zero integer will enable the non maskable interrupt watchdog (assuming IO APIC support is compiled in). This checks to see if the interrupt count is increasing (indicating normal system activity) and if it is not then it assumes that a processor is stuck and forces an error dump of diagnostic information.
Some i387 coprocessor chips have bugs that show up when used in 32 bit protected mode. For example, some of the early ULSI-387 chips would cause solid lockups while performing floating point calculations, apparently due to a bug in the FRSAV/FRRESTOR instructions. Using the `no387' boot argument causes Linux to ignore the math coprocessor even if you have one. Of course you must then have your kernel compiled with math emulation support! This may also be useful if you have one of those really old 386 machines that could use an 80287 FPU, as Linux can't use an 80287.
The i386 (and successors thereof) family of CPUs have a `hlt' instruction which tells the CPU that nothing is going to happen until an external device (keyboard, modem, disk, etc.) calls upon the CPU to do a task. This allows the CPU to enter a `low-power' mode where it sits like a zombie until an external device wakes it up (usually via an interrupt). Some of the early i486DX-100 chips had a problem with the `hlt' instruction, in that they couldn't reliably return to operating mode after this instruction was used. Using the `no-hlt' instruction tells Linux to just run an infinite loop when there is nothing else to do, and to not halt your CPU when there is no activity. This allows people with these broken chips to use Linux, although they would be well advised to seek a replacement through a warranty where possible.
Using this argument at boot disables scrolling features that make it difficult to use Braille terminals.
Using this option tells a SMP kernel to not use some of the
advanced features of the interrupt controller on multi processor
machines. Use of this option may be required when a device
(such as those using ne2k-pci or 3c59xi drivers) stops generating
interrupts (i.e. cat /proc/interrupts shows the same
interrupt count.)
See linux/Documentation/IO-APIC.txt for more information.
This will disable hyper-threading on intel processors that have this feature.
If ISA PnP is built into the kernel, this will disable it.
Some newer processors have the ability to self-monitor and detect inconsistencies that should not regularly happen. If an inconsistency is detected, a Machine Check Exception will take place and the system will be halted (rather than plundering forward and corrupting your data). You can use this argument to disable this feature, but be sure to check that your CPU is not overheating or otherwise faulty first.
Use of this option will tell a SMP kernel on a SMP machine to operate single processor. Typically only used for debugging and determining if a particular problem is SMP related.
If software suspend is enabled, and a suspend to disk file has been specified, using this argument will give a normal boot and the suspend data will be ignored.
Use of this option will tell the kernel to not use the Time Stamp Counter for anything, even if the CPU has one.
Use of this option will tell the kernel to not use any speed-up tricks involving the floating point unit, even if the processor supports them.
In the unlikely event of a kernel panic (i.e. an internal error
that has been detected by the kernel, and which the kernel decides
is serious enough to moan loudly and then halt everything), the
default behaviour is to just sit there until someone comes along
and notices the panic message on the screen and reboots the machine.
However if a machine is running unattended in an isolated location
it may be desirable for it to automatically reset itself so that
the machine comes back on line. For example, using panic=30 at
boot would cause the kernel to try and reboot itself 30 seconds
after the kernel panic happened. A value of zero gives the default
behaviour, which is to wait forever.
Note that this timeout value can also be read and set via the
/proc/sys/kernel/panic sysctl interface.
Using this option tells a SMP kernel information on the PCI
slot versus IRQ settings for SMP motherboards which are
unknown (or known to be blacklisted).
See linux/Documentation/IO-APIC.txt for more
information.
Kernel developers can
profile how and where the kernel is spending its CPU cycles
in an effort to maximize efficiency and performance. This
option lets you set the profile shift count at boot. Typically
it is set to two. You need a tool such as
readprofile.c that can make use of the /proc/profile
output.
This is pretty much the opposite of the `debug' argument. When this is given, only important and system critical kernel messages are printed to the console. Normal messages about hardware detection at boot are suppressed.
Accepts noautodetect at the moment. See also md=.
This option controls the type of reboot that Linux will do
when it resets the computer (typically via /sbin/init
handling a Control-Alt-Delete). The default as of v2.0
kernels is to do a `cold' reboot (i.e. full reset, BIOS does
memory check, etc.) instead of a `warm' reboot (i.e. no full
reset, no memory check). It was changed to be cold by default
since that tends to work on cheap/broken hardware that fails
to reboot when a warm reboot is requested. To get the old
behaviour (i.e. warm reboots) use reboot=w or in fact
any word that starts with w will work.
