Index: linux/Documentation/cpuidle/core.txt =================================================================== --- /dev/null +++ linux/Documentation/cpuidle/core.txt @@ -0,0 +1,17 @@ + + Supporting multiple CPU idle levels in kernel + + cpuidle + +General Information: + +Various CPUs today support multiple idle levels that are differentiated +by varying exit latencies and power consumption during idle. +cpuidle is a generic in-kernel infrastructure that separates +idle policy (governor) from idle mechanism (driver) and provides a +standardized infrastructure to support independent development of +governors and drivers. + +cpuidle resides under drivers/cpuidle. + + Index: linux/Documentation/cpuidle/driver.txt =================================================================== --- /dev/null +++ linux/Documentation/cpuidle/driver.txt @@ -0,0 +1,29 @@ + + + Supporting multiple CPU idle levels in kernel + + cpuidle drivers + + + + +cpuidle driver hooks into the cpuidle infrastructure and does the +architecture/platform dependent part of CPU idle states. Driver +provides the platform idle state detection capability and also +has mechanisms in place to support actusl entry-exit into a CPU idle state. + +cpuidle driver supports capability detection for a platform using the +init and exit routines. They will be called for each online CPU, with a +percpu cpuidle_driver object and driver should fill in cpuidle_states +inside cpuidle_driver depending on the CPU capability. + +Driver can handle dynamic state changes (like battery<->AC), by calling +force_redetect interface. + +It is possible to have more than one driver registered at the same time and +user can switch between drivers using /sysfs interface (when enabled). + +Interfaces: +int cpuidle_register_driver(struct cpuidle_driver *drv); +void cpuidle_unregister_driver(struct cpuidle_driver *drv); +int cpuidle_force_redetect(struct cpuidle_device *dev); Index: linux/Documentation/cpuidle/governor.txt =================================================================== --- /dev/null +++ linux/Documentation/cpuidle/governor.txt @@ -0,0 +1,28 @@ + + + + Supporting multiple CPU idle levels in kernel + + cpuidle governors + + + + +cpuidle governor is policy routine that decides what idle state to enter at +any given time. cpuidle core uses different callbacks to governor while +handling idle entry. +* select_state() callback where governor can determine next idle state to enter +* prepare_idle() callback is called before entering an idle state +* scan() callback is called after a driver forces redetection of the states + +More than one governor can be registered at the same time and +user can switch between drivers using /sysfs interface (when supported). + +More than one governor part is supported for developers to easily experiment +with different governors. By default, most optimal governor based on your +kernel configuration and platform will be selected by cpuidle. + +Interfaces: +int cpuidle_register_governor(struct cpuidle_governor *gov); +void cpuidle_unregister_governor(struct cpuidle_governor *gov); + Index: linux/Documentation/cpuidle/sysfs.txt =================================================================== --- /dev/null +++ linux/Documentation/cpuidle/sysfs.txt @@ -0,0 +1,35 @@ + + + Supporting multiple CPU idle levels in kernel + + cpuidle sysfs + +System global cpuidle related information and tunables are under +/sys/devices/system/cpu/cpuidle + +The current interfaces in this directory has self-explanatory names: +* current_driver_ro +* current_governor_ro + +With cpuidle_sysfs_switch boot option (meant for developer testing) +following objects are visible instead. +* available_drivers +* available_governors +* current_driver +* current_governor +In this case user can switch the driver, governor at run time by writing +onto current_driver and current_governor. + + +Per logical CPU specific cpuidle information are under +/sys/devices/system/cpu/cpuX/cpuidle +for each online cpu X + +Under this percpu directory, there is a directory for each idle state supported +by the driver, which in turn has +* latency : Latency to exit out of this idle state (in microseconds) +* power : Power consumed while in this idle state (in milliwatts) +* time : Total time spent in this idle state (in microseconds) +* usage : Number of times this state was entered (count) + + Index: linux/Documentation/kernel-parameters.txt =================================================================== --- linux.orig/Documentation/kernel-parameters.txt +++ linux/Documentation/kernel-parameters.txt @@ -1014,49 +1014,6 @@ and is between 256 and 4096 characters. mga= [HW,DRM] - migration_cost= - [KNL,SMP] debug: override scheduler migration costs - Format: ,,... - This debugging option can be used to override the - default scheduler migration cost matrix. The numbers - are indexed by 'CPU domain distance'. - E.g. migration_cost=1000,2000,3000 on an SMT NUMA - box will set up an intra-core migration cost of - 1 msec, an inter-core migration cost of 2 msecs, - and an inter-node migration cost of 3 msecs. - - WARNING: using the wrong values here can break - scheduler performance, so it's only for scheduler - development purposes, not production environments. - - migration_debug= - [KNL,SMP] migration cost auto-detect verbosity - Format=<0|1|2> - If a system's migration matrix reported at bootup - seems erroneous then this option can be used to - increase verbosity of the detection process. - We default to 0 (no extra messages), 1 will print - some more information, and 2 will be really - verbose (probably only useful if you also have a - serial console attached to the system). - - migration_factor= - [KNL,SMP] multiply/divide migration costs by a factor - Format= - This debug option can be used to proportionally - increase or decrease the auto-detected migration - costs for all entries of the migration matrix. - E.g. migration_factor=150 will increase migration - costs by 50%. (and thus the scheduler will be less - eager migrating cache-hot tasks) - migration_factor=80 will decrease migration costs - by 20%. (thus the scheduler will be more eager to - migrate tasks) - - WARNING: using the wrong values here can break - scheduler performance, so it's only for scheduler - development purposes, not production environments. - mousedev.tap_time= [MOUSE] Maximum time between finger touching and leaving touchpad surface for touch to be considered Index: linux/Documentation/sched-design-CFS.txt =================================================================== --- /dev/null +++ linux/Documentation/sched-design-CFS.txt @@ -0,0 +1,119 @@ + +This is the CFS scheduler. + +80% of CFS's design can be summed up in a single sentence: CFS basically +models an "ideal, precise multi-tasking CPU" on real hardware. + +"Ideal multi-tasking CPU" is a (non-existent :-)) CPU that has 100% +physical power and which can run each task at precise equal speed, in +parallel, each at 1/nr_running speed. For example: if there are 2 tasks +running then it runs each at 50% physical power - totally in parallel. + +On real hardware, we can run only a single task at once, so while that +one task runs, the other tasks that are waiting for the CPU are at a +disadvantage - the current task gets an unfair amount of CPU time. In +CFS this fairness imbalance is expressed and tracked via the per-task +p->wait_runtime (nanosec-unit) value. "wait_runtime" is the amount of +time the task should now run on the CPU for it to become completely fair +and balanced. + +( small detail: on 'ideal' hardware, the p->wait_runtime value would + always be zero - no task would ever get 'out of balance' from the + 'ideal' share of CPU time. ) + +CFS's task picking logic is based on this p->wait_runtime value and it +is thus very simple: it always tries to run the task with the largest +p->wait_runtime value. In other words, CFS tries to run the task with +the 'gravest need' for more CPU time. So CFS always tries to split up +CPU time between runnable tasks as close to 'ideal multitasking +hardware' as possible. + +Most of the rest of CFS's design just falls out of this really simple +concept, with a few add-on embellishments like nice levels, +multiprocessing and various algorithm variants to recognize sleepers. + +In practice it works like this: the system runs a task a bit, and when +the task schedules (or a scheduler tick happens) the task's CPU usage is +'accounted for': the (small) time it just spent using the physical CPU +is deducted from p->wait_runtime. [minus the 'fair share' it would have +gotten anyway]. Once p->wait_runtime gets low enough so that another +task becomes the 'leftmost task' of the time-ordered rbtree it maintains +(plus a small amount of 'granularity' distance relative to the leftmost +task so that we do not over-schedule tasks and trash the cache) then the +new leftmost task is picked and the current task is preempted. + +The rq->fair_clock value tracks the 'CPU time a runnable task would have +fairly gotten, had it been runnable during that time'. So by using +rq->fair_clock values we can accurately timestamp and measure the +'expected CPU time' a task should have gotten. All runnable tasks are +sorted in the rbtree by the "rq->fair_clock - p->wait_runtime" key, and +CFS picks the 'leftmost' task and sticks to it. As the system progresses +forwards, newly woken tasks are put into the tree more and more to the +right - slowly but surely giving a chance for every task to become the +'leftmost task' and thus get on the CPU within a deterministic amount of +time. + +Some implementation details: + + - the introduction of Scheduling Classes: an extensible hierarchy of + scheduler modules. These modules encapsulate scheduling policy + details and are handled by the scheduler core without the core + code assuming about them too much. + + - sched_fair.c implements the 'CFS desktop scheduler': it is a + replacement for the vanilla scheduler's SCHED_OTHER interactivity + code. + + I'd like to give credit to Con Kolivas for the general approach here: + he has proven via RSDL/SD that 'fair scheduling' is possible and that + it results in better desktop scheduling. Kudos Con! + + The CFS patch uses a completely different approach and implementation + from RSDL/SD. My goal was to make CFS's interactivity quality exceed + that of RSDL/SD, which is a high standard to meet :-) Testing + feedback is welcome to decide this one way or another. [ and, in any + case, all of SD's logic could be added via a kernel/sched_sd.c module + as well, if Con is interested in such an approach. ] + + CFS's design is quite radical: it does not use runqueues, it uses a + time-ordered rbtree to build a 'timeline' of future task execution, + and thus has no 'array switch' artifacts (by which both the vanilla + scheduler and RSDL/SD are affected). + + CFS uses nanosecond granularity accounting and does not rely on any + jiffies or other HZ detail. Thus the CFS scheduler has no notion of + 'timeslices' and has no heuristics whatsoever. There is only one + central tunable: + + /proc/sys/kernel/sched_granularity_ns + + which can be used to tune the scheduler from 'desktop' (low + latencies) to 'server' (good batching) workloads. It defaults to a + setting suitable for desktop workloads. SCHED_BATCH is handled by the + CFS scheduler module too. + + Due to its design, the CFS scheduler is not prone to any of the + 'attacks' that exist today against the heuristics of the stock + scheduler: fiftyp.c, thud.c, chew.c, ring-test.c, massive_intr.c all + work fine and do not impact interactivity and produce the expected + behavior. + + the CFS scheduler has a much stronger handling of nice levels and + SCHED_BATCH: both types of workloads should be isolated much more + agressively than under the vanilla scheduler. + + ( another detail: due to nanosec accounting and timeline sorting, + sched_yield() support is very simple under CFS, and in fact under + CFS sched_yield() behaves much better than under any other + scheduler i have tested so far. ) + + - sched_rt.c implements SCHED_FIFO and SCHED_RR semantics, in a simpler + way than the vanilla scheduler does. It uses 100 runqueues (for all + 100 RT priority levels, instead of 140 in the vanilla scheduler) + and it needs no expired array. + + - reworked/sanitized SMP load-balancing: the runqueue-walking + assumptions are gone from the load-balancing code now, and + iterators of the scheduling modules are used. The balancing code got + quite a bit simpler as a result. + Index: linux/Documentation/stable_api_nonsense.txt =================================================================== --- linux.orig/Documentation/stable_api_nonsense.txt +++ linux/Documentation/stable_api_nonsense.txt @@ -62,6 +62,9 @@ consider the following facts about the L - different structures can contain different fields - Some functions may not be implemented at all, (i.e. some locks compile away to nothing for non-SMP builds.) + - Parameter passing of variables from function to function can be + done in different ways (the CONFIG_REGPARM option controls + this.) - Memory within the kernel can be aligned in different ways, depending on the build options. - Linux runs on a wide range of different processor architectures. Index: linux/Makefile =================================================================== --- linux.orig/Makefile +++ linux/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 22 -EXTRAVERSION = .1 +EXTRAVERSION = .1-rt1 NAME = Holy Dancing Manatees, Batman! # *DOCUMENTATION* @@ -490,10 +490,14 @@ endif include $(srctree)/arch/$(ARCH)/Makefile -ifdef CONFIG_FRAME_POINTER -CFLAGS += -fno-omit-frame-pointer $(call cc-option,-fno-optimize-sibling-calls,) +ifdef CONFIG_MCOUNT +CFLAGS += -pg -fno-omit-frame-pointer $(call cc-option,-fno-optimize-sibling-calls,) else -CFLAGS += -fomit-frame-pointer + ifdef CONFIG_FRAME_POINTER + CFLAGS += -fno-omit-frame-pointer $(call cc-option,-fno-optimize-sibling-calls,) + else + CFLAGS += -fomit-frame-pointer + endif endif ifdef CONFIG_DEBUG_INFO Index: linux/arch/arm/Kconfig =================================================================== --- linux.orig/arch/arm/Kconfig +++ linux/arch/arm/Kconfig @@ -33,6 +33,10 @@ config GENERIC_CLOCKEVENTS bool default n +config STACKTRACE_SUPPORT + bool + default y + config MMU bool default y @@ -390,7 +394,6 @@ config ARCH_DAVINCI config ARCH_OMAP bool "TI OMAP" select GENERIC_GPIO - select GENERIC_TIME help Support for TI's OMAP platform (OMAP1 and OMAP2). @@ -591,18 +594,7 @@ config LOCAL_TIMERS accounting to be spread across the timer interval, preventing a "thundering herd" at every timer tick. -config PREEMPT - bool "Preemptible Kernel (EXPERIMENTAL)" - depends on EXPERIMENTAL - help - This option reduces the latency of the kernel when reacting to - real-time or interactive events by allowing a low priority process to - be preempted even if it is in kernel mode executing a system call. - This allows applications to run more reliably even when the system is - under load. - - Say Y here if you are building a kernel for a desktop, embedded - or real-time system. Say N if you are unsure. +source kernel/Kconfig.preempt config NO_IDLE_HZ bool "Dynamic tick timer" Index: linux/arch/arm/boot/compressed/head.S =================================================================== --- linux.orig/arch/arm/boot/compressed/head.S +++ linux/arch/arm/boot/compressed/head.S @@ -836,6 +836,18 @@ memdump: mov r12, r0 mov pc, r10 #endif +#ifdef CONFIG_MCOUNT +/* CONFIG_MCOUNT causes boot header to be built with -pg requiring this + * trampoline + */ + .text + .align 0 + .type mcount %function + .global mcount +mcount: + mov pc, lr @ just return +#endif + .ltorg reloc_end: Index: linux/arch/arm/common/time-acorn.c =================================================================== --- linux.orig/arch/arm/common/time-acorn.c +++ linux/arch/arm/common/time-acorn.c @@ -77,7 +77,7 @@ ioc_timer_interrupt(int irq, void *dev_i static struct irqaction ioc_timer_irq = { .name = "timer", - .flags = IRQF_DISABLED, + .flags = IRQF_DISABLED | IRQF_NODELAY, .handler = ioc_timer_interrupt }; Index: linux/arch/arm/kernel/dma.c =================================================================== --- linux.orig/arch/arm/kernel/dma.c +++ linux/arch/arm/kernel/dma.c @@ -20,7 +20,7 @@ #include -DEFINE_SPINLOCK(dma_spin_lock); +DEFINE_RAW_SPINLOCK(dma_spin_lock); EXPORT_SYMBOL(dma_spin_lock); static dma_t dma_chan[MAX_DMA_CHANNELS]; Index: linux/arch/arm/kernel/entry-armv.S =================================================================== --- linux.orig/arch/arm/kernel/entry-armv.S +++ linux/arch/arm/kernel/entry-armv.S @@ -204,7 +204,7 @@ __irq_svc: irq_handler #ifdef CONFIG_PREEMPT ldr r0, [tsk, #TI_FLAGS] @ get flags - tst r0, #_TIF_NEED_RESCHED + tst r0, #_TIF_NEED_RESCHED | _TIF_NEED_RESCHED_DELAYED blne svc_preempt preempt_return: ldr r0, [tsk, #TI_PREEMPT] @ read preempt value @@ -235,7 +235,7 @@ svc_preempt: str r7, [tsk, #TI_PREEMPT] @ expects preempt_count == 0 1: bl preempt_schedule_irq @ irq en/disable is done inside ldr r0, [tsk, #TI_FLAGS] @ get new tasks TI_FLAGS - tst r0, #_TIF_NEED_RESCHED + tst r0, #_TIF_NEED_RESCHED | _TIF_NEED_RESCHED_DELAYED beq preempt_return @ go again b 1b #endif Index: linux/arch/arm/kernel/entry-common.S =================================================================== --- linux.orig/arch/arm/kernel/entry-common.S +++ linux/arch/arm/kernel/entry-common.S @@ -3,6 +3,8 @@ * * Copyright (C) 2000 Russell King * + * FUNCTION_TRACE/mcount support (C) 2005 Timesys john.cooper@timesys.com + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. @@ -44,7 +46,7 @@ ret_fast_syscall: fast_work_pending: str r0, [sp, #S_R0+S_OFF]! @ returned r0 work_pending: - tst r1, #_TIF_NEED_RESCHED + tst r1, #_TIF_NEED_RESCHED | _TIF_NEED_RESCHED_DELAYED bne work_resched tst r1, #_TIF_NOTIFY_RESUME | _TIF_SIGPENDING beq no_work_pending @@ -54,7 +56,8 @@ work_pending: b ret_slow_syscall @ Check work again work_resched: - bl schedule + bl __schedule + /* * "slow" syscall return path. "why" tells us if this was a real syscall. */ @@ -394,6 +397,112 @@ ENTRY(sys_oabi_call_table) #include "calls.S" #undef ABI #undef OBSOLETE +#endif + +#ifdef CONFIG_FRAME_POINTER + +#ifdef CONFIG_MCOUNT +/* + * At the point where we are in mcount() we maintain the + * frame of the prologue code and keep the call to mcount() + * out of the stack frame list: + + saved pc <---\ caller of instrumented routine + saved lr | + ip/prev_sp | + fp -----^ | + : | + | + -> saved pc | instrumented routine + | saved lr | + | ip/prev_sp | + | fp ---------/ + | : + | + | mcount + | saved pc + | saved lr + | ip/prev sp + -- fp + r3 + r2 + r1 + sp-> r0 + : + */ + + .text + .align 0 + .type mcount %function + .global mcount + +/* gcc -pg generated FUNCTION_PROLOGUE references mcount() + * and has already created the stack frame invocation for + * the routine we have been called to instrument. We create + * a complete frame nevertheless, as we want to use the same + * call to mcount() from c code. + */ +mcount: + + ldr ip, =mcount_enabled @ leave early, if disabled + ldr ip, [ip] + cmp ip, #0 + moveq pc, lr + + mov ip, sp + stmdb sp!, {r0 - r3, fp, ip, lr, pc} @ create stack frame + + ldr r1, [fp, #-4] @ get lr (the return address + @ of the caller of the + @ instrumented function) + mov r0, lr @ get lr - (the return address + @ of the instrumented function) + + sub fp, ip, #4 @ point fp at this frame + + bl __trace +1: + ldmdb fp, {r0 - r3, fp, sp, pc} @ pop entry frame and return + +#endif + +/* ARM replacement for unsupported gcc __builtin_return_address(n) + * where 0 < n. n == 0 is supported here as well. + * + * Walk up the stack frame until the desired frame is found or a NULL + * fp is encountered, return NULL in the latter case. + * + * Note: it is possible under code optimization for the stack invocation + * of an ancestor function (level N) to be removed before calling a + * descendant function (level N+1). No easy means is available to deduce + * this scenario with the result being [for example] caller_addr(0) when + * called from level N+1 returning level N-1 rather than the expected + * level N. This optimization issue appears isolated to the case of + * a call to a level N+1 routine made at the tail end of a level N + * routine -- the level N frame is deleted and a simple branch is made + * to the level N+1 routine. + */ + + .text + .align 0 + .type arm_return_addr %function + .global arm_return_addr + +arm_return_addr: + mov ip, r0 + mov r0, fp +3: + cmp r0, #0 + beq 1f @ frame list hit end, bail + cmp ip, #0 + beq 2f @ reached desired frame + ldr r0, [r0, #-12] @ else continue, get next fp + sub ip, ip, #1 + b 3b +2: + ldr r0, [r0, #-4] @ get target return address +1: + mov pc, lr #endif Index: linux/arch/arm/kernel/fiq.c =================================================================== --- linux.orig/arch/arm/kernel/fiq.c +++ linux/arch/arm/kernel/fiq.c @@ -89,7 +89,7 @@ void set_fiq_handler(void *start, unsign * disable irqs for the duration. Note - these functions are almost * entirely coded in assembly. */ -void __attribute__((naked)) set_fiq_regs(struct pt_regs *regs) +void notrace __attribute__((naked)) set_fiq_regs(struct pt_regs *regs) { register unsigned long tmp; asm volatile ( @@ -107,7 +107,7 @@ void __attribute__((naked)) set_fiq_regs : "r" (®s->ARM_r8), "I" (PSR_I_BIT | PSR_F_BIT | FIQ_MODE)); } -void __attribute__((naked)) get_fiq_regs(struct pt_regs *regs) +void notrace __attribute__((naked)) get_fiq_regs(struct pt_regs *regs) { register unsigned long tmp; asm volatile ( Index: linux/arch/arm/kernel/irq.c =================================================================== --- linux.orig/arch/arm/kernel/irq.c +++ linux/arch/arm/kernel/irq.c @@ -100,7 +100,7 @@ unlock: /* Handle bad interrupts */ static struct irq_desc bad_irq_desc = { .handle_irq = handle_bad_irq, - .lock = SPIN_LOCK_UNLOCKED + .lock = RAW_SPIN_LOCK_UNLOCKED(bad_irq_desc.lock) }; /* @@ -108,11 +108,14 @@ static struct irq_desc bad_irq_desc = { * come via this function. Instead, they should provide their * own 'handler' */ -asmlinkage void __exception asm_do_IRQ(unsigned int irq, struct pt_regs *regs) +asmlinkage void __exception notrace asm_do_IRQ(unsigned int irq, + struct pt_regs *regs) { struct pt_regs *old_regs = set_irq_regs(regs); struct irq_desc *desc = irq_desc + irq; + trace_special(instruction_pointer(regs), irq, 0); + /* * Some hardware gives randomly wrong interrupts. Rather * than crashing, do something sensible. Index: linux/arch/arm/kernel/process.c =================================================================== --- linux.orig/arch/arm/kernel/process.c +++ linux/arch/arm/kernel/process.c @@ -130,7 +130,7 @@ static void default_idle(void) cpu_relax(); else { local_irq_disable(); - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { timer_dyn_reprogram(); arch_idle(); } @@ -162,13 +162,15 @@ void cpu_idle(void) idle = default_idle; leds_event(led_idle_start); tick_nohz_stop_sched_tick(); - while (!need_resched()) + while (!need_resched() && !need_resched_delayed()) idle(); leds_event(led_idle_end); tick_nohz_restart_sched_tick(); - preempt_enable_no_resched(); - schedule(); + local_irq_disable(); + __preempt_enable_no_resched(); + __schedule(); preempt_disable(); + local_irq_enable(); } } Index: linux/arch/arm/kernel/semaphore.c =================================================================== --- linux.orig/arch/arm/kernel/semaphore.c +++ linux/arch/arm/kernel/semaphore.c @@ -49,14 +49,16 @@ * we cannot lose wakeup events. */ -void __up(struct semaphore *sem) +fastcall void __attribute_used__ __compat_up(struct compat_semaphore *sem) { wake_up(&sem->wait); } +EXPORT_SYMBOL(__compat_up); + static DEFINE_SPINLOCK(semaphore_lock); -void __sched __down(struct semaphore * sem) +fastcall void __attribute_used__ __sched __compat_down(struct compat_semaphore * sem) { struct task_struct *tsk = current; DECLARE_WAITQUEUE(wait, tsk); @@ -89,7 +91,9 @@ void __sched __down(struct semaphore * s wake_up(&sem->wait); } -int __sched __down_interruptible(struct semaphore * sem) +EXPORT_SYMBOL(__compat_down); + +fastcall int __attribute_used__ __sched __compat_down_interruptible(struct compat_semaphore * sem) { int retval = 0; struct task_struct *tsk = current; @@ -140,6 +144,8 @@ int __sched __down_interruptible(struct return retval; } +EXPORT_SYMBOL(__compat_down_interruptible); + /* * Trylock failed - make sure we correct for * having decremented the count. @@ -148,7 +154,7 @@ int __sched __down_interruptible(struct * single "cmpxchg" without failure cases, * but then it wouldn't work on a 386. */ -int __down_trylock(struct semaphore * sem) +fastcall int __attribute_used__ __sched __compat_down_trylock(struct compat_semaphore * sem) { int sleepers; unsigned long flags; @@ -168,6 +174,15 @@ int __down_trylock(struct semaphore * se return 1; } +EXPORT_SYMBOL(__compat_down_trylock); + +fastcall int __sched compat_sem_is_locked(struct compat_semaphore *sem) +{ + return (int) atomic_read(&sem->count) < 0; +} + +EXPORT_SYMBOL(compat_sem_is_locked); + /* * The semaphore operations have a special calling sequence that * allow us to do a simpler in-line version of them. These routines @@ -185,7 +200,7 @@ asm(" .section .sched.text,\"ax\",%progb __down_failed: \n\ stmfd sp!, {r0 - r4, lr} \n\ mov r0, ip \n\ - bl __down \n\ + bl __compat_down \n\ ldmfd sp!, {r0 - r4, pc} \n\ \n\ .align 5 \n\ @@ -193,7 +208,7 @@ __down_failed: \n\ __down_interruptible_failed: \n\ stmfd sp!, {r0 - r4, lr} \n\ mov r0, ip \n\ - bl __down_interruptible \n\ + bl __compat_down_interruptible \n\ mov ip, r0 \n\ ldmfd sp!, {r0 - r4, pc} \n\ \n\ @@ -202,7 +217,7 @@ __down_interruptible_failed: \n\ __down_trylock_failed: \n\ stmfd sp!, {r0 - r4, lr} \n\ mov r0, ip \n\ - bl __down_trylock \n\ + bl __compat_down_trylock \n\ mov ip, r0 \n\ ldmfd sp!, {r0 - r4, pc} \n\ \n\ @@ -211,7 +226,7 @@ __down_trylock_failed: \n\ __up_wakeup: \n\ stmfd sp!, {r0 - r4, lr} \n\ mov r0, ip \n\ - bl __up \n\ + bl __compat_up \n\ ldmfd sp!, {r0 - r4, pc} \n\ "); Index: linux/arch/arm/kernel/signal.c =================================================================== --- linux.orig/arch/arm/kernel/signal.c +++ linux/arch/arm/kernel/signal.c @@ -623,6 +623,14 @@ static int do_signal(sigset_t *oldset, s siginfo_t info; int signr; +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + local_irq_enable(); + preempt_check_resched(); +#endif + /* * We want the common case to go fast, which * is why we may in certain cases get here from Index: linux/arch/arm/kernel/smp.c =================================================================== --- linux.orig/arch/arm/kernel/smp.c +++ linux/arch/arm/kernel/smp.c @@ -521,7 +521,7 @@ static void ipi_call_function(unsigned i cpu_clear(cpu, data->unfinished); } -static DEFINE_SPINLOCK(stop_lock); +static DEFINE_RAW_SPINLOCK(stop_lock); /* * ipi_cpu_stop - handle IPI from smp_send_stop() Index: linux/arch/arm/kernel/time.c =================================================================== --- linux.orig/arch/arm/kernel/time.c +++ linux/arch/arm/kernel/time.c @@ -236,6 +236,13 @@ static inline void do_leds(void) #define do_leds() #endif +void arch_tick_leds(void) +{ +#ifdef CONFIG_LEDS_TIMER + do_leds(); +#endif +} + #ifndef CONFIG_GENERIC_TIME void do_gettimeofday(struct timeval *tv) { Index: linux/arch/arm/kernel/traps.c =================================================================== --- linux.orig/arch/arm/kernel/traps.c +++ linux/arch/arm/kernel/traps.c @@ -182,6 +182,7 @@ static void dump_backtrace(struct pt_reg void dump_stack(void) { __backtrace(); + print_traces(current); } EXPORT_SYMBOL(dump_stack); @@ -233,7 +234,7 @@ static void __die(const char *str, int e } } -DEFINE_SPINLOCK(die_lock); +DEFINE_RAW_SPINLOCK(die_lock); /* * This function is protected against re-entrancy. @@ -275,7 +276,7 @@ void arm_notify_die(const char *str, str } static LIST_HEAD(undef_hook); -static DEFINE_SPINLOCK(undef_lock); +static DEFINE_RAW_SPINLOCK(undef_lock); void register_undef_hook(struct undef_hook *hook) { Index: linux/arch/arm/lib/Makefile =================================================================== --- linux.orig/arch/arm/lib/Makefile +++ linux/arch/arm/lib/Makefile @@ -41,6 +41,7 @@ lib-$(CONFIG_ARCH_RPC) += ecard.o io-ac lib-$(CONFIG_ARCH_CLPS7500) += io-acorn.o lib-$(CONFIG_ARCH_L7200) += io-acorn.o lib-$(CONFIG_ARCH_SHARK) += io-shark.o +lib-$(CONFIG_STACKTRACE) += stacktrace.o $(obj)/csumpartialcopy.o: $(obj)/csumpartialcopygeneric.S $(obj)/csumpartialcopyuser.o: $(obj)/csumpartialcopygeneric.S Index: linux/arch/arm/lib/stacktrace.c =================================================================== --- /dev/null +++ linux/arch/arm/lib/stacktrace.c @@ -0,0 +1,7 @@ +#include +#include + +void save_stack_trace(struct stack_trace *trace, struct task_struct *task) +{ +} + Index: linux/arch/arm/mach-ep93xx/core.c =================================================================== --- linux.orig/arch/arm/mach-ep93xx/core.c +++ linux/arch/arm/mach-ep93xx/core.c @@ -32,6 +32,8 @@ #include #include #include +#include +#include #include #include @@ -50,7 +52,6 @@ #include - /************************************************************************* * Static I/O mappings that are needed for all EP93xx platforms *************************************************************************/ @@ -93,59 +94,125 @@ void __init ep93xx_map_io(void) * to use this timer for something else. We also use timer 4 for keeping * track of lost jiffies. */ -static unsigned int last_jiffy_time; - -#define TIMER4_TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ) +static struct clock_event_device clockevent_ep93xx; static int ep93xx_timer_interrupt(int irq, void *dev_id) { - write_seqlock(&xtime_lock); + __raw_writel(EP93XX_TC_CLEAR, EP93XX_TIMER1_CLEAR); - __raw_writel(1, EP93XX_TIMER1_CLEAR); - while ((signed long) - (__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time) - >= TIMER4_TICKS_PER_JIFFY) { - last_jiffy_time += TIMER4_TICKS_PER_JIFFY; - timer_tick(); - } - - write_sequnlock(&xtime_lock); + clockevent_ep93xx.event_handler(&clockevent_ep93xx); return IRQ_HANDLED; } +static int ep93xx_set_next_event(unsigned long evt, + struct clock_event_device *unused) +{ + u32 tmode = __raw_readl(EP93XX_TIMER1_CONTROL); + + /* stop timer */ + __raw_writel(tmode & ~EP93XX_TC123_ENABLE, EP93XX_TIMER1_CONTROL); + /* program timer */ + __raw_writel(evt, EP93XX_TIMER1_LOAD); + /* start timer */ + __raw_writel(tmode | EP93XX_TC123_ENABLE, EP93XX_TIMER1_CONTROL); + + return 0; +} + +static void ep93xx_set_mode(enum clock_event_mode mode, + struct clock_event_device *evt) +{ + u32 tmode = EP93XX_TC123_SEL_508KHZ; + + /* Disable timer */ + __raw_writel(tmode, EP93XX_TIMER1_CONTROL); + + switch(mode) { + case CLOCK_EVT_MODE_PERIODIC: + /* Set timer period */ + __raw_writel((508469 / HZ) - 1, EP93XX_TIMER1_LOAD); + tmode |= EP93XX_TC123_PERIODIC; + + case CLOCK_EVT_MODE_ONESHOT: + tmode |= EP93XX_TC123_ENABLE; + __raw_writel(tmode, EP93XX_TIMER1_CONTROL); + break; + + case CLOCK_EVT_MODE_SHUTDOWN: + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_RESUME: + return; + } +} + +static struct clock_event_device clockevent_ep93xx = { + .name = "ep93xx-timer1", + .features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC, + .shift = 32, + .set_mode = ep93xx_set_mode, + .set_next_event = ep93xx_set_next_event, +}; + + static struct irqaction ep93xx_timer_irq = { .name = "ep93xx timer", .