Other accepted options are `c', `b', `h', and `s', for cold,
bios, hard, and SMP respectively. The `s' takes an optional
digit to specify which CPU should handle the reboot. Options
can be combined where it makes sense, i.e. reboot=b,s2
This is used to protect I/O port regions from probes. The form of the command is:
reserve=iobase,extent[,iobase,extent]...
In some machines it may be necessary to prevent device drivers from checking for devices (auto-probing) in a specific region. This may be because of poorly designed hardware that causes the boot to freeze (such as some ethercards), hardware that is mistakenly identified, hardware whose state is changed by an earlier probe, or merely hardware you don't want the kernel to initialize.
The reserve boot-time argument addresses this problem by specifying
an I/O port region that shouldn't be probed. That region is reserved
in the kernel's port registration table as if a device has already
been found in that region (with the name reserved).
Note that this mechanism shouldn't be necessary on most machines.
Only when there is a problem or special case would it be necessary
to use this.
The I/O ports in the specified region are protected against
device probes that do a check_region() prior to probing
blindly into a region of I/O space. This was put in to be used
when some driver was hanging on a NE2000, or misidentifying
some other device as its own. A correct device driver shouldn't
probe a reserved region, unless another boot argument explicitly
specifies that it do so. This implies that reserve will
most often be used with some other boot argument. Hence if you
specify a reserve region to protect a specific device, you
must generally specify an explicit probe for that device. Most
drivers ignore the port registration table if they are given an
explicit address.
For example, the boot line
reserve=0x300,32 blah=0x300
keeps all device drivers except the driver for `blah' from
probing 0x300-0x31f.
As usual with boot-time specifiers there is an 11 parameter limit,
thus you can only specify 5 reserved regions per reserve keyword.
Multiple reserve specifiers will work if you have an unusually
complicated request.
If you are using software suspend, then this will allow you to specify the file name of the suspend to disk data that you want the machine to resume from.
Note that this is not really a boot argument. It is an option
that is interpreted by LILO and not by the kernel like all the
other boot arguments are. However its use has become so common
that it deserves a mention here. It can also be set via using
rdev -v or equivalently vidmode on the vmlinuz file.
This allows the setup code to use the video BIOS to change
the default display mode before actually booting the Linux
kernel. Typical modes are 80x50, 132x44 and so on. The best
way to use this option is to start with vga=ask which
will prompt you with a list of various modes that you can use
with your video adapter before booting the kernel. Once you
have the number from the above list that you want to use, you
can later put it in place of the `ask'. For more information,
please see the file linux/Documentation/svga.txt
that comes with all recent kernel versions.
Note that newer kernels (v2.1 and up) have the setup code that
changes the video mode as an option, listed as
Video mode selection support so you need to enable this
option if you want to use this feature.
The `pci=' argument (not avail. in v2.0 kernels)
can be used to change the behaviour of PCI bus device
probing and device behaviour. Firstly the file
linux/drivers/pci/pci.c checks for
architecture independent pci= options.
The remaining allowed arguments are handled
in linux/arch/???/kernel/bios32.c and are
listed below for ???=i386.
This tells the kernel to always assign all PCI bus numbers, overriding whatever the firmware may have done.
These are used to set/clear the flag indicating that the PCI probing is to take place via the PCI BIOS. The default is to use the BIOS.
If PCI direct mode is enabled, the use of these enables either configuration Type 1 or Type 2. These implicitly clear the PCI BIOS probe flag (i.e. `pci=nobios') too.
This allows the user to supply an IRQ mask value, which is converted using strtol(). It will set a bit mask of IRQs allowed to be assigned automatically to PCI devices. You can make the kernel exclude IRQs of your ISA cards this way.
This allows the user to supply a lastbus value, which is converted using strtol(). It will scan all buses till bus N. Can be useful if the kernel is unable to find your secondary buses and you want to tell it explicitly which ones they are.
This disables the use of ACPI routing information during the PCI configuration stages.
This disables the default peer bridge fixup, which according to the source does the following:
``In case there are peer host bridges, scan bus behind each of them. Although several sources claim that the host bridges should have header type 1 and be assigned a bus number as for PCI2PCI bridges, the reality doesn't pass this test and the bus number is usually set by BIOS to the first free value.''