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, .handler = ep93xx_timer_interrupt, }; -static void __init ep93xx_timer_init(void) +static void __init ep93xx_clockevent_init(void) { - /* Enable periodic HZ timer. */ - __raw_writel(0x48, EP93XX_TIMER1_CONTROL); - __raw_writel((508469 / HZ) - 1, EP93XX_TIMER1_LOAD); - __raw_writel(0xc8, EP93XX_TIMER1_CONTROL); + setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq); - /* Enable lost jiffy timer. */ - __raw_writel(0x100, EP93XX_TIMER4_VALUE_HIGH); + clockevent_ep93xx.mult = div_sc(508469, NSEC_PER_SEC, + clockevent_ep93xx.shift); + clockevent_ep93xx.max_delta_ns = + clockevent_delta2ns(0xfffffffe, &clockevent_ep93xx); + clockevent_ep93xx.min_delta_ns = + clockevent_delta2ns(0xf, &clockevent_ep93xx); + clockevent_ep93xx.cpumask = cpumask_of_cpu(0); + clockevents_register_device(&clockevent_ep93xx); +} - setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq); +/* + * timer4 is a 40 Bit timer, separated in a 32bit and a 8 bit + * register, EP93XX_TIMER4_VALUE_LOW stores 32 bit word. The + * controlregister is in EP93XX_TIMER4_VALUE_HIGH + */ + +cycle_t ep93xx_get_cycles(void) +{ + return __raw_readl(EP93XX_TIMER4_VALUE_LOW); } -static unsigned long ep93xx_gettimeoffset(void) +static struct clocksource clocksource_ep93xx = { + .name = "ep93xx_timer4", + .rating = 200, + .read = ep93xx_get_cycles, + .mask = 0xFFFFFFFF, + .shift = 20, + .flags = CLOCK_SOURCE_IS_CONTINUOUS, +}; + +static void __init ep93xx_clocksource_init(void) { - int offset; + /* Reset time-stamp counter */ + __raw_writel(0x100, EP93XX_TIMER4_VALUE_HIGH); - offset = __raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time; + clocksource_ep93xx.mult = + clocksource_hz2mult(983040, clocksource_ep93xx.shift); + clocksource_register(&clocksource_ep93xx); +} - /* Calculate (1000000 / 983040) * offset. */ - return offset + (53 * offset / 3072); +static void __init ep93xx_timer_init(void) +{ + ep93xx_clocksource_init(); + ep93xx_clockevent_init(); } struct sys_timer ep93xx_timer = { - .init = ep93xx_timer_init, - .offset = ep93xx_gettimeoffset, + .init = ep93xx_timer_init, }; @@ -497,7 +564,6 @@ static struct platform_device ep93xx_ohc .resource = ep93xx_ohci_resources, }; - void __init ep93xx_init_devices(void) { unsigned int v; Index: linux/arch/arm/mach-footbridge/netwinder-hw.c =================================================================== --- linux.orig/arch/arm/mach-footbridge/netwinder-hw.c +++ linux/arch/arm/mach-footbridge/netwinder-hw.c @@ -67,7 +67,7 @@ static inline void wb977_ww(int reg, int /* * This is a lock for accessing ports GP1_IO_BASE and GP2_IO_BASE */ -DEFINE_SPINLOCK(gpio_lock); +DEFINE_RAW_SPINLOCK(gpio_lock); static unsigned int current_gpio_op; static unsigned int current_gpio_io; Index: linux/arch/arm/mach-footbridge/netwinder-leds.c =================================================================== --- linux.orig/arch/arm/mach-footbridge/netwinder-leds.c +++ linux/arch/arm/mach-footbridge/netwinder-leds.c @@ -32,7 +32,7 @@ static char led_state; static char hw_led_state; static DEFINE_SPINLOCK(leds_lock); -extern spinlock_t gpio_lock; +extern raw_spinlock_t gpio_lock; static void netwinder_leds_event(led_event_t evt) { Index: linux/arch/arm/mach-imx/time.c =================================================================== --- linux.orig/arch/arm/mach-imx/time.c +++ linux/arch/arm/mach-imx/time.c @@ -3,6 +3,7 @@ * * Copyright (C) 2000-2001 Deep Blue Solutions * Copyright (C) 2002 Shane Nay (shane@minirl.com) + * Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -15,6 +16,7 @@ #include #include #include +#include #include #include @@ -25,7 +27,8 @@ /* Use timer 1 as system timer */ #define TIMER_BASE IMX_TIM1_BASE -static unsigned long evt_diff; +static struct clock_event_device clockevent_imx; +static enum clock_event_mode clockevent_mode = CLOCK_EVT_MODE_UNUSED; /* * IRQ handler for the timer @@ -33,25 +36,20 @@ static unsigned long evt_diff; static irqreturn_t imx_timer_interrupt(int irq, void *dev_id) { + struct clock_event_device *evt = &clockevent_imx; uint32_t tstat; + irqreturn_t ret = IRQ_NONE; /* clear the interrupt */ tstat = IMX_TSTAT(TIMER_BASE); IMX_TSTAT(TIMER_BASE) = 0; if (tstat & TSTAT_COMP) { - do { - - write_seqlock(&xtime_lock); - timer_tick(); - write_sequnlock(&xtime_lock); - IMX_TCMP(TIMER_BASE) += evt_diff; - - } while (unlikely((int32_t)(IMX_TCMP(TIMER_BASE) - - IMX_TCN(TIMER_BASE)) < 0)); + evt->event_handler(evt); + ret = IRQ_HANDLED; } - return IRQ_HANDLED; + return ret; } static struct irqaction imx_timer_irq = { @@ -70,10 +68,8 @@ static void __init imx_timer_hardware_in */ IMX_TCTL(TIMER_BASE) = 0; IMX_TPRER(TIMER_BASE) = 0; - IMX_TCMP(TIMER_BASE) = LATCH - 1; - IMX_TCTL(TIMER_BASE) = TCTL_FRR | TCTL_CLK_PCLK1 | TCTL_IRQEN | TCTL_TEN; - evt_diff = LATCH; + IMX_TCTL(TIMER_BASE) = TCTL_FRR | TCTL_CLK_PCLK1 | TCTL_TEN; } cycle_t imx_get_cycles(void) @@ -99,11 +95,108 @@ static int __init imx_clocksource_init(v return 0; } +static int imx_set_next_event(unsigned long evt, + struct clock_event_device *unused) +{ + unsigned long tcmp; + + tcmp = IMX_TCN(TIMER_BASE) + evt; + IMX_TCMP(TIMER_BASE) = tcmp; + + return (int32_t)(tcmp - IMX_TCN(TIMER_BASE)) < 0 ? -ETIME : 0; +} + +#ifdef DEBUG +static const char *clock_event_mode_label[]={ + [CLOCK_EVT_MODE_PERIODIC] = "CLOCK_EVT_MODE_PERIODIC", + [CLOCK_EVT_MODE_ONESHOT] = "CLOCK_EVT_MODE_ONESHOT", + [CLOCK_EVT_MODE_SHUTDOWN] = "CLOCK_EVT_MODE_SHUTDOWN", + [CLOCK_EVT_MODE_UNUSED] = "CLOCK_EVT_MODE_UNUSED" +}; +#endif /*DEBUG*/ + +static void imx_set_mode(enum clock_event_mode mode, struct clock_event_device *evt) +{ + unsigned long flags; + + /* + * The timer interrupt generation is disabled at least + * for enough time to call imx_set_next_event() + */ + local_irq_save(flags); + /* Disable interrupt in GPT module */ + IMX_TCTL(TIMER_BASE) &= ~TCTL_IRQEN; + if (mode != clockevent_mode) { + /* Set event time into far-far future */ + IMX_TCMP(TIMER_BASE) = IMX_TCN(TIMER_BASE) - 3; + /* Clear pending interrupt */ + IMX_TSTAT(TIMER_BASE) &= ~TSTAT_COMP; + } + +#ifdef DEBUG + printk(KERN_INFO "imx_set_mode: changing mode from %s to %s\n", + clock_event_mode_label[clockevent_mode], clock_event_mode_label[mode]); +#endif /*DEBUG*/ + + /* Remember timer mode */ + clockevent_mode = mode; + local_irq_restore(flags); + + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + printk(KERN_ERR "imx_set_mode: Periodic mode is not supported for i.MX\n"); + break; + case CLOCK_EVT_MODE_ONESHOT: + /* + * Do not put overhead of interrupt enable/disable into + * imx_set_next_event(), the core has about 4 minutes + * to call imx_set_next_event() or shutdown clock after + * mode switching + */ + local_irq_save(flags); + IMX_TCTL(TIMER_BASE) |= TCTL_IRQEN; + local_irq_restore(flags); + break; + case CLOCK_EVT_MODE_SHUTDOWN: + case CLOCK_EVT_MODE_UNUSED: + /* Left event sources disabled, no more interrupts appears */ + break; + } +} + +static struct clock_event_device clockevent_imx = { + .name = "imx_timer1", + .features = CLOCK_EVT_FEAT_ONESHOT, + .shift = 32, + .set_mode = imx_set_mode, + .set_next_event = imx_set_next_event, + .rating = 200, +}; + +static int __init imx_clockevent_init(void) +{ + clockevent_imx.mult = div_sc(imx_get_perclk1(), NSEC_PER_SEC, + clockevent_imx.shift); + clockevent_imx.max_delta_ns = + clockevent_delta2ns(0xfffffffe, &clockevent_imx); + clockevent_imx.min_delta_ns = + clockevent_delta2ns(0xf, &clockevent_imx); + + clockevent_imx.cpumask = cpumask_of_cpu(0); + + clockevents_register_device(&clockevent_imx); + + return 0; +} + + static void __init imx_timer_init(void) { imx_timer_hardware_init(); imx_clocksource_init(); + imx_clockevent_init(); + /* * Make irqs happen for the system timer */ Index: linux/arch/arm/mach-integrator/core.c =================================================================== --- linux.orig/arch/arm/mach-integrator/core.c +++ linux/arch/arm/mach-integrator/core.c @@ -164,7 +164,7 @@ static struct amba_pl010_data integrator #define CM_CTRL IO_ADDRESS(INTEGRATOR_HDR_BASE) + INTEGRATOR_HDR_CTRL_OFFSET -static DEFINE_SPINLOCK(cm_lock); +static DEFINE_RAW_SPINLOCK(cm_lock); /** * cm_control - update the CM_CTRL register. Index: linux/arch/arm/mach-integrator/pci_v3.c =================================================================== --- linux.orig/arch/arm/mach-integrator/pci_v3.c +++ linux/arch/arm/mach-integrator/pci_v3.c @@ -162,7 +162,7 @@ * 7:2 register number * */ -static DEFINE_SPINLOCK(v3_lock); +static DEFINE_RAW_SPINLOCK(v3_lock); #define PCI_BUS_NONMEM_START 0x00000000 #define PCI_BUS_NONMEM_SIZE SZ_256M Index: linux/arch/arm/mach-ixp4xx/common-pci.c =================================================================== --- linux.orig/arch/arm/mach-ixp4xx/common-pci.c +++ linux/arch/arm/mach-ixp4xx/common-pci.c @@ -53,7 +53,7 @@ unsigned long ixp4xx_pci_reg_base = 0; * these transactions are atomic or we will end up * with corrupt data on the bus or in a driver. */ -static DEFINE_SPINLOCK(ixp4xx_pci_lock); +static DEFINE_RAW_SPINLOCK(ixp4xx_pci_lock); /* * Read from PCI config space Index: linux/arch/arm/mach-sa1100/badge4.c =================================================================== --- linux.orig/arch/arm/mach-sa1100/badge4.c +++ linux/arch/arm/mach-sa1100/badge4.c @@ -240,15 +240,22 @@ void badge4_set_5V(unsigned subsystem, i /* detect on->off and off->on transitions */ if ((!old_5V_bitmap) && (badge4_5V_bitmap)) { /* was off, now on */ - printk(KERN_INFO "%s: enabling 5V supply rail\n", __FUNCTION__); GPSR = BADGE4_GPIO_PCMEN5V; } else if ((old_5V_bitmap) && (!badge4_5V_bitmap)) { /* was on, now off */ - printk(KERN_INFO "%s: disabling 5V supply rail\n", __FUNCTION__); GPCR = BADGE4_GPIO_PCMEN5V; } local_irq_restore(flags); + + /* detect on->off and off->on transitions */ + if ((!old_5V_bitmap) && (badge4_5V_bitmap)) { + /* was off, now on */ + printk(KERN_INFO "%s: enabling 5V supply rail\n", __FUNCTION__); + } else if ((old_5V_bitmap) && (!badge4_5V_bitmap)) { + /* was on, now off */ + printk(KERN_INFO "%s: disabling 5V supply rail\n", __FUNCTION__); + } } EXPORT_SYMBOL(badge4_set_5V); Index: linux/arch/arm/mach-shark/leds.c =================================================================== --- linux.orig/arch/arm/mach-shark/leds.c +++ linux/arch/arm/mach-shark/leds.c @@ -32,7 +32,7 @@ static char led_state; static short hw_led_state; static short saved_state; -static DEFINE_SPINLOCK(leds_lock); +static DEFINE_RAW_SPINLOCK(leds_lock); short sequoia_read(int addr) { outw(addr,0x24); Index: linux/arch/arm/mm/consistent.c =================================================================== --- linux.orig/arch/arm/mm/consistent.c +++ linux/arch/arm/mm/consistent.c @@ -40,7 +40,7 @@ * These are the page tables (2MB each) covering uncached, DMA consistent allocations */ static pte_t *consistent_pte[NUM_CONSISTENT_PTES]; -static DEFINE_SPINLOCK(consistent_lock); +static DEFINE_RAW_SPINLOCK(consistent_lock); /* * VM region handling support. Index: linux/arch/arm/mm/copypage-v4mc.c =================================================================== --- linux.orig/arch/arm/mm/copypage-v4mc.c +++ linux/arch/arm/mm/copypage-v4mc.c @@ -30,7 +30,7 @@ #define minicache_pgprot __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | \ L_PTE_CACHEABLE) -static DEFINE_SPINLOCK(minicache_lock); +static DEFINE_RAW_SPINLOCK(minicache_lock); /* * ARMv4 mini-dcache optimised copy_user_page @@ -44,7 +44,7 @@ static DEFINE_SPINLOCK(minicache_lock); * instruction. If your processor does not supply this, you have to write your * own copy_user_page that does the right thing. */ -static void __attribute__((naked)) +static void notrace __attribute__((naked)) mc_copy_user_page(void *from, void *to) { asm volatile( @@ -88,7 +88,7 @@ void v4_mc_copy_user_page(void *kto, con /* * ARMv4 optimised clear_user_page */ -void __attribute__((naked)) +void notrace __attribute__((naked)) v4_mc_clear_user_page(void *kaddr, unsigned long vaddr) { asm volatile( Index: linux/arch/arm/mm/copypage-v6.c =================================================================== --- linux.orig/arch/arm/mm/copypage-v6.c +++ linux/arch/arm/mm/copypage-v6.c @@ -26,7 +26,7 @@ #define from_address (0xffff8000) #define to_address (0xffffc000) -static DEFINE_SPINLOCK(v6_lock); +static DEFINE_RAW_SPINLOCK(v6_lock); /* * Copy the user page. No aliasing to deal with so we can just Index: linux/arch/arm/mm/copypage-xscale.c =================================================================== --- linux.orig/arch/arm/mm/copypage-xscale.c +++ linux/arch/arm/mm/copypage-xscale.c @@ -32,7 +32,7 @@ #define minicache_pgprot __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | \ L_PTE_CACHEABLE) -static DEFINE_SPINLOCK(minicache_lock); +static DEFINE_RAW_SPINLOCK(minicache_lock); /* * XScale mini-dcache optimised copy_user_page @@ -42,7 +42,7 @@ static DEFINE_SPINLOCK(minicache_lock); * Dcache aliasing issue. The writes will be forwarded to the write buffer, * and merged as appropriate. */ -static void __attribute__((naked)) +static void notrace __attribute__((naked)) mc_copy_user_page(void *from, void *to) { /* @@ -110,7 +110,7 @@ void xscale_mc_copy_user_page(void *kto, /* * XScale optimised clear_user_page */ -void __attribute__((naked)) +void notrace __attribute__((naked)) xscale_mc_clear_user_page(void *kaddr, unsigned long vaddr) { asm volatile( Index: linux/arch/arm/mm/fault.c =================================================================== --- linux.orig/arch/arm/mm/fault.c +++ linux/arch/arm/mm/fault.c @@ -215,7 +215,7 @@ out: return fault; } -static int +static notrace int do_page_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs) { struct task_struct *tsk; @@ -229,7 +229,7 @@ do_page_fault(unsigned long addr, unsign * If we're in an interrupt or have no user * context, we must not take the fault.. */ - if (in_atomic() || !mm) + if (in_atomic() || !mm || current->pagefault_disabled) goto no_context; /* @@ -315,7 +315,7 @@ no_context: * interrupt or a critical region, and should only copy the information * from the master page table, nothing more. */ -static int +static notrace int do_translation_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs) { @@ -358,7 +358,7 @@ bad_area: * Some section permission faults need to be handled gracefully. * They can happen due to a __{get,put}_user during an oops. */ -static int +static notrace int do_sect_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs) { do_bad_area(addr, fsr, regs); @@ -368,7 +368,7 @@ do_sect_fault(unsigned long addr, unsign /* * This abort handler always returns "fault". */ -static int +static notrace int do_bad(unsigned long addr, unsigned int fsr, struct pt_regs *regs) { return 1; @@ -423,7 +423,7 @@ static struct fsr_info { { do_bad, SIGBUS, 0, "unknown 31" } }; -void __init +void __init notrace hook_fault_code(int nr, int (*fn)(unsigned long, unsigned int, struct pt_regs *), int sig, const char *name) { @@ -437,7 +437,7 @@ hook_fault_code(int nr, int (*fn)(unsign /* * Dispatch a data abort to the relevant handler. */ -asmlinkage void __exception +asmlinkage void __exception notrace do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs) { const struct fsr_info *inf = fsr_info + (fsr & 15) + ((fsr & (1 << 10)) >> 6); @@ -456,7 +456,7 @@ do_DataAbort(unsigned long addr, unsigne arm_notify_die("", regs, &info, fsr, 0); } -asmlinkage void __exception +asmlinkage void __exception notrace do_PrefetchAbort(unsigned long addr, struct pt_regs *regs) { do_translation_fault(addr, 0, regs); Index: linux/arch/arm/mm/mmu.c =================================================================== --- linux.orig/arch/arm/mm/mmu.c +++ linux/arch/arm/mm/mmu.c @@ -25,7 +25,7 @@ #include "mm.h" -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); extern void _stext, _etext, __data_start, _end; extern pgd_t swapper_pg_dir[PTRS_PER_PGD]; Index: linux/arch/arm/oprofile/op_model_xscale.c =================================================================== --- linux.orig/arch/arm/oprofile/op_model_xscale.c +++ linux/arch/arm/oprofile/op_model_xscale.c @@ -381,8 +381,9 @@ static int xscale_pmu_start(void) { int ret; u32 pmnc = read_pmnc(); + int irq_flags = IRQF_DISABLED | IRQF_NODELAY; - ret = request_irq(XSCALE_PMU_IRQ, xscale_pmu_interrupt, IRQF_DISABLED, + ret = request_irq(XSCALE_PMU_IRQ, xscale_pmu_interrupt, irq_flags, "XScale PMU", (void *)results); if (ret < 0) { Index: linux/arch/i386/Kconfig =================================================================== --- linux.orig/arch/i386/Kconfig +++ linux/arch/i386/Kconfig @@ -18,6 +18,10 @@ config GENERIC_TIME bool default y +config GENERIC_CMOS_UPDATE + bool + default y + config CLOCKSOURCE_WATCHDOG bool default y @@ -31,6 +35,10 @@ config GENERIC_CLOCKEVENTS_BROADCAST default y depends on X86_LOCAL_APIC +config NONIRQ_WAKEUP + bool + default y + config LOCKDEP_SUPPORT bool default y @@ -764,6 +772,14 @@ config BOOT_IOREMAP depends on (((X86_SUMMIT || X86_GENERICARCH) && NUMA) || (X86 && EFI)) default y +# +# function tracing might turn this off: +# +config REGPARM + bool + depends on !MCOUNT + default y + config SECCOMP bool "Enable seccomp to safely compute untrusted bytecode" depends on PROC_FS @@ -1053,6 +1069,8 @@ endif # APM source "arch/i386/kernel/cpu/cpufreq/Kconfig" +source "drivers/cpuidle/Kconfig" + endmenu menu "Bus options (PCI, PCMCIA, EISA, MCA, ISA)" Index: linux/arch/i386/Kconfig.cpu =================================================================== --- linux.orig/arch/i386/Kconfig.cpu +++ linux/arch/i386/Kconfig.cpu @@ -247,12 +247,16 @@ config X86_XADD config RWSEM_GENERIC_SPINLOCK bool - depends on !X86_XADD + depends on !X86_XADD || PREEMPT_RT + default y + +config ASM_SEMAPHORES + bool default y config RWSEM_XCHGADD_ALGORITHM bool - depends on X86_XADD + depends on X86_XADD && !RWSEM_GENERIC_SPINLOCK default y config ARCH_HAS_ILOG2_U32 Index: linux/arch/i386/Kconfig.debug =================================================================== --- linux.orig/arch/i386/Kconfig.debug +++ linux/arch/i386/Kconfig.debug @@ -49,6 +49,7 @@ config DEBUG_PAGEALLOC config DEBUG_RODATA bool "Write protect kernel read-only data structures" depends on DEBUG_KERNEL + default y help Mark the kernel read-only data as write-protected in the pagetables, in order to catch accidental (and incorrect) writes to such const @@ -59,6 +60,7 @@ config DEBUG_RODATA config 4KSTACKS bool "Use 4Kb for kernel stacks instead of 8Kb" depends on DEBUG_KERNEL + default y help If you say Y here the kernel will use a 4Kb stacksize for the kernel stack attached to each process/thread. This facilitates Index: linux/arch/i386/Makefile =================================================================== --- linux.orig/arch/i386/Makefile +++ linux/arch/i386/Makefile @@ -31,7 +31,7 @@ LDFLAGS_vmlinux := --emit-relocs endif CHECKFLAGS += -D__i386__ -CFLAGS += -pipe -msoft-float -mregparm=3 -freg-struct-return +CFLAGS += -pipe -msoft-float # prevent gcc from keeping the stack 16 byte aligned CFLAGS += $(call cc-option,-mpreferred-stack-boundary=2) @@ -39,6 +39,8 @@ CFLAGS += $(call cc-option,-mpreferred-s # CPU-specific tuning. Anything which can be shared with UML should go here. include $(srctree)/arch/i386/Makefile.cpu +cflags-$(CONFIG_REGPARM) += -mregparm=3 -freg-struct-return + # temporary until string.h is fixed cflags-y += -ffreestanding Index: linux/arch/i386/boot/compressed/Makefile =================================================================== --- linux.orig/arch/i386/boot/compressed/Makefile +++ linux/arch/i386/boot/compressed/Makefile @@ -9,6 +9,7 @@ targets := vmlinux vmlinux.bin vmlinux. EXTRA_AFLAGS := -traditional LDFLAGS_vmlinux := -T +CFLAGS := -m32 -D__KERNEL__ -Iinclude -O2 -fno-strict-aliasing CFLAGS_misc.o += -fPIC hostprogs-y := relocs Index: linux/arch/i386/kernel/Makefile =================================================================== --- linux.orig/arch/i386/kernel/Makefile +++ linux/arch/i386/kernel/Makefile @@ -21,6 +21,7 @@ obj-$(CONFIG_APM) += apm.o obj-$(CONFIG_X86_SMP) += smp.o smpboot.o tsc_sync.o obj-$(CONFIG_SMP) += smpcommon.o obj-$(CONFIG_X86_TRAMPOLINE) += trampoline.o +obj-$(CONFIG_MCOUNT) += mcount-wrapper.o obj-$(CONFIG_X86_MPPARSE) += mpparse.o obj-$(CONFIG_X86_LOCAL_APIC) += apic.o nmi.o obj-$(CONFIG_X86_IO_APIC) += io_apic.o Index: linux/arch/i386/kernel/apic.c =================================================================== --- linux.orig/arch/i386/kernel/apic.c +++ linux/arch/i386/kernel/apic.c @@ -263,6 +263,9 @@ static void lapic_timer_setup(enum clock v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR); apic_write_around(APIC_LVTT, v); break; + case CLOCK_EVT_MODE_RESUME: + /* Nothing to do here */ + break; } local_irq_restore(flags); @@ -521,6 +524,9 @@ void __init setup_boot_APIC_clock(void) */ if (nmi_watchdog != NMI_IO_APIC) lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY; + else + printk(KERN_WARNING "APIC timer registered as dummy," + " due to nmi_watchdog=1!\n"); } /* Setup the lapic or request the broadcast */ @@ -573,10 +579,12 @@ static void local_apic_timer_interrupt(v * interrupt as well. Thus we cannot inline the local irq ... ] */ -void fastcall smp_apic_timer_interrupt(struct pt_regs *regs) +void fastcall notrace smp_apic_timer_interrupt(struct pt_regs *regs) { struct pt_regs *old_regs = set_irq_regs(regs); + trace_special(regs->eip, 1, 0); + /* * NOTE! We'd better ACK the irq immediately, * because timer handling can be slow. @@ -1303,6 +1311,7 @@ void smp_error_interrupt(struct pt_regs */ printk (KERN_DEBUG "APIC error on CPU%d: %02lx(%02lx)\n", smp_processor_id(), v , v1); + dump_stack(); irq_exit(); } Index: linux/arch/i386/kernel/apm.c =================================================================== --- linux.orig/arch/i386/kernel/apm.c +++ linux/arch/i386/kernel/apm.c @@ -782,7 +782,7 @@ static int apm_do_idle(void) */ smp_mb(); } - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { idled = 1; ret = apm_bios_call_simple(APM_FUNC_IDLE, 0, 0, &eax); } Index: linux/arch/i386/kernel/cpu/mtrr/generic.c =================================================================== --- linux.orig/arch/i386/kernel/cpu/mtrr/generic.c +++ linux/arch/i386/kernel/cpu/mtrr/generic.c @@ -330,7 +330,7 @@ static unsigned long set_mtrr_state(void static unsigned long cr4 = 0; -static DEFINE_SPINLOCK(set_atomicity_lock); +static DEFINE_RAW_SPINLOCK(set_atomicity_lock); /* * Since we are disabling the cache don't allow any interrupts - they Index: linux/arch/i386/kernel/crash.c =================================================================== --- linux.orig/arch/i386/kernel/crash.c +++ linux/arch/i386/kernel/crash.c @@ -70,14 +70,6 @@ static int crash_nmi_callback(struct not return 1; } -static void smp_send_nmi_allbutself(void) -{ - cpumask_t mask = cpu_online_map; - cpu_clear(safe_smp_processor_id(), mask); - if (!cpus_empty(mask)) - send_IPI_mask(mask, NMI_VECTOR); -} - static struct notifier_block crash_nmi_nb = { .notifier_call = crash_nmi_callback, }; Index: linux/arch/i386/kernel/efi.c =================================================================== --- linux.orig/arch/i386/kernel/efi.c +++ linux/arch/i386/kernel/efi.c @@ -278,7 +278,7 @@ void efi_memmap_walk(efi_freemem_callbac struct range { unsigned long start; unsigned long end; - } prev, curr; + } prev = { } /* shut up gcc */ , curr = { } /* shut up gcc */ ; efi_memory_desc_t *md; unsigned long start, end; void *p; Index: linux/arch/i386/kernel/entry.S =================================================================== --- linux.orig/arch/i386/kernel/entry.S +++ linux/arch/i386/kernel/entry.S @@ -264,14 +264,18 @@ END(ret_from_exception) #ifdef CONFIG_PREEMPT ENTRY(resume_kernel) DISABLE_INTERRUPTS(CLBR_ANY) + cmpl $0, kernel_preemption + jz restore_nocheck cmpl $0,TI_preempt_count(%ebp) # non-zero preempt_count ? jnz restore_nocheck need_resched: movl TI_flags(%ebp), %ecx # need_resched set ? testb $_TIF_NEED_RESCHED, %cl - jz restore_all + jz restore_nocheck testl $IF_MASK,PT_EFLAGS(%esp) # interrupts off (exception path) ? - jz restore_all + jz restore_nocheck + DISABLE_INTERRUPTS(CLBR_ANY) + call preempt_schedule_irq jmp need_resched END(resume_kernel) @@ -329,6 +333,11 @@ sysenter_past_esp: pushl %eax CFI_ADJUST_CFA_OFFSET 4 SAVE_ALL +#ifdef CONFIG_EVENT_TRACE + pushl %edx; pushl %ecx; pushl %ebx; pushl %eax + call sys_call + popl %eax; popl %ebx; popl %ecx; popl %edx +#endif GET_THREAD_INFO(%ebp) /* Note, _TIF_SECCOMP is bit number 8, and so it needs testw and not testb */ @@ -343,6 +352,11 @@ sysenter_past_esp: movl TI_flags(%ebp), %ecx testw $_TIF_ALLWORK_MASK, %cx jne syscall_exit_work +#ifdef CONFIG_EVENT_TRACE + pushl %eax + call sys_ret + popl %eax +#endif /* if something modifies registers it must also disable sysexit */ movl PT_EIP(%esp), %edx movl PT_OLDESP(%esp), %ecx @@ -366,6 +380,11 @@ ENTRY(system_call) pushl %eax # save orig_eax CFI_ADJUST_CFA_OFFSET 4 SAVE_ALL +#ifdef CONFIG_EVENT_TRACE + pushl %edx; pushl %ecx; pushl %ebx; pushl %eax + call sys_call + popl %eax; popl %ebx; popl %ecx; popl %edx +#endif GET_THREAD_INFO(%ebp) # system call tracing in operation / emulation /* Note, _TIF_SECCOMP is bit number 8, and so it needs testw and not testb */ @@ -465,19 +484,19 @@ ENDPROC(system_call) ALIGN RING0_PTREGS_FRAME # can't unwind into user space anyway work_pending: - testb $_TIF_NEED_RESCHED, %cl + testl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED), %ecx jz work_notifysig work_resched: - call schedule - DISABLE_INTERRUPTS(CLBR_ANY) # make sure we don't miss an interrupt + DISABLE_INTERRUPTS(CLBR_ANY) + call __schedule + # make sure we don't miss an interrupt # setting need_resched or sigpending # between sampling and the iret - TRACE_IRQS_OFF movl TI_flags(%ebp), %ecx andl $_TIF_WORK_MASK, %ecx # is there any work to be done other # than syscall tracing? jz restore_all - testb $_TIF_NEED_RESCHED, %cl + testl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED), %ecx jnz work_resched work_notifysig: # deal with pending signals and Index: linux/arch/i386/kernel/head.S =================================================================== --- linux.orig/arch/i386/kernel/head.S +++ linux/arch/i386/kernel/head.S @@ -486,6 +486,7 @@ ignore_int: call printk #endif addl $(5*4),%esp + call dump_stack popl %ds popl %es popl %edx Index: linux/arch/i386/kernel/hpet.c =================================================================== --- linux.orig/arch/i386/kernel/hpet.c +++ linux/arch/i386/kernel/hpet.c @@ -1,11 +1,14 @@ #include #include +#include #include #include #include +#include #include #include +#include #include #include @@ -21,8 +24,34 @@ extern struct clock_event_device *global * HPET address is set in acpi/boot.c, when an ACPI entry exists */ unsigned long hpet_address; + static void __iomem * hpet_virt_address; +#ifdef CONFIG_X86_64 + +#include +#include + +static inline void hpet_set_mapping(void) +{ + set_fixmap_nocache(FIX_HPET_BASE, hpet_address); + __set_fixmap(VSYSCALL_HPET, hpet_address, PAGE_KERNEL_VSYSCALL_NOCACHE); + hpet_virt_address = (void __iomem *)fix_to_virt(FIX_HPET_BASE); + +} + +static inline void __iomem *hpet_get_virt_address(void) +{ + return hpet_virt_address; +} + +static inline void hpet_clear_mapping(void) +{ + hpet_virt_address = NULL; +} + +#else + static inline unsigned long hpet_readl(unsigned long a) { return readl(hpet_virt_address + a); @@ -33,6 +62,23 @@ static inline void hpet_writel(unsigned writel(d, hpet_virt_address + a); } +static inline void hpet_set_mapping(void) +{ + hpet_virt_address = ioremap_nocache(hpet_address, HPET_MMAP_SIZE); +} + +static inline void __iomem *hpet_get_virt_address(void) +{ + return hpet_virt_address; +} + +static inline void hpet_clear_mapping(void) +{ + iounmap(hpet_virt_address); + hpet_virt_address = NULL; +} +#endif + /* * HPET command line enable / disable */ @@ -48,6 +94,13 @@ static int __init hpet_setup(char* str) } __setup("hpet=", hpet_setup); +static int __init disable_hpet(char *str) +{ + boot_hpet_disable = 1; + return 1; +} +__setup("nohpet", disable_hpet); + static inline int is_hpet_capable(void) { return (!boot_hpet_disable && hpet_address); @@ -73,7 +126,7 @@ int is_hpet_enabled(void) #ifdef CONFIG_HPET static void hpet_reserve_platform_timers(unsigned long id) { - struct hpet __iomem *hpet = hpet_virt_address; + struct hpet __iomem *hpet = hpet_get_virt_address(); struct hpet_timer __iomem *timer = &hpet->hpet_timers[2]; unsigned int nrtimers, i; struct hpet_data hd; @@ -82,7 +135,7 @@ static void hpet_reserve_platform_timers memset(&hd, 0, sizeof (hd)); hd.hd_phys_address = hpet_address; - hd.hd_address = hpet_virt_address; + hd.hd_address = hpet; hd.hd_nirqs = nrtimers; hd.hd_flags = HPET_DATA_PLATFORM; hpet_reserve_timer(&hd, 0); @@ -110,9 +163,9 @@ static void hpet_reserve_platform_timers */ static unsigned long hpet_period; -static void hpet_set_mode(enum clock_event_mode mode, +static void hpet_legacy_set_mode(enum clock_event_mode mode, struct clock_event_device *evt); -static int hpet_next_event(unsigned long delta, +static int hpet_legacy_next_event(unsigned long delta, struct clock_event_device *evt); /* @@ -121,10 +174,11 @@ static int hpet_next_event(unsigned long static struct clock_event_device hpet_clockevent = { .name = "hpet", .