Using this argument instructs the kernel to not sort the PCI devices during the probing phase.
Using this option disables all PCI bus probing. Any device drivers that make use of PCI functions to find and initialize hardware will most likely fail to work.
This sets the USE_PIRQ_MASK flag during PCI init. The kernel will honour the possible IRQ mask stored in the BIOS PIR table. This is needed on some systems with broken BIOSes, notably some HP Pavilion N5400 and Omnibook XE3 notebooks. This will have no effect if ACPI IRQ routing is enabled.
This sets the ASSIGN_ROM flag during the probing phase. The kernel will assign address space to expansion ROMs. Use with caution as certain devices share address decoders between ROMs and other resources.
The `video=' argument (not avail. in v2.0 kernels) is used when the frame buffer device abstraction layer is built into the kernel. If that sounds complicated, well it isn't really too bad. It basically means that instead of having a different video program (the X11R6 server) for each brand of video card (e.g. XF86_S3, XF86_SVGA, ...), the kernel would have a built in driver available for each video card and export a single interface for the video program so that only one X11R6 server (XF86_FBDev) would be required. This is similar to how networking is now - the kernel has drivers available for each brand of network card and exports a single network interface so that just one version of a network program (like Netscape) will work for all systems, regardless of the underlying brand of network card.
The typical format of this argument is
video=name:option1,option2,...
where name is the name of a generic option or of a
frame buffer driver.
The video= option is passed from linux/init/main.c
into linux/drivers/video/fbmem.c for further processing.
Here it is checked for some generic options before trying to
match to a known driver name. Once a driver name match is made,
the comma separated option list is then passed into that particular
driver for final processing. The list of valid driver names
can be found by reading down the fb_drivers array in the
file fbmem.c mentioned above.
Information on the options that each driver supports will
eventually be found in linux/Documentation/fb/ but
currently (v2.2) only a few are described there.
Unfortunately the number
of video drivers and the number of options for each one
is content for another document itself and hence
too much to list here.
If there is no Documentation file for your card, you
will have to get
the option information directly from the driver. Go to
linux/drivers/video/ and look in the appropriate
???fb.c file (the ??? will be based on the card name).
In there, search for a function with _setup in its name
and you should see what options the driver tries to match,
such as font or mode or...
This option is used to set/override the console to frame buffer device mapping. A comma separated list of numbers sets the mapping, with the value of option N taken to be the frame buffer device number for console N.
A number after the colon will set the size of memory allocated for the scrollback buffer. (Use Shift and Page Up or Page Down keys to scroll.) A suffix of `k' or `K' after the number will indicate that the number is to be interpreted as kilobytes instead of bytes.
A number, or a range of numbers (e.g. video=vc:2-5)
will specify the first, or the first and last frame
buffer virtual console(s). The use of this option also
has the effect of setting the frame buffer console to
not be the default console.
This section contains the descriptions of the boot args that are used for passing information about the installed SCSI host adapters, and SCSI devices.
The upper level drivers handle all things SCSI, regardless of whether they be disk, tape, or CD-ROM. The mid level drivers handle things like disks, CD-ROMs and tapes without getting into low level host adapter device driver specifics.
Each SCSI device can have a number of `sub-devices' contained within itself. The most common example is any of the SCSI CD-ROMs that handle more than one disk at a time. Each CD is addressed as a `Logical Unit Number' (LUN) of that particular device. But most devices, such as hard disks, tape drives and such are only one device, and will be assigned to LUN zero.
The problem arises with single LUN devices with bad firmware. Some poorly designed SCSI devices (old and unfortunately new) can not handle being probed for LUNs not equal to zero. They will respond by locking up, and possibly taking the whole SCSI bus down with them.
The kernel has a configuration option that allows you to set the maximum number of probed LUNs. The default is to only probe LUN zero, to avoid the problem described above.
To specify the number of probed LUNs at boot, one enters `max_scsi_luns=n' as a boot arg, where n is a number between one and eight. To avoid problems as described above, one would use n=1 to avoid upsetting such broken devices
Supplying a non-zero value to this boot argument turns on
logging of all SCSI events (error, scan, mlqueue, mlcomplete,
llqueue, llcomplete, hlqueue, hlcomplete). Note that
better control of which events are logged can be obtained
via the /proc/scsi/scsi interface if you aren't
interested in the events that take place at boot before
the /proc/ filesystem is accessible.
Some boot time configuration of the SCSI tape driver can be achieved by using the following:
st=buf_size[,write_threshold[,max_bufs]]
The first two numbers are specified in units of kB.
The default buf_size is 32kB, and the maximum size
that can be specified is a ridiculous 16384kB.
The write_threshold is the value at which the buffer is
committed to tape, with a default value of 30kB.
The maximum number of buffers varies with the number of drives
detected, and has a default of two. An example usage would be:
st=32,30,2
Full details can be found in the README.st file that is
in the scsi directory of the kernel source tree.
These are arguments for low level SCSI host device drivers, and as such are typically only used by those that compile their own kernel with the SCSI driver built in. These people are advised to check the source for the latest list of options that can be supplied to their driver.
aha152x= Adaptec aha151x, aha152x, aic6260, aic6360, SB16-SCSI
aha1542= Adaptec aha1540, aha1542
aic7xxx= Adaptec aha274x, aha284x, aic7xxx
advansys= AdvanSys SCSI Host Adaptors
in2000= Always IN2000 Host Adaptor
AM53C974= AMD AM53C974 based hardware
BusLogic= ISA/PCI/EISA BusLogic SCSI Hosts
eata= EATA SCSI Cards
tmc8xx= Future Domain TMC-8xx, TMC-950
fdomain= Future Domain TMC-16xx, TMC-3260, AHA-2920
ppa= IOMEGA Parallel Port / ZIP drive
ncr5380= NCR5380 based controllers
ncr53c400= NCR53c400 based controllers
ncr53c406a= NCR53c406a based controllers
pas16= Pro Audio Spectrum
st0x= Seagate ST-0x
t128= Trantor T128
u14-34f= Ultrastor SCSI cards
wd7000= Western Digital WD7000 cards
This section lists all the boot args associated with standard MFM/RLL, ST-506, XT, and IDE disk drive devices. Note that both the IDE and the generic ST-506 HD driver both accept the `hd=' option.
The IDE driver accepts a number of parameters, which range
from disk geometry specifications, to support for advanced or
broken controller chips. The following is a summary of
some of the more common boot arguments. For full details, you
really should consult the file ide.txt in the
linux/Documentation directory, from which this
summary was extracted.
"hdx=" is recognized for all "x" from "a" to "h", such as "hdc".
"idex=" is recognized for all "x" from "0" to "3", such as "ide1".
"hdx=noprobe" : drive may be present, but do not probe for it
"hdx=none" : drive is NOT present, ignore cmos and do not probe
"hdx=nowerr" : ignore the WRERR_STAT bit on this drive
"hdx=cdrom" : drive is present, and is a cdrom drive
"hdx=cyl,head,sect" : disk drive is present, with specified geometry
"hdx=autotune" : driver will attempt to tune interface speed
to the fastest PIO mode supported,
if possible for this drive only.
Not fully supported by all chipset types,
and quite likely to cause trouble with
older/odd IDE drives.
"idex=noprobe" : do not attempt to access/use this interface
"idex=base" : probe for an interface at the addr specified,
where "base" is usually 0x1f0 or 0x170
and "ctl" is assumed to be "base"+0x206
"idex=base,ctl" : specify both base and ctl
"idex=base,ctl,irq" : specify base, ctl, and irq number
"idex=autotune" : driver will attempt to tune interface speed
to the fastest PIO mode supported,
for all drives on this interface.
Not fully supported by all chipset types,
and quite likely to cause trouble with
older/odd IDE drives.
"idex=noautotune" : driver will NOT attempt to tune interface speed
This is the default for most chipsets,
except the cmd640.
"idex=serialize" : do not overlap operations on idex and ide(x^1)
The following are valid ONLY on ide0, and the defaults for the base,ctl ports must not be altered.
"ide0=dtc2278" : probe/support DTC2278 interface
"ide0=ht6560b" : probe/support HT6560B interface
"ide0=cmd640_vlb" : *REQUIRED* for VLB cards with the CMD640 chip
(not for PCI -- automatically detected)
"ide0=qd6580" : probe/support qd6580 interface
"ide0=ali14xx" : probe/support ali14xx chipsets (ALI M1439/M1445)
"ide0=umc8672" : probe/support umc8672 chipsets
During the install of some PCMCIA systems, you may be able to get detection of your CD-ROM by using:
"ide2=0x180,0x386" : probe typical PCMCIA IDE interface location
Everything else is rejected with a "BAD OPTION" message.