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, - .set_mode = hpet_set_mode, - .set_next_event = hpet_next_event, + .set_mode = hpet_legacy_set_mode, + .set_next_event = hpet_legacy_next_event, .shift = 32, .irq = 0, + .rating = 50, }; static void hpet_start_counter(void) @@ -139,7 +193,18 @@ static void hpet_start_counter(void) hpet_writel(cfg, HPET_CFG); } -static void hpet_enable_int(void) +static void hpet_resume_device(void) +{ + force_hpet_resume(); +} + +static void hpet_restart_counter(void) +{ + hpet_resume_device(); + hpet_start_counter(); +} + +static void hpet_enable_legacy_int(void) { unsigned long cfg = hpet_readl(HPET_CFG); @@ -148,7 +213,39 @@ static void hpet_enable_int(void) hpet_legacy_int_enabled = 1; } -static void hpet_set_mode(enum clock_event_mode mode, +static void hpet_legacy_clockevent_register(void) +{ + uint64_t hpet_freq; + + /* Start HPET legacy interrupts */ + hpet_enable_legacy_int(); + + /* + * The period is a femto seconds value. We need to calculate the + * scaled math multiplication factor for nanosecond to hpet tick + * conversion. + */ + hpet_freq = 1000000000000000ULL; + do_div(hpet_freq, hpet_period); + hpet_clockevent.mult = div_sc((unsigned long) hpet_freq, + NSEC_PER_SEC, 32); + /* Calculate the min / max delta */ + hpet_clockevent.max_delta_ns = clockevent_delta2ns(0x7FFFFFFF, + &hpet_clockevent); + hpet_clockevent.min_delta_ns = clockevent_delta2ns(0x30, + &hpet_clockevent); + + /* + * Start hpet with the boot cpu mask and make it + * global after the IO_APIC has been initialized. + */ + hpet_clockevent.cpumask = cpumask_of_cpu(smp_processor_id()); + clockevents_register_device(&hpet_clockevent); + global_clock_event = &hpet_clockevent; + printk(KERN_DEBUG "hpet clockevent registered\n"); +} + +static void hpet_legacy_set_mode(enum clock_event_mode mode, struct clock_event_device *evt) { unsigned long cfg, cmp, now; @@ -187,10 +284,14 @@ static void hpet_set_mode(enum clock_eve cfg &= ~HPET_TN_ENABLE; hpet_writel(cfg, HPET_T0_CFG); break; + + case CLOCK_EVT_MODE_RESUME: + hpet_enable_legacy_int(); + break; } } -static int hpet_next_event(unsigned long delta, +static int hpet_legacy_next_event(unsigned long delta, struct clock_event_device *evt) { unsigned long cnt; @@ -205,11 +306,18 @@ static int hpet_next_event(unsigned long /* * Clock source related code */ -static cycle_t read_hpet(void) +static cycle_t notrace read_hpet(void) { return (cycle_t)hpet_readl(HPET_COUNTER); } +#ifdef CONFIG_X86_64 +static cycle_t __vsyscall_fn vread_hpet(void) +{ + return readl((const void __iomem *)fix_to_virt(VSYSCALL_HPET) + 0xf0); +} +#endif + static struct clocksource clocksource_hpet = { .name = "hpet", .rating = 250, @@ -217,21 +325,77 @@ static struct clocksource clocksource_hp .mask = HPET_MASK, .shift = HPET_SHIFT, .flags = CLOCK_SOURCE_IS_CONTINUOUS, + .resume = hpet_restart_counter, +#ifdef CONFIG_X86_64 + .vread = vread_hpet, +#endif }; +static int hpet_clocksource_register(void) +{ + u64 tmp, start, now; + cycle_t t1, t2; + + /* Start the counter */ + hpet_start_counter(); + + /* Verify whether hpet counter works */ + t1 = read_hpet(); + rdtscll(start); + + /* + * We don't know the TSC frequency yet, but waiting for + * 200000 TSC cycles is safe: + * 4 GHz == 50us + * 1 GHz == 200us + */ + do { + rep_nop(); + t2 = read_hpet(); + rdtscll(now); + } while (now - start < 200000UL); + + if (t1 == t2) { + printk(KERN_WARNING + "HPET counter not counting. HPET disabled\n"); + return -ENODEV; + } + + /* Initialize and register HPET clocksource + * + * hpet period is in femto seconds per cycle + * so we need to convert this to ns/cyc units + * aproximated by mult/2^shift + * + * fsec/cyc * 1nsec/1000000fsec = nsec/cyc = mult/2^shift + * fsec/cyc * 1ns/1000000fsec * 2^shift = mult + * fsec/cyc * 2^shift * 1nsec/1000000fsec = mult + * (fsec/cyc << shift)/1000000 = mult + * (hpet_period << shift)/FSEC_PER_NSEC = mult + */ + tmp = (u64)hpet_period << HPET_SHIFT; + do_div(tmp, FSEC_PER_NSEC); + clocksource_hpet.mult = (u32)tmp; + + clocksource_register(&clocksource_hpet); + + return 0; +} + /* * Try to setup the HPET timer */ int __init hpet_enable(void) { unsigned long id; - uint64_t hpet_freq; - u64 tmp; + + if (hpet_get_virt_address()) + return 0; if (!is_hpet_capable()) return 0; - hpet_virt_address = ioremap_nocache(hpet_address, HPET_MMAP_SIZE); + hpet_set_mapping(); /* * Read the period and check for a sane value: @@ -241,21 +405,6 @@ int __init hpet_enable(void) goto out_nohpet; /* - * The period is a femto seconds value. We need to calculate the - * scaled math multiplication factor for nanosecond to hpet tick - * conversion. - */ - hpet_freq = 1000000000000000ULL; - do_div(hpet_freq, hpet_period); - hpet_clockevent.mult = div_sc((unsigned long) hpet_freq, - NSEC_PER_SEC, 32); - /* Calculate the min / max delta */ - hpet_clockevent.max_delta_ns = clockevent_delta2ns(0x7FFFFFFF, - &hpet_clockevent); - hpet_clockevent.min_delta_ns = clockevent_delta2ns(0x30, - &hpet_clockevent); - - /* * Read the HPET ID register to retrieve the IRQ routing * information and the number of channels */ @@ -270,50 +419,44 @@ int __init hpet_enable(void) goto out_nohpet; #endif - /* Start the counter */ - hpet_start_counter(); - - /* Initialize and register HPET clocksource - * - * hpet period is in femto seconds per cycle - * so we need to convert this to ns/cyc units - * aproximated by mult/2^shift - * - * fsec/cyc * 1nsec/1000000fsec = nsec/cyc = mult/2^shift - * fsec/cyc * 1ns/1000000fsec * 2^shift = mult - * fsec/cyc * 2^shift * 1nsec/1000000fsec = mult - * (fsec/cyc << shift)/1000000 = mult - * (hpet_period << shift)/FSEC_PER_NSEC = mult - */ - tmp = (u64)hpet_period << HPET_SHIFT; - do_div(tmp, FSEC_PER_NSEC); - clocksource_hpet.mult = (u32)tmp; - - clocksource_register(&clocksource_hpet); - + if (hpet_clocksource_register()) + goto out_nohpet; if (id & HPET_ID_LEGSUP) { - hpet_enable_int(); - hpet_reserve_platform_timers(id); - /* - * Start hpet with the boot cpu mask and make it - * global after the IO_APIC has been initialized. - */ - hpet_clockevent.cpumask =cpumask_of_cpu(0); - clockevents_register_device(&hpet_clockevent); - global_clock_event = &hpet_clockevent; + hpet_legacy_clockevent_register(); return 1; } return 0; out_nohpet: - iounmap(hpet_virt_address); - hpet_virt_address = NULL; + hpet_clear_mapping(); boot_hpet_disable = 1; return 0; } +static int __init hpet_late_init(void) +{ + if (boot_hpet_disable) + return -ENODEV; + + if (!hpet_address) { + if (!force_hpet_address) + return -ENODEV; + + hpet_address = force_hpet_address; + hpet_enable(); + if (!hpet_get_virt_address()) + return -ENODEV; + } + + hpet_reserve_platform_timers(hpet_readl(HPET_ID)); + + return 0; +} +fs_initcall(hpet_late_init); + + #ifdef CONFIG_HPET_EMULATE_RTC /* HPET in LegacyReplacement Mode eats up RTC interrupt line. When, HPET @@ -524,68 +667,3 @@ irqreturn_t hpet_rtc_interrupt(int irq, return IRQ_HANDLED; } #endif - - -/* - * Suspend/resume part - */ - -#ifdef CONFIG_PM - -static int hpet_suspend(struct sys_device *sys_device, pm_message_t state) -{ - unsigned long cfg = hpet_readl(HPET_CFG); - - cfg &= ~(HPET_CFG_ENABLE|HPET_CFG_LEGACY); - hpet_writel(cfg, HPET_CFG); - - return 0; -} - -static int hpet_resume(struct sys_device *sys_device) -{ - unsigned int id; - - hpet_start_counter(); - - id = hpet_readl(HPET_ID); - - if (id & HPET_ID_LEGSUP) - hpet_enable_int(); - - return 0; -} - -static struct sysdev_class hpet_class = { - set_kset_name("hpet"), - .suspend = hpet_suspend, - .resume = hpet_resume, -}; - -static struct sys_device hpet_device = { - .id = 0, - .cls = &hpet_class, -}; - - -static __init int hpet_register_sysfs(void) -{ - int err; - - if (!is_hpet_capable()) - return 0; - - err = sysdev_class_register(&hpet_class); - - if (!err) { - err = sysdev_register(&hpet_device); - if (err) - sysdev_class_unregister(&hpet_class); - } - - return err; -} - -device_initcall(hpet_register_sysfs); - -#endif Index: linux/arch/i386/kernel/i386_ksyms.c =================================================================== --- linux.orig/arch/i386/kernel/i386_ksyms.c +++ linux/arch/i386/kernel/i386_ksyms.c @@ -2,10 +2,12 @@ #include #include -EXPORT_SYMBOL(__down_failed); -EXPORT_SYMBOL(__down_failed_interruptible); -EXPORT_SYMBOL(__down_failed_trylock); -EXPORT_SYMBOL(__up_wakeup); +#ifdef CONFIG_ASM_SEMAPHORES +EXPORT_SYMBOL(__compat_down_failed); +EXPORT_SYMBOL(__compat_down_failed_interruptible); +EXPORT_SYMBOL(__compat_down_failed_trylock); +EXPORT_SYMBOL(__compat_up_wakeup); +#endif /* Networking helper routines. */ EXPORT_SYMBOL(csum_partial_copy_generic); @@ -20,7 +22,7 @@ EXPORT_SYMBOL(__put_user_8); EXPORT_SYMBOL(strstr); -#ifdef CONFIG_SMP +#if defined(CONFIG_SMP) && defined(CONFIG_ASM_SEMAPHORES) extern void FASTCALL( __write_lock_failed(rwlock_t *rw)); extern void FASTCALL( __read_lock_failed(rwlock_t *rw)); EXPORT_SYMBOL(__write_lock_failed); Index: linux/arch/i386/kernel/i8253.c =================================================================== --- linux.orig/arch/i386/kernel/i8253.c +++ linux/arch/i386/kernel/i8253.c @@ -3,20 +3,18 @@ * */ #include -#include +#include +#include #include -#include #include -#include +#include #include #include #include #include -#include "io_ports.h" - -DEFINE_SPINLOCK(i8253_lock); +DEFINE_RAW_SPINLOCK(i8253_lock); EXPORT_SYMBOL(i8253_lock); /* @@ -41,26 +39,27 @@ static void init_pit_timer(enum clock_ev case CLOCK_EVT_MODE_PERIODIC: /* binary, mode 2, LSB/MSB, ch 0 */ outb_p(0x34, PIT_MODE); - udelay(10); outb_p(LATCH & 0xff , PIT_CH0); /* LSB */ - udelay(10); outb(LATCH >> 8 , PIT_CH0); /* MSB */ break; - /* - * Avoid unnecessary state transitions, as it confuses - * Geode / Cyrix based boxen. - */ case CLOCK_EVT_MODE_SHUTDOWN: - if (evt->mode == CLOCK_EVT_MODE_UNUSED) - break; case CLOCK_EVT_MODE_UNUSED: - if (evt->mode == CLOCK_EVT_MODE_SHUTDOWN) - break; + if (evt->mode == CLOCK_EVT_MODE_PERIODIC || + evt->mode == CLOCK_EVT_MODE_ONESHOT) { + outb_p(0x30, PIT_MODE); + outb_p(0, PIT_CH0); + outb_p(0, PIT_CH0); + } + break; + case CLOCK_EVT_MODE_ONESHOT: /* One shot setup */ outb_p(0x38, PIT_MODE); - udelay(10); + break; + + case CLOCK_EVT_MODE_RESUME: + /* Nothing to do here */ break; } spin_unlock_irqrestore(&i8253_lock, flags); @@ -120,6 +119,7 @@ void __init setup_pit_timer(void) global_clock_event = &pit_clockevent; } +#ifndef CONFIG_X86_64 /* * Since the PIT overflows every tick, its not very useful * to just read by itself. So use jiffies to emulate a free @@ -204,3 +204,5 @@ static int __init init_pit_clocksource(v return clocksource_register(&clocksource_pit); } arch_initcall(init_pit_clocksource); + +#endif Index: linux/arch/i386/kernel/i8259.c =================================================================== --- linux.orig/arch/i386/kernel/i8259.c +++ linux/arch/i386/kernel/i8259.c @@ -34,7 +34,7 @@ */ static int i8259A_auto_eoi; -DEFINE_SPINLOCK(i8259A_lock); +DEFINE_RAW_SPINLOCK(i8259A_lock); static void mask_and_ack_8259A(unsigned int); static struct irq_chip i8259A_chip = { @@ -170,6 +170,8 @@ static void mask_and_ack_8259A(unsigned */ if (cached_irq_mask & irqmask) goto spurious_8259A_irq; + if (irq & 8) + outb(0x60+(irq&7),PIC_SLAVE_CMD); /* 'Specific EOI' to slave */ cached_irq_mask |= irqmask; handle_real_irq: @@ -297,10 +299,10 @@ void init_8259A(int auto_eoi) outb_p(0x11, PIC_MASTER_CMD); /* ICW1: select 8259A-1 init */ outb_p(0x20 + 0, PIC_MASTER_IMR); /* ICW2: 8259A-1 IR0-7 mapped to 0x20-0x27 */ outb_p(1U << PIC_CASCADE_IR, PIC_MASTER_IMR); /* 8259A-1 (the master) has a slave on IR2 */ - if (auto_eoi) /* master does Auto EOI */ - outb_p(MASTER_ICW4_DEFAULT | PIC_ICW4_AEOI, PIC_MASTER_IMR); - else /* master expects normal EOI */ + if (!auto_eoi) /* master expects normal EOI */ outb_p(MASTER_ICW4_DEFAULT, PIC_MASTER_IMR); + else /* master does Auto EOI */ + outb_p(MASTER_ICW4_DEFAULT | PIC_ICW4_AEOI, PIC_MASTER_IMR); outb_p(0x11, PIC_SLAVE_CMD); /* ICW1: select 8259A-2 init */ outb_p(0x20 + 8, PIC_SLAVE_IMR); /* ICW2: 8259A-2 IR0-7 mapped to 0x28-0x2f */ @@ -350,7 +352,7 @@ static irqreturn_t math_error_irq(int cp * New motherboards sometimes make IRQ 13 be a PCI interrupt, * so allow interrupt sharing. */ -static struct irqaction fpu_irq = { math_error_irq, 0, CPU_MASK_NONE, "fpu", NULL, NULL }; +static struct irqaction fpu_irq = { math_error_irq, IRQF_NODELAY, CPU_MASK_NONE, "fpu", NULL, NULL }; void __init init_ISA_irqs (void) { Index: linux/arch/i386/kernel/io_apic.c =================================================================== --- linux.orig/arch/i386/kernel/io_apic.c +++ linux/arch/i386/kernel/io_apic.c @@ -56,8 +56,8 @@ atomic_t irq_mis_count; /* Where if anywhere is the i8259 connect in external int mode */ static struct { int pin, apic; } ioapic_i8259 = { -1, -1 }; -static DEFINE_SPINLOCK(ioapic_lock); -static DEFINE_SPINLOCK(vector_lock); +static DEFINE_RAW_SPINLOCK(ioapic_lock); +static DEFINE_RAW_SPINLOCK(vector_lock); int timer_over_8254 __initdata = 1; @@ -261,14 +261,14 @@ static void __unmask_IO_APIC_irq (unsign __modify_IO_APIC_irq(irq, 0, 0x00010000); } -/* mask = 1, trigger = 0 */ -static void __mask_and_edge_IO_APIC_irq (unsigned int irq) +/* trigger = 0 (edge mode) */ +static void __pcix_mask_IO_APIC_irq (unsigned int irq) { - __modify_IO_APIC_irq(irq, 0x00010000, 0x00008000); + __modify_IO_APIC_irq(irq, 0, 0x00008000); } -/* mask = 0, trigger = 1 */ -static void __unmask_and_level_IO_APIC_irq (unsigned int irq) +/* mask = 0, trigger = 1 (level mode) */ +static void __pcix_unmask_IO_APIC_irq (unsigned int irq) { __modify_IO_APIC_irq(irq, 0x00008000, 0x00010000); } @@ -291,6 +291,24 @@ static void unmask_IO_APIC_irq (unsigned spin_unlock_irqrestore(&ioapic_lock, flags); } +static void pcix_mask_IO_APIC_irq (unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&ioapic_lock, flags); + __pcix_mask_IO_APIC_irq(irq); + spin_unlock_irqrestore(&ioapic_lock, flags); +} + +static void pcix_unmask_IO_APIC_irq (unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&ioapic_lock, flags); + __pcix_unmask_IO_APIC_irq(irq); + spin_unlock_irqrestore(&ioapic_lock, flags); +} + static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin) { struct IO_APIC_route_entry entry; @@ -1266,21 +1284,27 @@ static int assign_irq_vector(int irq) return vector; } + static struct irq_chip ioapic_chip; +static struct irq_chip pcix_ioapic_chip; #define IOAPIC_AUTO -1 #define IOAPIC_EDGE 0 #define IOAPIC_LEVEL 1 -static void ioapic_register_intr(int irq, int vector, unsigned long trigger) +static void ioapic_register_intr(int irq, int vector, unsigned long trigger, + int pcix) { + struct irq_chip *chip = pcix ? &pcix_ioapic_chip : &ioapic_chip; + if ((trigger == IOAPIC_AUTO && IO_APIC_irq_trigger(irq)) || trigger == IOAPIC_LEVEL) - set_irq_chip_and_handler_name(irq, &ioapic_chip, - handle_fasteoi_irq, "fasteoi"); + set_irq_chip_and_handler_name(irq, chip, handle_fasteoi_irq, + pcix ? "pcix-fasteoi" : "fasteoi"); else - set_irq_chip_and_handler_name(irq, &ioapic_chip, - handle_edge_irq, "edge"); + set_irq_chip_and_handler_name(irq, chip, handle_edge_irq, + pcix ? "pcix-edge" : "edge"); + set_intr_gate(vector, interrupt[irq]); } @@ -1344,7 +1368,8 @@ static void __init setup_IO_APIC_irqs(vo if (IO_APIC_IRQ(irq)) { vector = assign_irq_vector(irq); entry.vector = vector; - ioapic_register_intr(irq, vector, IOAPIC_AUTO); + ioapic_register_intr(irq, vector, IOAPIC_AUTO, + apic > 0); if (!apic && (irq < 16)) disable_8259A_irq(irq); @@ -1515,7 +1540,7 @@ void __init print_IO_APIC(void) return; } -#if 0 +#if 1 static void print_APIC_bitfield (int base) { @@ -1919,7 +1944,7 @@ int __init timer_irq_works(void) * might have cached one ExtINT interrupt. Finally, at * least one tick may be lost due to delays. */ - if (jiffies - t1 > 4) + if (jiffies - t1 > 4 && jiffies - t1 < 16) return 1; return 0; @@ -2008,8 +2033,10 @@ static void ack_ioapic_quirk_irq(unsigne if (!