Also note that there is an implied ide0=0x1f0 ide1=0x170
in the absence of any other ide boot args.
The standard disk driver can accept geometry arguments for the disks similar to the IDE driver. Note however that it only expects three values (C/H/S) -- any more or any less and it will silently ignore you. Also, it only accepts `hd=' as an argument, i.e. `hda=', `hdb=' and so on are not valid here. The format is as follows:
hd=cyls,heads,sects
If there are two disks installed, the above is repeated with the geometry parameters of the second disk.
If you are unfortunate enough to be using one of these old 8 bit cards that move data at a whopping 125kB/s then here is the scoop. The probe code for these cards looks for an installed BIOS, and if none is present, the probe will not find your card. Or, if the signature string of your BIOS is not recognized then it will also not be found. In either case, you will then have to use a boot argument of the form:
xd=type,irq,iobase,dma_chan
The type value specifies the particular manufacturer of the
card, and are as follows: 0=generic; 1=DTC; 2,3,4=Western Digital,
5,6,7=Seagate; 8=OMTI. The only difference between multiple types
from the same manufacturer is the BIOS string used for detection,
which is not used if the type is specified.
The xd_setup() function does no checking on the values, and
assumes that you entered all four values. Don't disappoint it.
Here is an example usage for a WD1002 controller with the BIOS
disabled/removed, using the `default' XT controller parameters:
xd=2,5,0x320,3
If the disk geometry that the kernel prints out comes out all wrong to what you know the disk is set up as, you can override that as well, with:
xd_geo=cyl_xda,head_xda,sec_xda
Add another comma and another three CHS values if you are silly enough to have two disks on the old hunk of scrap...
Note that there was a rewrite of a lot of the sound core and related drivers. The older stuff is generally called `OSS' and the newer is called `ALSA'. The intention is to drop the OSS stuff eventually. To avoid name conflict, the ALSA stuff generally has `snd-' as a prefix to all the boot parameters.
Note that each driver has its own
individual boot argument (very old kernels used a shared
sound=). Also, generally no defaults are set at
compile time (i.e. you must supply a boot
argument for older non-PNP ISA cards to be detected.)
Your best source of information for your card is the files
in linux/Documentation/sound/.
snd-dummy= Dummy soundcard
snd-mpu401= mpu401 UART
snd-mtpav= MOTU Midi Timepiece
snd-serial= Serial UART 16450/16550 MIDI
snd-virmidi= Dummy soundcard for virtual rawmidi devices
snd-ad1816a= ADI SoundPort AD1816A
snd-ad1848= Generic driver for AD1848/AD1847/CS4248
snd-als100= Avance Logic ALS100
snd-azt2320= Aztech Systems AZT2320 (and 2316)
snd-cmi8330= C-Media's CMI8330
snd-cs4231= Generic driver for CS4231 chips
snd-cs4232= Generic driver for CS4232 chips
snd-cs4236= Generic driver for CS4235/6/7/8/9 chips
snd-dt019x= Diamond Technologies DT-019x
snd-es1688= Generic ESS AudioDrive ESx688
snd-es18xx= Generic ESS AudioDrive ES18xx
snd-gusclassic= Gus classic
snd-gusextreme= Gus extreme
snd-gusmax= Gus Max
snd-interwave= Interwave
snd-interwave-stb= Interwave
snd-opl3sa2= Yamaha OPL3SA2
snd-opti93x= OPTi 82c93x based cards
snd-opti92x-cs4231= OPTi 82c92x/CS4231
snd-opti92x-ad1848= OPTi 82c92x/AD1848
snd-es968= ESS AudioDrive ES968
snd-sb16= SoundBlaster 16
snd-sbawe= SoundBlaster 16 AWE
snd-sb8= Old 8 bit SoundBlaster (1.0, 2.0, Pro)
snd-sgalaxy= Sound galaxy
snd-wavefront= Wavefront
ad1848= AD1848
adlib= Adlib
mad16= MAD16
pas2= ProAudioSpectrum PAS16
sb= SoundBlaster
uart401= UART 401 (on card chip)
uart6850= UART 6850 (on card chip)
opl3= Yamaha OPL2/OPL3/OPL4 FM Synthesizer (on card chip)
opl3sa= Yamaha OPL3-SA FM Synthesizer (on card chip)
opl3sa2= Yamaha OPL3-SA2/SA3 FM Synthesizer (on card chip)
snd-ali5451= ALi PCI audio M5451
snd-als4000= Avance Logic ALS4000
snd-cmipci= C-Media CMI8338 and 8738
snd-cs4281= Cirrus Logic CS4281
snd-cs46xx= Cirrus Logic Sound Fusion CS46XX
snd-emu10k1= EMU10K1 (SB Live!)