(v & (1 << (i & 0x1f)))) { atomic_inc(&irq_mis_count); spin_lock(&ioapic_lock); - __mask_and_edge_IO_APIC_irq(irq); - __unmask_and_level_IO_APIC_irq(irq); + /* mask = 1, trigger = 0 */ + __modify_IO_APIC_irq(irq, 0x00010000, 0x00008000); + /* mask = 0, trigger = 1 */ + __modify_IO_APIC_irq(irq, 0x00008000, 0x00010000); spin_unlock(&ioapic_lock); } } @@ -2034,6 +2061,18 @@ static struct irq_chip ioapic_chip __rea .retrigger = ioapic_retrigger_irq, }; +static struct irq_chip pcix_ioapic_chip __read_mostly = { + .name = "IO-APIC", + .startup = startup_ioapic_irq, + .mask = pcix_mask_IO_APIC_irq, + .unmask = pcix_unmask_IO_APIC_irq, + .ack = ack_ioapic_irq, + .eoi = ack_ioapic_irq, +#ifdef CONFIG_SMP + .set_affinity = set_ioapic_affinity_irq, +#endif + .retrigger = ioapic_retrigger_irq, +}; static inline void init_IO_APIC_traps(void) { @@ -2834,7 +2873,7 @@ int io_apic_set_pci_routing (int ioapic, mp_ioapics[ioapic].mpc_apicid, pin, entry.vector, irq, edge_level, active_high_low); - ioapic_register_intr(irq, entry.vector, edge_level); + ioapic_register_intr(irq, entry.vector, edge_level, ioapic > 0); if (!ioapic && (irq < 16)) disable_8259A_irq(irq); Index: linux/arch/i386/kernel/irq.c =================================================================== --- linux.orig/arch/i386/kernel/irq.c +++ linux/arch/i386/kernel/irq.c @@ -68,7 +68,7 @@ static union irq_ctx *softirq_ctx[NR_CPU * SMP cross-CPU interrupts have their own specific * handlers). */ -fastcall unsigned int do_IRQ(struct pt_regs *regs) +fastcall notrace unsigned int do_IRQ(struct pt_regs *regs) { struct pt_regs *old_regs; /* high bit used in ret_from_ code */ @@ -79,6 +79,10 @@ fastcall unsigned int do_IRQ(struct pt_r u32 *isp; #endif +#ifdef CONFIG_X86_LOCAL_APIC + irq_show_regs_callback(smp_processor_id(), regs); +#endif + if (unlikely((unsigned)irq >= NR_IRQS)) { printk(KERN_EMERG "%s: cannot handle IRQ %d\n", __FUNCTION__, irq); @@ -87,6 +91,11 @@ fastcall unsigned int do_IRQ(struct pt_r old_regs = set_irq_regs(regs); irq_enter(); +#ifdef CONFIG_EVENT_TRACE + if (irq == trace_user_trigger_irq) + user_trace_start(); +#endif + trace_special(regs->eip, irq, 0); #ifdef CONFIG_DEBUG_STACKOVERFLOW /* Debugging check for stack overflow: is there less than 1KB free? */ { @@ -95,7 +104,7 @@ fastcall unsigned int do_IRQ(struct pt_r __asm__ __volatile__("andl %%esp,%0" : "=r" (esp) : "0" (THREAD_SIZE - 1)); if (unlikely(esp < (sizeof(struct thread_info) + STACK_WARN))) { - printk("do_IRQ: stack overflow: %ld\n", + printk("BUG: do_IRQ: stack overflow: %ld\n", esp - sizeof(struct thread_info)); dump_stack(); } Index: linux/arch/i386/kernel/kprobes.c =================================================================== --- linux.orig/arch/i386/kernel/kprobes.c +++ linux/arch/i386/kernel/kprobes.c @@ -329,7 +329,7 @@ ss_probe: /* Boost up -- we can execute copied instructions directly */ reset_current_kprobe(); regs->eip = (unsigned long)p->ainsn.insn; - preempt_enable_no_resched(); + preempt_enable(); return 1; } #endif @@ -338,7 +338,7 @@ ss_probe: return 1; no_kprobe: - preempt_enable_no_resched(); + preempt_enable(); return ret; } @@ -569,7 +569,7 @@ static int __kprobes post_kprobe_handler } reset_current_kprobe(); out: - preempt_enable_no_resched(); + preempt_enable(); /* * if somebody else is singlestepping across a probe point, eflags @@ -603,7 +603,7 @@ static int __kprobes kprobe_fault_handle restore_previous_kprobe(kcb); else reset_current_kprobe(); - preempt_enable_no_resched(); + preempt_enable(); break; case KPROBE_HIT_ACTIVE: case KPROBE_HIT_SSDONE: @@ -665,12 +665,11 @@ int __kprobes kprobe_exceptions_notify(s break; case DIE_GPF: case DIE_PAGE_FAULT: + // TODO: do this better on PREEMPT_RT /* kprobe_running() needs smp_processor_id() */ - preempt_disable(); - if (kprobe_running() && + if (per_cpu(current_kprobe, raw_smp_processor_id()) && kprobe_fault_handler(args->regs, args->trapnr)) ret = NOTIFY_STOP; - preempt_enable(); break; default: break; @@ -737,7 +736,7 @@ int __kprobes longjmp_break_handler(stru *regs = kcb->jprobe_saved_regs; memcpy((kprobe_opcode_t *) stack_addr, kcb->jprobes_stack, MIN_STACK_SIZE(stack_addr)); - preempt_enable_no_resched(); + preempt_enable(); return 1; } return 0; Index: linux/arch/i386/kernel/mcount-wrapper.S =================================================================== --- /dev/null +++ linux/arch/i386/kernel/mcount-wrapper.S @@ -0,0 +1,27 @@ +/* + * linux/arch/i386/mcount-wrapper.S + * + * Copyright (C) 2004 Ingo Molnar + */ + +.globl mcount +mcount: + + cmpl $0, mcount_enabled + jz out + + push %ebp + mov %esp, %ebp + pushl %eax + pushl %ecx + pushl %edx + + call __mcount + + popl %edx + popl %ecx + popl %eax + popl %ebp +out: + ret + Index: linux/arch/i386/kernel/microcode.c =================================================================== --- linux.orig/arch/i386/kernel/microcode.c +++ linux/arch/i386/kernel/microcode.c @@ -116,7 +116,7 @@ MODULE_LICENSE("GPL"); #define exttable_size(et) ((et)->count * EXT_SIGNATURE_SIZE + EXT_HEADER_SIZE) /* serialize access to the physical write to MSR 0x79 */ -static DEFINE_SPINLOCK(microcode_update_lock); +static DEFINE_RAW_SPINLOCK(microcode_update_lock); /* no concurrent ->write()s are allowed on /dev/cpu/microcode */ static DEFINE_MUTEX(microcode_mutex); Index: linux/arch/i386/kernel/nmi.c =================================================================== --- linux.orig/arch/i386/kernel/nmi.c +++ linux/arch/i386/kernel/nmi.c @@ -28,6 +28,8 @@ #include #include +#include + #include "mach_traps.h" int unknown_nmi_panic; @@ -44,7 +46,7 @@ static cpumask_t backtrace_mask = CPU_MA atomic_t nmi_active = ATOMIC_INIT(0); /* oprofile uses this */ unsigned int nmi_watchdog = NMI_DEFAULT; -static unsigned int nmi_hz = HZ; +static unsigned int nmi_hz = 1000; static DEFINE_PER_CPU(short, wd_enabled); @@ -60,7 +62,12 @@ static int endflag __initdata = 0; */ static __init void nmi_cpu_busy(void *data) { + /* + * avoid a warning, on PREEMPT_RT this wont run in hardirq context: + */ +#ifndef CONFIG_PREEMPT_RT local_irq_enable_in_hardirq(); +#endif /* Intentionally don't use cpu_relax here. This is to make sure that the performance counter really ticks, even if there is a simulator or similar that catches the @@ -95,7 +102,7 @@ static int __init check_nmi_watchdog(voi for_each_possible_cpu(cpu) prev_nmi_count[cpu] = per_cpu(irq_stat, cpu).__nmi_count; local_irq_enable(); - mdelay((20*1000)/nmi_hz); // wait 20 ticks + mdelay((100*1000)/nmi_hz); /* wait 100 ticks */ for_each_possible_cpu(cpu) { #ifdef CONFIG_SMP @@ -317,9 +324,48 @@ EXPORT_SYMBOL(touch_nmi_watchdog); extern void die_nmi(struct pt_regs *, const char *msg); -__kprobes int nmi_watchdog_tick(struct pt_regs * regs, unsigned reason) +int nmi_show_regs[NR_CPUS]; + +void nmi_show_all_regs(void) +{ + int i; + + if (system_state == SYSTEM_BOOTING) + return; + + printk(KERN_WARNING "nmi_show_all_regs(): start on CPU#%d.\n", + raw_smp_processor_id()); + dump_stack(); + + for_each_online_cpu(i) + nmi_show_regs[i] = 1; + + smp_send_nmi_allbutself(); + + for_each_online_cpu(i) { + while (nmi_show_regs[i] == 1) + barrier(); + } +} + +static DEFINE_RAW_SPINLOCK(nmi_print_lock); + +notrace void irq_show_regs_callback(int cpu, struct pt_regs *regs) { + if (!nmi_show_regs[cpu]) + return; + + nmi_show_regs[cpu] = 0; + spin_lock(&nmi_print_lock); + printk(KERN_WARNING "NMI show regs on CPU#%d:\n", cpu); + printk(KERN_WARNING "apic_timer_irqs: %d\n", + per_cpu(irq_stat, cpu).apic_timer_irqs); + show_regs(regs); + spin_unlock(&nmi_print_lock); +} +notrace __kprobes int nmi_watchdog_tick(struct pt_regs *regs, unsigned reason) +{ /* * Since current_thread_info()-> is always on the stack, and we * always switch the stack NMI-atomically, it's safe to use @@ -330,6 +376,8 @@ __kprobes int nmi_watchdog_tick(struct p int cpu = smp_processor_id(); int rc=0; + __profile_tick(CPU_PROFILING, regs); + /* check for other users first */ if (notify_die(DIE_NMI, "nmi", regs, reason, 2, SIGINT) == NOTIFY_STOP) { @@ -342,7 +390,7 @@ __kprobes int nmi_watchdog_tick(struct p spin_lock(&lock); printk("NMI backtrace for cpu %d\n", cpu); - dump_stack(); + show_regs(regs); spin_unlock(&lock); cpu_clear(cpu, backtrace_mask); } @@ -353,6 +401,9 @@ __kprobes int nmi_watchdog_tick(struct p */ sum = per_cpu(irq_stat, cpu).apic_timer_irqs + kstat_irqs(0); + irq_show_regs_callback(cpu, regs); + + /* if the apic timer isn't firing, this cpu isn't doing much */ /* if the none of the timers isn't firing, this cpu isn't doing much */ if (!touched && last_irq_sums[cpu] == sum) { /* @@ -360,11 +411,29 @@ __kprobes int nmi_watchdog_tick(struct p * wait a few IRQs (5 seconds) before doing the oops ... */ alert_counter[cpu]++; - if (alert_counter[cpu] == 5*nmi_hz) - /* - * die_nmi will return ONLY if NOTIFY_STOP happens.. - */ - die_nmi(regs, "BUG: NMI Watchdog detected LOCKUP"); + if (alert_counter[cpu] && !(alert_counter[cpu] % (5*nmi_hz))) { + int i; + + spin_lock(&nmi_print_lock); + printk(KERN_WARNING "NMI watchdog detected lockup on " + "CPU#%d (%d/%d)\n", cpu, alert_counter[cpu], + 5*nmi_hz); + show_regs(regs); + spin_unlock(&nmi_print_lock); + + for_each_online_cpu(i) { + if (i == cpu) + continue; + nmi_show_regs[i] = 1; + while (nmi_show_regs[i] == 1) + cpu_relax(); + } + printk(KERN_WARNING "NMI watchdog running again ...\n"); + for_each_online_cpu(i) + alert_counter[i] = 0; + + } + } else { last_irq_sums[cpu] = sum; alert_counter[cpu] = 0; @@ -462,5 +531,15 @@ void __trigger_all_cpu_backtrace(void) } } +void smp_send_nmi_allbutself(void) +{ +#ifdef CONFIG_SMP + cpumask_t mask = cpu_online_map; + cpu_clear(safe_smp_processor_id(), mask); + if (!cpus_empty(mask)) + send_IPI_mask(mask, NMI_VECTOR); +#endif +} + EXPORT_SYMBOL(nmi_active); EXPORT_SYMBOL(nmi_watchdog); Index: linux/arch/i386/kernel/process.c =================================================================== --- linux.orig/arch/i386/kernel/process.c +++ linux/arch/i386/kernel/process.c @@ -115,7 +115,7 @@ void default_idle(void) smp_mb(); local_irq_disable(); - if (!need_resched()) + if (!need_resched() && !need_resched_delayed()) safe_halt(); /* enables interrupts racelessly */ else local_irq_enable(); @@ -136,7 +136,9 @@ EXPORT_SYMBOL(default_idle); */ static void poll_idle (void) { - cpu_relax(); + do { + cpu_relax(); + } while (!need_resched() && !need_resched_delayed()); } #ifdef CONFIG_HOTPLUG_CPU @@ -179,13 +181,14 @@ void cpu_idle(void) /* endless idle loop with no priority at all */ while (1) { - tick_nohz_stop_sched_tick(); - while (!need_resched()) { + while (!need_resched() && !need_resched_delayed()) { void (*idle)(void); if (__get_cpu_var(cpu_idle_state)) __get_cpu_var(cpu_idle_state) = 0; + tick_nohz_stop_sched_tick(); + check_pgt_cache(); rmb(); idle = pm_idle; @@ -199,10 +202,14 @@ void cpu_idle(void) __get_cpu_var(irq_stat).idle_timestamp = jiffies; idle(); } + local_irq_disable(); + trace_preempt_exit_idle(); tick_nohz_restart_sched_tick(); - preempt_enable_no_resched(); - schedule(); + __preempt_enable_no_resched(); + __schedule(); preempt_disable(); + trace_preempt_enter_idle(); + local_irq_enable(); } } @@ -248,10 +255,10 @@ EXPORT_SYMBOL_GPL(cpu_idle_wait); */ void mwait_idle_with_hints(unsigned long eax, unsigned long ecx) { - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { __monitor((void *)¤t_thread_info()->flags, 0, 0); smp_mb(); - if (!need_resched()) + if (!need_resched() && !need_resched_delayed()) __mwait(eax, ecx); } } @@ -368,15 +375,23 @@ void exit_thread(void) if (unlikely(test_thread_flag(TIF_IO_BITMAP))) { struct task_struct *tsk = current; struct thread_struct *t = &tsk->thread; - int cpu = get_cpu(); - struct tss_struct *tss = &per_cpu(init_tss, cpu); + void *io_bitmap_ptr = t->io_bitmap_ptr; + int cpu; + struct tss_struct *tss; - kfree(t->io_bitmap_ptr); + /* + * On PREEMPT_RT we must not call kfree() with + * preemption disabled, so we first zap the pointer: + */ t->io_bitmap_ptr = NULL; + kfree(io_bitmap_ptr); + clear_thread_flag(TIF_IO_BITMAP); /* * Careful, clear this in the TSS too: */ + cpu = get_cpu(); + tss = &per_cpu(init_tss, cpu); memset(tss->io_bitmap, 0xff, tss->io_bitmap_max); t->io_bitmap_max = 0; tss->io_bitmap_owner = NULL; Index: linux/arch/i386/kernel/quirks.c =================================================================== --- linux.orig/arch/i386/kernel/quirks.c +++ linux/arch/i386/kernel/quirks.c @@ -4,6 +4,8 @@ #include #include +#include + #if defined(CONFIG_X86_IO_APIC) && defined(CONFIG_SMP) && defined(CONFIG_PCI) static void __devinit quirk_intel_irqbalance(struct pci_dev *dev) @@ -47,3 +49,275 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_IN DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_intel_irqbalance); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_intel_irqbalance); #endif + +#if defined(CONFIG_HPET_TIMER) +unsigned long force_hpet_address; + +static enum { + NONE_FORCE_HPET_RESUME, + OLD_ICH_FORCE_HPET_RESUME, + ICH_FORCE_HPET_RESUME, + VT8237_FORCE_HPET_RESUME +} force_hpet_resume_type; + +static void __iomem *rcba_base; + +static void ich_force_hpet_resume(void) +{ + u32 val; + + if (!force_hpet_address) + return; + + if (rcba_base == NULL) + BUG(); + + /* read the Function Disable register, dword mode only */ + val = readl(rcba_base + 0x3404); + if (!(val & 0x80)) { + /* HPET disabled in HPTC. Trying to enable */ + writel(val | 0x80, rcba_base + 0x3404); + } + + val = readl(rcba_base + 0x3404); + if (!(val & 0x80)) + BUG(); + else + printk(KERN_DEBUG "Force enabled HPET at resume\n"); + + return; +} + +static void ich_force_enable_hpet(struct pci_dev *dev) +{ + u32 val, rcba; + int err = 0; + + if (hpet_address || force_hpet_address) + return; + + pci_read_config_dword(dev, 0xF0, &rcba); + rcba &= 0xFFFFC000; + if (rcba == 0) { + printk(KERN_DEBUG "RCBA disabled. Cannot force enable HPET\n"); + return; + } + + /* use bits 31:14, 16 kB aligned */ + rcba_base = ioremap_nocache(rcba, 0x4000); + if (rcba_base == NULL) { + printk(KERN_DEBUG "ioremap failed. Cannot force enable HPET\n"); + return; + } + + /* read the Function Disable register, dword mode only */ + val = readl(rcba_base + 0x3404); + + if (val & 0x80) { + /* HPET is enabled in HPTC. Just not reported by BIOS */ + val = val & 0x3; + force_hpet_address = 0xFED00000 | (val << 12); + printk(KERN_DEBUG "Force enabled HPET at base address 0x%lx\n", + force_hpet_address); + iounmap(rcba_base); + return; + } + + /* HPET disabled in HPTC. Trying to enable */ + writel(val | 0x80, rcba_base + 0x3404); + + val = readl(rcba_base + 0x3404); + if (!(val & 0x80)) { + err = 1; + } else { + val = val & 0x3; + force_hpet_address = 0xFED00000 | (val << 12); + } + + if (err) { + force_hpet_address = 0; + iounmap(rcba_base); + printk(KERN_DEBUG "Failed to force enable HPET\n"); + } else { + force_hpet_resume_type = ICH_FORCE_HPET_RESUME; + printk(KERN_DEBUG "Force enabled HPET at base address 0x%lx\n", + force_hpet_address); + } +} + +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, + ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, + ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, + ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, + ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, + ich_force_enable_hpet); + + +static struct pci_dev *cached_dev; + +static void old_ich_force_hpet_resume(void) +{ + u32 val, gen_cntl; + + if (!force_hpet_address || !cached_dev) + return; + + pci_read_config_dword(cached_dev, 0xD0, &gen_cntl); + gen_cntl &= (~(0x7 << 15)); + gen_cntl |= (0x4 << 15); + + pci_write_config_dword(cached_dev, 0xD0, gen_cntl); + pci_read_config_dword(cached_dev, 0xD0, &gen_cntl); + val = gen_cntl >> 15; + val &= 0x7; + if (val == 0x4) + printk(KERN_DEBUG "Force enabled HPET at resume\n"); + else + BUG(); +} + +static void old_ich_force_enable_hpet(struct pci_dev *dev) +{ + u32 val, gen_cntl; + + if (hpet_address || force_hpet_address) + return; + + pci_read_config_dword(dev, 0xD0, &gen_cntl); + /* + * Bit 17 is HPET enable bit. + * Bit 16:15 control the HPET base address. + */ + val = gen_cntl >> 15; + val &= 0x7; + if (val & 0x4) { + val &= 0x3; + force_hpet_address = 0xFED00000 | (val << 12); + printk(KERN_DEBUG "HPET at base address 0x%lx\n", + force_hpet_address); + return; + } + + /* + * HPET is disabled. Trying enabling at FED00000 and check + * whether it sticks + */ + gen_cntl &= (~(0x7 << 15)); + gen_cntl |= (0x4 << 15); + pci_write_config_dword(dev, 0xD0, gen_cntl); + + pci_read_config_dword(dev, 0xD0, &gen_cntl); + + val = gen_cntl >> 15; + val &= 0x7; + if (val & 0x4) { + /* HPET is enabled in HPTC. Just not reported by BIOS */ + val &= 0x3; + force_hpet_address = 0xFED00000 | (val << 12); + printk(KERN_DEBUG "Force enabled HPET at base address 0x%lx\n", + force_hpet_address); + cached_dev = dev; + force_hpet_resume_type = OLD_ICH_FORCE_HPET_RESUME; + return; + } + + printk(KERN_DEBUG "Failed to force enable HPET\n"); +} + +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, + old_ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, + old_ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, + old_ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, + old_ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, + old_ich_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_12, + old_ich_force_enable_hpet); + + +static void vt8237_force_hpet_resume(void) +{ + u32 val; + + if (!force_hpet_address || !cached_dev) + return; + + val = 0xfed00000 | 0x80; + pci_write_config_dword(cached_dev, 0x68, val); + + pci_read_config_dword(cached_dev, 0x68, &val); + if (val & 0x80) + printk(KERN_DEBUG "Force enabled HPET at resume\n"); + else + BUG(); +} + +static void vt8237_force_enable_hpet(struct pci_dev *dev) +{ + u32 val; + + if (hpet_address || force_hpet_address) + return; + + pci_read_config_dword(dev, 0x68, &val); + /* + * Bit 7 is HPET enable bit. + * Bit 31:10 is HPET base address (contrary to what datasheet claims) + */ + if (val & 0x80) { + force_hpet_address = (val & ~0x3ff); + printk(KERN_DEBUG "HPET at base address 0x%lx\n", + force_hpet_address); + return; + } + + /* + * HPET is disabled. Trying enabling at FED00000 and check + * whether it sticks + */ + val = 0xfed00000 | 0x80; + pci_write_config_dword(dev, 0x68, val); + + pci_read_config_dword(dev, 0x68, &val); + if (val & 0x80) { + force_hpet_address = (val & ~0x3ff); + printk(KERN_DEBUG "Force enabled HPET at base address 0x%lx\n", + force_hpet_address); + cached_dev = dev; + force_hpet_resume_type = VT8237_FORCE_HPET_RESUME; + return; + } + + printk(KERN_DEBUG "Failed to force enable HPET\n"); +} + +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, + vt8237_force_enable_hpet); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, + vt8237_force_enable_hpet); + +void force_hpet_resume(void) +{ + switch (force_hpet_resume_type) { + case ICH_FORCE_HPET_RESUME: + return ich_force_hpet_resume(); + + case OLD_ICH_FORCE_HPET_RESUME: + return old_ich_force_hpet_resume(); + + case VT8237_FORCE_HPET_RESUME: + return vt8237_force_hpet_resume(); + + default: + break; + } +} + +#endif Index: linux/arch/i386/kernel/signal.c =================================================================== --- linux.orig/arch/i386/kernel/signal.c +++ linux/arch/i386/kernel/signal.c @@ -533,6 +533,13 @@ handle_signal(unsigned long sig, siginfo } } +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + local_irq_enable(); + preempt_check_resched(); +#endif /* * If TF is set due to a debugger (PT_DTRACE), clear the TF flag so * that register information in the sigcontext is correct. @@ -573,6 +580,13 @@ static void fastcall do_signal(struct pt struct k_sigaction ka; sigset_t *oldset; +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + local_irq_enable(); + preempt_check_resched(); +#endif /* * We want the common case to go fast, which * is why we may in certain cases get here from Index: linux/arch/i386/kernel/smp.c =================================================================== --- linux.orig/arch/i386/kernel/smp.c +++ linux/arch/i386/kernel/smp.c @@ -246,7 +246,7 @@ void send_IPI_mask_sequence(cpumask_t ma static cpumask_t flush_cpumask; static struct mm_struct * flush_mm; static unsigned long flush_va; -static DEFINE_SPINLOCK(tlbstate_lock); +static DEFINE_RAW_SPINLOCK(tlbstate_lock); /* * We cannot call mmdrop() because we are in interrupt context, @@ -474,10 +474,20 @@ static void native_smp_send_reschedule(i } /* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them: + */ +void smp_send_reschedule_allbutself(void) +{ + send_IPI_allbutself(RESCHEDULE_VECTOR); +} + +/* * Structure and data for smp_call_function(). This is designed to minimise * static memory requirements. It also looks cleaner. */ -static DEFINE_SPINLOCK(call_lock); +static DEFINE_RAW_SPINLOCK(call_lock); struct call_data_struct { void (*func) (void *info); @@ -632,13 +642,14 @@ static void native_smp_send_stop(void) } /* - * Reschedule call back. Nothing to do, - * all the work is done automatically when - * we return from the interrupt. + * Reschedule call back. Trigger a reschedule pass so that + * RT-overload balancing can pass tasks around. */ -fastcall void smp_reschedule_interrupt(struct pt_regs *regs) +fastcall notrace void smp_reschedule_interrupt(struct pt_regs *regs) { + trace_special(regs->eip, 0, 0); ack_APIC_irq(); + set_tsk_need_resched(current); } fastcall void smp_call_function_interrupt(struct pt_regs *regs) Index: linux/arch/i386/kernel/smpboot.c =================================================================== --- linux.orig/arch/i386/kernel/smpboot.c +++ linux/arch/i386/kernel/smpboot.c @@ -941,17 +941,6 @@ exit: } #endif -static void smp_tune_scheduling(void) -{ - if (cpu_khz) { - /* cache size in kB */ - long cachesize = boot_cpu_data.x86_cache_size; - - if (cachesize > 0) - max_cache_size = cachesize * 1024; - } -} - /* * Cycle through the processors sending APIC IPIs to boot each. */ @@ -980,7 +969,6 @@ static void __init smp_boot_cpus(unsigne x86_cpu_to_apicid[0] = boot_cpu_physical_apicid; current_thread_info()->cpu = 0; - smp_tune_scheduling(); set_cpu_sibling_map(0); Index: linux/arch/i386/kernel/time.c =================================================================== --- linux.orig/arch/i386/kernel/time.c +++ linux/arch/i386/kernel/time.c @@ -124,7 +124,7 @@ static int set_rtc_mmss(unsigned long no int timer_ack; -unsigned long profile_pc(struct pt_regs *regs) +unsigned long notrace profile_pc(struct pt_regs *regs) { unsigned long pc = instruction_pointer(regs); @@ -207,55 +207,9 @@ unsigned long read_persistent_clock(void return retval; } -static void sync_cmos_clock(unsigned long dummy); - -static DEFINE_TIMER(sync_cmos_timer, sync_cmos_clock, 0, 0); -int no_sync_cmos_clock; - -static void sync_cmos_clock(unsigned long dummy) -{ - struct timeval now, next; - int fail = 1; - - /* - * If we have an externally synchronized Linux clock, then update - * CMOS clock accordingly every ~11 minutes. Set_rtc_mmss() has to be - * called as close as possible to 500 ms before the new second starts. - * This code is run on a timer. If the clock is set, that timer - * may not expire at the correct time. Thus, we adjust... - */ - if (!ntp_synced()) - /* - * Not synced, exit, do not restart a timer (if one is - * running, let it run out). - */ - return; - - do_gettimeofday(&now); - if (now.tv_usec >= USEC_AFTER - ((unsigned) TICK_SIZE) / 2 && - now.tv_usec <= USEC_BEFORE + ((unsigned) TICK_SIZE) / 2) - fail = set_rtc_mmss(now.tv_sec); - - next.tv_usec = USEC_AFTER - now.tv_usec; - if (next.tv_usec <= 0) - next.tv_usec += USEC_PER_SEC; - - if (!fail) - next.tv_sec = 659; - else - next.tv_sec = 0; - - if (next.tv_usec >= USEC_PER_SEC) { - next.tv_sec++; - next.tv_usec -= USEC_PER_SEC; - } - mod_timer(&sync_cmos_timer, jiffies + timeval_to_jiffies(&next)); -} - -void notify_arch_cmos_timer(void) +int update_persistent_clock(struct timespec now) { - if (!no_sync_cmos_clock) - mod_timer(&sync_cmos_timer, jiffies + 1); + return set_rtc_mmss(now.tv_sec); } extern void (*late_time_init)(void); Index: linux/arch/i386/kernel/traps.c =================================================================== --- linux.orig/arch/i386/kernel/traps.c +++ linux/arch/i386/kernel/traps.c @@ -222,6 +222,7 @@ show_trace_log_lvl(struct task_struct *t { dump_trace(task, regs, stack, &print_trace_ops, log_lvl); printk("%s =======================\n", log_lvl); + print_traces(task); } void show_trace(struct task_struct *task, struct pt_regs *regs, @@ -251,8 +252,15 @@ static void show_stack_log_lvl(struct ta printk("\n%s ", log_lvl); printk("%08lx ", *stack++); } + + pause_on_oops_head(); + printk("\n%sCall Trace:\n", log_lvl); show_trace_log_lvl(task, regs, esp, log_lvl); + + pause_on_oops_tail(); + + debug_show_held_locks(task); } void show_stack(struct task_struct *task, unsigned long *esp) @@ -273,6 +281,12 @@ void dump_stack(void) EXPORT_SYMBOL(dump_stack); +#if defined(CONFIG_DEBUG_STACKOVERFLOW) && defined(CONFIG_EVENT_TRACE) +extern unsigned long worst_stack_left; +#else +# define worst_stack_left -1L +#endif + void show_registers(struct pt_regs *regs) { int i; @@ -301,8 +315,12 @@ void show_registers(struct pt_regs *regs regs->eax, regs->ebx, regs->ecx, regs->edx); printk(KERN_EMERG "esi: %08lx edi: %08lx ebp: %08lx esp: %08lx\n", regs->esi, regs->edi, regs->ebp, esp); - printk(KERN_EMERG "ds: %04x es: %04x fs: %04x gs: %04x ss: %04x\n", - regs->xds & 0xffff, regs->xes & 0xffff, regs->xfs & 0xffff, gs, ss); + + printk(KERN_EMERG "ds: %04x es: %04x fs: %04x gs: %04x ss: %04x " + " preempt:%08x\n", + regs->xds & 0xffff, regs->xes & 0xffff, regs->xfs & 0xffff, gs, + ss, preempt_count()); + printk(KERN_EMERG "Process %.*s (pid: %d, ti=%p task=%p task.ti=%p)", TASK_COMM_LEN, current->comm, current->pid, current_thread_info(), current, task_thread_info(current)); @@ -362,11 +380,11 @@ int is_valid_bugaddr(unsigned long eip) void die(const char * str, struct pt_regs * regs, long err) { static struct { - spinlock_t lock; + raw_spinlock_t lock; u32 lock_owner; int lock_owner_depth; } die = { - .lock = __SPIN_LOCK_UNLOCKED(die.lock), + .lock = RAW_SPIN_LOCK_UNLOCKED(die.lock), .lock_owner = -1, .lock_owner_depth = 0 }; @@ -472,6 +490,11 @@ static void __kprobes do_trap(int trapnr if (!user_mode(regs)) goto kernel_trap; +#ifdef CONFIG_PREEMPT_RT + local_irq_enable(); + preempt_check_resched(); +#endif + trap_signal: { /* * We want error_code and trap_no set for userspace faults and @@ -711,10 +734,11 @@ void __kprobes die_nmi(struct pt_regs *r crash_kexec(regs); } + nmi_exit(); do_exit(SIGSEGV); } -static __kprobes void default_do_nmi(struct pt_regs * regs) +static notrace __kprobes void default_do_nmi(struct pt_regs * regs) { unsigned char reason = 0; @@ -752,11 +776,12 @@ static __kprobes void default_do_nmi(str reassert_nmi(); } -fastcall __kprobes void do_nmi(struct pt_regs * regs, long error_code) +fastcall notrace __kprobes void do_nmi(struct pt_regs * regs, long error_code) { int cpu; nmi_enter(); + nmi_trace((unsigned long)do_nmi, regs->eip, regs->eflags); cpu = smp_processor_id(); Index: linux/arch/i386/kernel/tsc.c =================================================================== --- linux.orig/arch/i386/kernel/tsc.c +++ linux/arch/i386/kernel/tsc.c @@ -4,6 +4,7 @@ * See comments there for proper credits. */ +#include #include #include #include @@ -106,8 +107,13 @@ unsigned long long sched_clock(void) /* * Fall back to jiffies if there's no TSC available: + * ( But note that we still use it if the TSC is marked + * unstable. We do this because unlike Time Of Day, + * the scheduler clock tolerates small errors and it's + * very important for it to be as fast as the platform + * can achive it. ) */ - if (unlikely(!tsc_enabled)) + if (unlikely(!tsc_enabled && !tsc_unstable)) /* No locking but a rare wrong value is not a big deal: */ return (jiffies_64 - INITIAL_JIFFIES) * (1000000000 / HZ); @@ -255,7 +261,7 @@ core_initcall(cpufreq_tsc); static unsigned long current_tsc_khz = 0; -static cycle_t read_tsc(void) +static notrace cycle_t read_tsc(void) { cycle_t ret; @@ -277,6 +283,7 @@ static struct clocksource clocksource_ts void mark_tsc_unstable(char *reason) { + sched_clock_unstable_event(); if (!tsc_unstable) { tsc_unstable = 1; tsc_enabled = 0; Index: linux/arch/i386/kernel/vm86.c =================================================================== --- linux.orig/arch/i386/kernel/vm86.c +++ linux/arch/i386/kernel/vm86.c @@ -137,6 +137,7 @@ struct pt_regs * fastcall save_v86_state local_irq_enable(); if (!current->thread.vm86_info) { + local_irq_disable(); printk("no vm86_info: BAD\n"); do_exit(SIGSEGV); } Index: linux/arch/i386/kernel/vmiclock.c =================================================================== --- linux.orig/arch/i386/kernel/vmiclock.c +++ linux/arch/i386/kernel/vmiclock.c @@ -32,6 +32,7 @@ #include #include #include +#include #include #include "io_ports.h" Index: linux/arch/i386/lib/delay.c =================================================================== --- linux.orig/arch/i386/lib/delay.c +++ linux/arch/i386/lib/delay.c @@ -23,7 +23,7 @@ #endif /* simple loop based delay: */ -static void delay_loop(unsigned long loops) +static notrace void delay_loop(unsigned long loops) { int d0; @@ -38,7 +38,7 @@ static void delay_loop(unsigned long loo } /* TSC based delay: */ -static void delay_tsc(unsigned long loops) +static notrace void delay_tsc(unsigned long loops) { unsigned long bclock, now; @@ -69,7 +69,7 @@ int read_current_timer(unsigned long *ti return -1; } -void __delay(unsigned long loops) +void notrace __delay(unsigned long loops) { delay_fn(loops); } Index: linux/arch/i386/lib/semaphore.S =================================================================== --- linux.orig/arch/i386/lib/semaphore.S +++ linux/arch/i386/lib/semaphore.S @@ -30,7 +30,7 @@ * value or just clobbered.. */ .section .sched.text -ENTRY(__down_failed) +ENTRY(__compat_down_failed) CFI_STARTPROC FRAME pushl %edx @@ -39,7 +39,7 @@ ENTRY(__down_failed) pushl %ecx CFI_ADJUST_CFA_OFFSET 4 CFI_REL_OFFSET ecx,0 - call __down + call __compat_down popl %ecx CFI_ADJUST_CFA_OFFSET -4 CFI_RESTORE ecx @@ -49,9 +49,9 @@ ENTRY(__down_failed) ENDFRAME ret CFI_ENDPROC - END(__down_failed) + END(__compat_down_failed) -ENTRY(__down_failed_interruptible) +ENTRY(__compat_down_failed_interruptible) CFI_STARTPROC FRAME pushl %edx @@ -60,7 +60,7 @@ ENTRY(__down_failed_interruptible) pushl %ecx CFI_ADJUST_CFA_OFFSET 4 CFI_REL_OFFSET ecx,0 - call __down_interruptible + call __compat_down_interruptible popl %ecx CFI_ADJUST_CFA_OFFSET -4 CFI_RESTORE ecx @@ -70,9 +70,9 @@ ENTRY(__down_failed_interruptible) ENDFRAME ret CFI_ENDPROC - END(__down_failed_interruptible) + END(__compat_down_failed_interruptible) -ENTRY(__down_failed_trylock) +ENTRY(__compat_down_failed_trylock) CFI_STARTPROC FRAME pushl %edx @@ -81,7 +81,7 @@ ENTRY(__down_failed_trylock) pushl %ecx CFI_ADJUST_CFA_OFFSET 4 CFI_REL_OFFSET ecx,0 - call __down_trylock + call __compat_down_trylock popl %ecx CFI_ADJUST_CFA_OFFSET -4 CFI_RESTORE ecx @@ -91,9 +91,9 @@ ENTRY(__down_failed_trylock) ENDFRAME ret CFI_ENDPROC - END(__down_failed_trylock) + END(__compat_down_failed_trylock) -ENTRY(__up_wakeup) +ENTRY(__compat_up_wakeup) CFI_STARTPROC FRAME pushl %edx @@ -102,7 +102,7 @@ ENTRY(__up_wakeup) pushl %ecx CFI_ADJUST_CFA_OFFSET 4 CFI_REL_OFFSET ecx,0 - call __up + call __compat_up popl %ecx CFI_ADJUST_CFA_OFFSET -4 CFI_RESTORE ecx @@ -112,7 +112,7 @@ ENTRY(__up_wakeup) ENDFRAME ret CFI_ENDPROC - END(__up_wakeup) + END(__compat_up_wakeup) /* * rw spinlock fallbacks Index: linux/arch/i386/mach-default/setup.c =================================================================== --- linux.orig/arch/i386/mach-default/setup.c +++ linux/arch/i386/mach-default/setup.c @@ -35,7 +35,7 @@ void __init pre_intr_init_hook(void) /* * IRQ2 is cascade interrupt to second interrupt controller */ -static struct irqaction irq2 = { no_action, 0, CPU_MASK_NONE, "cascade", NULL, NULL}; +static struct irqaction irq2 = { no_action, IRQF_NODELAY, CPU_MASK_NONE, "cascade", NULL, NULL}; /** * intr_init_hook - post gate setup interrupt initialisation @@ -81,7 +81,7 @@ void __init trap_init_hook(void) static struct irqaction irq0 = { .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_IRQPOLL, + .