snd-ens1370= Ensoniq ES1370 AudioPCI
snd-ens1371= Ensoniq ES1371 AudioPCI
snd-es1938= ESS Solo-1 (ES1938, ES1946, ES1969)
snd-es1968= ESS Maestro 1/2/2E
snd-fm801= ForteMedia FM801
snd-intel8x0= Intel ICH (i8x0) chipsets
snd-maestro3= ESS Maestro3/Allegro (ES1988)
snd-korg1212= Korg 1212 IO
snd-rme32= RME Digi32, Digi32/8 and Digi32 PRO
snd-nm256= NeoMagic 256AV and 256ZX
snd-rme96= RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST
snd-rme9652= RME Digi9652 audio interface
snd-hdsp= RME Hammerfall DSP
snd-sonicvibes= S3 SonicVibes
snd-trident= Trident 4DWave DX/NX & SiS SI7018
snd-via82xx= VIA South Bridge VT82C686A/B/C, VT8233A/C, VT8235
snd-ymfpci= Yamaha DS1/DS1E
snd-ice1712= ICEnsemble ICE1712 (Envy24)
This section lists all the possible boot args pertaining to these older CD-ROM devices on proprietary interface cards. Note that this does not include SCSI or IDE/ATAPI CD-ROMs. See the appropriate section(s) for those types of CD-ROMs.
Note that most of these CD-ROMs have documentation files that you
should read, and they are all in one handy place:
linux/Documentation/cdrom.
aztcd= Aztech Interface
cdu31a= CDU-31A and CDU-33A Sony Interface (Also Old PAS)
sonycd535= CDU-535 Sony Interface
gscd= GoldStar Interface
isp16= ISP16 Interface
mcd= Mitsumi Standard Interface
mcdx= Mitsumi XA/MultiSession Interface
optcd= Optics Storage Interface
cm206= Phillips CM206 Interface
sjcd= Sanyo Interface
sbpcd= SoundBlaster Pro Interface
Please see linux/Documentation/isdn/ for the full
details of all the options the following ISDN drivers accept.
icn= ICN ISDN driver
pcbit= PCBIT ISDN driver
teles= Teles ISDN driver
Please see linux/Documentation/ and/or the README
files in linux/drivers/char for the full details of
all the options that the following support.
digi= DigiBoard Driver
riscom8= RISCom/8 Multiport Serial Driver
baycom= Baycom Serial/Parallel Radio Modem
Any other devices that didn't fit into any of the above categories got lumped together here.
Different drivers make use of different parameters, but they all at least share having an IRQ, an I/O port base value, and a name. In its most generic form, it looks something like this:
ether=irq,iobase[,param_1[,param_2,...param_8]]],name
The first non-numeric argument is taken as the name.
The param_n values (if applicable) usually have
different meanings for each different card/driver.
Typical param_n values are used to specify things
like shared memory address, interface selection, DMA
channel and the like.
The most common use of this parameter is to force probing for a second ethercard, as the default is to only probe for one (with 2.4 and older kernels). This can be accomplished with a simple:
ether=0,0,eth1
Note that the values of zero for the IRQ and I/O base in the above example tell the driver(s) to autoprobe.
IMPORTANT NOTE TO MODULE USERS: The above will not force a
probe for a second card if you are using the driver(s) as run time
loadable modules (instead of having them complied into the kernel).
Most Linux distributions use a bare bones kernel combined with a
large selection of modular drivers. The ether= only applies
to drivers compiled directly into the kernel.
The Ethernet-HowTo has complete and extensive
documentation on using multiple cards and on the card/driver
specific implementation of the param_n values where used.
Interested readers should refer to the section in that document
on their particular card for more complete information.
Ethernet-HowTo
There are many floppy driver options, and they are all listed in
floppy.txt in linux/Documentation. There are too
many options in that file to list here. Instead, only those
options that may be required to get a Linux install to proceed
on less than normal hardware are reprinted here.
floppy=0,daring
Tells the floppy driver that your floppy controller should be used
with caution (disables all daring operations).
floppy=thinkpad
Tells the floppy driver that you have a Thinkpad. Thinkpads use an
inverted convention for the disk change line.
floppy=nodma
Tells the floppy driver not to use DMA for data transfers.
This is needed on HP Omnibooks, which don't have a workable
DMA channel for the floppy driver. This option is also useful
if you frequently get `Unable to allocate DMA memory' messages.
Use of `nodma' is not recommended if
you have a FDC without a FIFO (8272A or 82072). 82072A and
later are OK). The FDC model is reported at boot.
You also need at least a 486 to use nodma.
floppy=nofifo
Disables the FIFO entirely. This is needed if you get `Bus
master arbitration error' messages from your Ethernet card (or
from other devices) while accessing the floppy.
floppy=broken_dcl
Don't use the disk change line, but assume that the disk was
changed whenever the device node is reopened. Needed on some
boxes where the disk change line is broken or unsupported.
This should be regarded as a stopgap measure, indeed it makes
floppy operation less efficient due to unneeded cache
flushings, and slightly more unreliable. Please verify your
cable connection and jumper settings if you have any DCL
problems. However, some older drives, and also some Laptops
are known not to have a DCL.
floppy=debug
Print (additional) debugging messages.
floppy=messages
Print informational messages for some operations (disk change
notifications, warnings about over and underruns, and about
autodetection).
The busmouse driver only accepts one parameter, that being the hardware IRQ value to be used.
The MS mouse driver only accepts one parameter, that being the hardware IRQ value to be used.
With this boot argument you can tell the printer driver what ports to use and what ports not to use. The latter comes in handy if you don't want the printer driver to claim all available parallel ports, so that other drivers (e.g. PLIP, PPA) can use them instead.
The format of the argument is multiple i/o, IRQ pairs. For example,
lp=0x3bc,0,0x378,7 would use the port at 0x3bc in IRQ-less
(polling) mode, and use IRQ 7 for the port at 0x378. The port
at 0x278 (if any) would not be probed, since autoprobing only
takes place in the absence of a lp= argument. To disable the
printer driver entirely, one can use lp=0.
Using plip=timid will tell the plip driver to avoid
any ports that appear to be in use by other parallel port
devices. Otherwise you can use plip=parportN where
N is a non-zero integer indicating the parallel
port to use. (Using N=0 will disable the plip driver.)
Hey, you made it to the end! (Phew...) Now just the legal stuff.
This document is Copyright (c) 1995-1999 by Paul Gortmaker. Copying and redistribution is allowed under the conditions as outlined in the Linux Documentation Project Copyright, available from where you obtained this document, OR as outlined in the GNU General Public License, version 2 (see linux/COPYING).
This document is not gospel. However, it is probably the most up to date info that you will be able to find. Nobody is responsible for what happens to your hardware but yourself. If your stuff goes up in smoke, or anything else bad happens, we take no responsibility. ie. THE AUTHOR IS NOT RESPONSIBLE FOR ANY DAMAGES INCURRED DUE TO ACTIONS TAKEN BASED ON THE INFORMATION INCLUDED IN THIS DOCUMENT.
A hint to people considering doing a translation. First,
translate the SGML source (available via FTP from the HowTo
main site) so that you can then generate other output formats.
Be sure to keep a copy of the original English SGML source that
you translated from! When an updated HowTo is released,
get the new SGML source for that version, and then a simple
diff -u old.sgml new.sgml will show you exactly what has
changed so that you can easily incorporate those changes into
your translated SMGL source without having to re-read or
re-translate everything.
If you are intending to incorporate this document into a published work, please make contact (via e-mail) so that you can be supplied with the most up to date information available. In the past, out of date versions of the Linux HowTo documents have been published, which caused the developers undue grief from being plagued with questions that were already answered in the up to date versions.
If you have found any glaring typos, or outdated info in this document, please let me know. It is easy to overlook stuff, as the kernel (and the number of drivers) is huge compared to what it was when I started this.
Thanks,
Paul Gortmaker, p_gortmaker @ yahoo.com