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_IRQPOLL | IRQF_NODELAY, .mask = CPU_MASK_NONE, .name = "timer" }; Index: linux/arch/i386/mach-visws/visws_apic.c =================================================================== --- linux.orig/arch/i386/mach-visws/visws_apic.c +++ linux/arch/i386/mach-visws/visws_apic.c @@ -257,11 +257,13 @@ out_unlock: static struct irqaction master_action = { .handler = piix4_master_intr, .name = "PIIX4-8259", + .flags = IRQF_NODELAY, }; static struct irqaction cascade_action = { .handler = no_action, .name = "cascade", + .flags = IRQF_NODELAY, }; Index: linux/arch/i386/mach-voyager/setup.c =================================================================== --- linux.orig/arch/i386/mach-voyager/setup.c +++ linux/arch/i386/mach-voyager/setup.c @@ -18,7 +18,7 @@ void __init pre_intr_init_hook(void) /* * IRQ2 is cascade interrupt to second interrupt controller */ -static struct irqaction irq2 = { no_action, 0, CPU_MASK_NONE, "cascade", NULL, NULL}; +static struct irqaction irq2 = { no_action, IRQF_NODELAY, CPU_MASK_NONE, "cascade", NULL, NULL}; void __init intr_init_hook(void) { @@ -42,7 +42,7 @@ void __init trap_init_hook(void) static struct irqaction irq0 = { .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_IRQPOLL, + .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_IRQPOLL | IRQF_NODELAY, .mask = CPU_MASK_NONE, .name = "timer" }; Index: linux/arch/i386/mm/fault.c =================================================================== --- linux.orig/arch/i386/mm/fault.c +++ linux/arch/i386/mm/fault.c @@ -295,8 +295,8 @@ static inline int vmalloc_fault(unsigned * bit 3 == 1 means use of reserved bit detected * bit 4 == 1 means fault was an instruction fetch */ -fastcall void __kprobes do_page_fault(struct pt_regs *regs, - unsigned long error_code) +fastcall notrace void __kprobes do_page_fault(struct pt_regs *regs, + unsigned long error_code) { struct task_struct *tsk; struct mm_struct *mm; @@ -306,6 +306,7 @@ fastcall void __kprobes do_page_fault(st /* get the address */ address = read_cr2(); + trace_special(regs->eip, error_code, address); tsk = current; @@ -350,7 +351,7 @@ fastcall void __kprobes do_page_fault(st * If we're in an interrupt, have no user context or are running in an * atomic region then we must not take the fault.. */ - if (in_atomic() || !mm) + if (in_atomic() || !mm || current->pagefault_disabled) goto bad_area_nosemaphore; /* When running in the kernel we expect faults to occur only to @@ -488,6 +489,9 @@ bad_area_nosemaphore: nr = (address - idt_descr.address) >> 3; if (nr == 6) { + stop_trace(); + user_trace_stop(); + zap_rt_locks(); do_invalid_op(regs, 0); return; } Index: linux/arch/i386/mm/highmem.c =================================================================== --- linux.orig/arch/i386/mm/highmem.c +++ linux/arch/i386/mm/highmem.c @@ -3,9 +3,9 @@ void *kmap(struct page *page) { - might_sleep(); if (!PageHighMem(page)) return page_address(page); + might_sleep(); return kmap_high(page); } @@ -18,6 +18,26 @@ void kunmap(struct page *page) kunmap_high(page); } +void kunmap_virt(void *ptr) +{ + struct page *page; + + if ((unsigned long)ptr < PKMAP_ADDR(0)) + return; + page = pte_page(pkmap_page_table[PKMAP_NR((unsigned long)ptr)]); + kunmap(page); +} + +struct page *kmap_to_page(void *ptr) +{ + struct page *page; + + if ((unsigned long)ptr < PKMAP_ADDR(0)) + return virt_to_page(ptr); + page = pte_page(pkmap_page_table[PKMAP_NR((unsigned long)ptr)]); + return page; +} + /* * kmap_atomic/kunmap_atomic is significantly faster than kmap/kunmap because * no global lock is needed and because the kmap code must perform a global TLB @@ -26,16 +46,16 @@ void kunmap(struct page *page) * However when holding an atomic kmap is is not legal to sleep, so atomic * kmaps are appropriate for short, tight code paths only. */ -void *kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot) +void *__kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot) { enum fixed_addresses idx; unsigned long vaddr; - /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ + preempt_disable(); pagefault_disable(); idx = type + KM_TYPE_NR*smp_processor_id(); - BUG_ON(!pte_none(*(kmap_pte-idx))); + WARN_ON_ONCE(!pte_none(*(kmap_pte-idx))); if (!PageHighMem(page)) return page_address(page); @@ -47,12 +67,12 @@ void *kmap_atomic_prot(struct page *page return (void*) vaddr; } -void *kmap_atomic(struct page *page, enum km_type type) +void *__kmap_atomic(struct page *page, enum km_type type) { return kmap_atomic_prot(page, type, kmap_prot); } -void kunmap_atomic(void *kvaddr, enum km_type type) +void __kunmap_atomic(void *kvaddr, enum km_type type) { unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK; enum fixed_addresses idx = type + KM_TYPE_NR*smp_processor_id(); @@ -74,16 +94,18 @@ void kunmap_atomic(void *kvaddr, enum km arch_flush_lazy_mmu_mode(); pagefault_enable(); + preempt_enable(); } /* This is the same as kmap_atomic() but can map memory that doesn't * have a struct page associated with it. */ -void *kmap_atomic_pfn(unsigned long pfn, enum km_type type) +void *__kmap_atomic_pfn(unsigned long pfn, enum km_type type) { enum fixed_addresses idx; unsigned long vaddr; + preempt_disable(); pagefault_disable(); idx = type + KM_TYPE_NR*smp_processor_id(); @@ -94,7 +116,7 @@ void *kmap_atomic_pfn(unsigned long pfn, return (void*) vaddr; } -struct page *kmap_atomic_to_page(void *ptr) +struct page *__kmap_atomic_to_page(void *ptr) { unsigned long idx, vaddr = (unsigned long)ptr; pte_t *pte; @@ -109,6 +131,7 @@ struct page *kmap_atomic_to_page(void *p EXPORT_SYMBOL(kmap); EXPORT_SYMBOL(kunmap); -EXPORT_SYMBOL(kmap_atomic); -EXPORT_SYMBOL(kunmap_atomic); -EXPORT_SYMBOL(kmap_atomic_to_page); +EXPORT_SYMBOL(kunmap_virt); +EXPORT_SYMBOL(__kmap_atomic); +EXPORT_SYMBOL(__kunmap_atomic); +EXPORT_SYMBOL(__kmap_atomic_to_page); Index: linux/arch/i386/mm/init.c =================================================================== --- linux.orig/arch/i386/mm/init.c +++ linux/arch/i386/mm/init.c @@ -47,7 +47,7 @@ unsigned int __VMALLOC_RESERVE = 128 << 20; -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); unsigned long highstart_pfn, highend_pfn; static int noinline do_test_wp_bit(void); @@ -193,7 +193,7 @@ static inline int page_kills_ppro(unsign return 0; } -int page_is_ram(unsigned long pagenr) +int notrace page_is_ram(unsigned long pagenr) { int i; unsigned long addr, end; Index: linux/arch/i386/mm/pgtable.c =================================================================== --- linux.orig/arch/i386/mm/pgtable.c +++ linux/arch/i386/mm/pgtable.c @@ -208,7 +208,7 @@ void pmd_ctor(void *pmd, struct kmem_cac * vmalloc faults work because attached pagetables are never freed. * -- wli */ -DEFINE_SPINLOCK(pgd_lock); +DEFINE_RAW_SPINLOCK(pgd_lock); struct page *pgd_list; static inline void pgd_list_add(pgd_t *pgd) Index: linux/arch/i386/oprofile/Kconfig =================================================================== --- linux.orig/arch/i386/oprofile/Kconfig +++ linux/arch/i386/oprofile/Kconfig @@ -15,3 +15,6 @@ config OPROFILE If unsure, say N. +config PROFILE_NMI + bool + default y Index: linux/arch/i386/pci/Makefile =================================================================== --- linux.orig/arch/i386/pci/Makefile +++ linux/arch/i386/pci/Makefile @@ -4,8 +4,9 @@ obj-$(CONFIG_PCI_BIOS) += pcbios.o obj-$(CONFIG_PCI_MMCONFIG) += mmconfig.o direct.o mmconfig-shared.o obj-$(CONFIG_PCI_DIRECT) += direct.o +obj-$(CONFIG_ACPI) += acpi.o + pci-y := fixup.o -pci-$(CONFIG_ACPI) += acpi.o pci-y += legacy.o irq.o pci-$(CONFIG_X86_VISWS) := visws.o fixup.o Index: linux/arch/i386/pci/common.c =================================================================== --- linux.orig/arch/i386/pci/common.c +++ linux/arch/i386/pci/common.c @@ -52,7 +52,7 @@ int pcibios_scanned; * This interrupt-safe spinlock protects all accesses to PCI * configuration space. */ -DEFINE_SPINLOCK(pci_config_lock); +DEFINE_RAW_SPINLOCK(pci_config_lock); /* * Several buggy motherboards address only 16 devices and mirror Index: linux/arch/i386/pci/direct.c =================================================================== --- linux.orig/arch/i386/pci/direct.c +++ linux/arch/i386/pci/direct.c @@ -220,16 +220,23 @@ static int __init pci_check_type1(void) unsigned int tmp; int works = 0; - local_irq_save(flags); + spin_lock_irqsave(&pci_config_lock, flags); outb(0x01, 0xCFB); tmp = inl(0xCF8); outl(0x80000000, 0xCF8); - if (inl(0xCF8) == 0x80000000 && pci_sanity_check(&pci_direct_conf1)) { - works = 1; + + if (inl(0xCF8) == 0x80000000) { + spin_unlock_irqrestore(&pci_config_lock, flags); + + if (pci_sanity_check(&pci_direct_conf1)) + works = 1; + + spin_lock_irqsave(&pci_config_lock, flags); } outl(tmp, 0xCF8); - local_irq_restore(flags); + + spin_unlock_irqrestore(&pci_config_lock, flags); return works; } @@ -239,17 +246,19 @@ static int __init pci_check_type2(void) unsigned long flags; int works = 0; - local_irq_save(flags); + spin_lock_irqsave(&pci_config_lock, flags); outb(0x00, 0xCFB); outb(0x00, 0xCF8); outb(0x00, 0xCFA); - if (inb(0xCF8) == 0x00 && inb(0xCFA) == 0x00 && - pci_sanity_check(&pci_direct_conf2)) { - works = 1; - } - local_irq_restore(flags); + if (inb(0xCF8) == 0x00 && inb(0xCFA) == 0x00) { + spin_unlock_irqrestore(&pci_config_lock, flags); + + if (pci_sanity_check(&pci_direct_conf2)) + works = 1; + } else + spin_unlock_irqrestore(&pci_config_lock, flags); return works; } Index: linux/arch/i386/pci/pci.h =================================================================== --- linux.orig/arch/i386/pci/pci.h +++ linux/arch/i386/pci/pci.h @@ -78,7 +78,7 @@ struct irq_routing_table { extern unsigned int pcibios_irq_mask; extern int pcibios_scanned; -extern spinlock_t pci_config_lock; +extern raw_spinlock_t pci_config_lock; extern int (*pcibios_enable_irq)(struct pci_dev *dev); extern void (*pcibios_disable_irq)(struct pci_dev *dev); Index: linux/arch/ia64/Kconfig =================================================================== --- linux.orig/arch/ia64/Kconfig +++ linux/arch/ia64/Kconfig @@ -44,6 +44,7 @@ config SWIOTLB config RWSEM_XCHGADD_ALGORITHM bool + depends on !PREEMPT_RT default y config ARCH_HAS_ILOG2_U32 @@ -271,6 +272,69 @@ config SMP If you don't know what to do here, say N. + +config GENERIC_TIME + bool + default y + +config HIGH_RES_TIMERS + bool "High-Resolution Timers" + help + + POSIX timers are available by default. This option enables + high-resolution POSIX timers. With this option the resolution + is at least 1 microsecond. High resolution is not free. If + enabled this option will add a small overhead each time a + timer expires that is not on a 1/HZ tick boundary. If no such + timers are used the overhead is nil. + + This option enables two additional POSIX CLOCKS, + CLOCK_REALTIME_HR and CLOCK_MONOTONIC_HR. Note that this + option does not change the resolution of CLOCK_REALTIME or + CLOCK_MONOTONIC which remain at 1/HZ resolution. + +config HIGH_RES_RESOLUTION + int "High-Resolution-Timer resolution (nanoseconds)" + depends on HIGH_RES_TIMERS + default 1000 + help + + This sets the resolution of timers accessed with + CLOCK_REALTIME_HR and CLOCK_MONOTONIC_HR. Too + fine a resolution (small a number) will usually not + be observable due to normal system latencies. For an + 800 MHZ processor about 10,000 is the recommended maximum + (smallest number). If you don't need that sort of resolution, + higher numbers may generate less overhead. + +choice + prompt "Clock source" + depends on HIGH_RES_TIMERS + default HIGH_RES_TIMER_ITC + help + This option allows you to choose the hardware source in charge + of generating high precision interruptions on your system. + On IA-64 these are: + + + ITC Interval Time Counter 1/CPU clock + HPET High Precision Event Timer ~ (XXX:have to check the spec) + + The ITC timer is available on all the ia64 computers because + it is integrated directly into the processor. However it may not + give correct results on MP machines with processors running + at different clock rates. In this case you may want to use + the HPET if available on your machine. + + +config HIGH_RES_TIMER_ITC + bool "Interval Time Counter/ITC" + +config HIGH_RES_TIMER_HPET + bool "High Precision Event Timer/HPET" + +endchoice + config NR_CPUS int "Maximum number of CPUs (2-1024)" range 2 1024 @@ -323,17 +387,15 @@ config FORCE_CPEI_RETARGET This option it useful to enable this feature on older BIOS's as well. You can also enable this by using boot command line option force_cpei=1. -config PREEMPT - bool "Preemptible Kernel" - help - This option reduces the latency of the kernel when reacting to - real-time or interactive events by allowing a low priority process to - be preempted even if it is in kernel mode executing a system call. - This allows applications to run more reliably even when the system is - under load. +source "kernel/Kconfig.preempt" - Say Y here if you are building a kernel for a desktop, embedded - or real-time system. Say N if you are unsure. +config RWSEM_GENERIC_SPINLOCK + bool + depends on PREEMPT_RT + default y + +config PREEMPT + def_bool y if (PREEMPT_RT || PREEMPT_SOFTIRQS || PREEMPT_HARDIRQS || PREEMPT_VOLUNTARY || PREEMPT_DESKTOP) source "mm/Kconfig" Index: linux/arch/ia64/kernel/asm-offsets.c =================================================================== --- linux.orig/arch/ia64/kernel/asm-offsets.c +++ linux/arch/ia64/kernel/asm-offsets.c @@ -255,6 +255,7 @@ void foo(void) offsetof (struct pal_min_state_area_s, pmsa_xip)); BLANK(); +#ifdef CONFIG_TIME_INTERPOLATION /* used by fsys_gettimeofday in arch/ia64/kernel/fsys.S */ DEFINE(IA64_TIME_INTERPOLATOR_ADDRESS_OFFSET, offsetof (struct time_interpolator, addr)); DEFINE(IA64_TIME_INTERPOLATOR_SOURCE_OFFSET, offsetof (struct time_interpolator, source)); @@ -269,4 +270,5 @@ void foo(void) DEFINE(IA64_TIME_SOURCE_MMIO64, TIME_SOURCE_MMIO64); DEFINE(IA64_TIME_SOURCE_MMIO32, TIME_SOURCE_MMIO32); DEFINE(IA64_TIMESPEC_TV_NSEC_OFFSET, offsetof (struct timespec, tv_nsec)); +#endif } Index: linux/arch/ia64/kernel/entry.S =================================================================== --- linux.orig/arch/ia64/kernel/entry.S +++ linux/arch/ia64/kernel/entry.S @@ -1098,23 +1098,24 @@ skip_rbs_switch: st8 [r2]=r8 st8 [r3]=r10 .work_pending: - tbit.z p6,p0=r31,TIF_NEED_RESCHED // current_thread_info()->need_resched==0? + tbit.nz p6,p0=r31,TIF_NEED_RESCHED // current_thread_info()->need_resched==0? +(p6) br.cond.sptk.few .needresched + tbit.z p6,p0=r31,TIF_NEED_RESCHED_DELAYED // current_thread_info()->need_resched_delayed==0? (p6) br.cond.sptk.few .notify -#ifdef CONFIG_PREEMPT -(pKStk) dep r21=-1,r0,PREEMPT_ACTIVE_BIT,1 + +.needresched: + +(pKStk) br.cond.sptk.many .fromkernel ;; -(pKStk) st4 [r20]=r21 ssm psr.i // enable interrupts -#endif br.call.spnt.many rp=schedule -.ret9: cmp.eq p6,p0=r0,r0 // p6 <- 1 - rsm psr.i // disable interrupts - ;; -#ifdef CONFIG_PREEMPT -(pKStk) adds r20=TI_PRE_COUNT+IA64_TASK_SIZE,r13 +.ret9a: rsm psr.i // disable interrupts ;; -(pKStk) st4 [r20]=r0 // preempt_count() <- 0 -#endif + br.cond.sptk.many .endpreemptdep +.fromkernel: + br.call.spnt.many rp=preempt_schedule_irq +.ret9b: rsm psr.i // disable interrupts +.endpreemptdep: (pLvSys)br.cond.sptk.few .work_pending_syscall_end br.cond.sptk.many .work_processed_kernel // re-check Index: linux/arch/ia64/kernel/fsys.S =================================================================== --- linux.orig/arch/ia64/kernel/fsys.S +++ linux/arch/ia64/kernel/fsys.S @@ -26,6 +26,7 @@ #include "entry.h" +#ifdef CONFIG_TIME_INTERPOLATION /* * See Documentation/ia64/fsys.txt for details on fsyscalls. * @@ -350,6 +351,26 @@ ENTRY(fsys_clock_gettime) br.many .gettime END(fsys_clock_gettime) + +#else // !CONFIG_TIME_INTERPOLATION + +# define fsys_gettimeofday 0 +# define fsys_clock_gettime 0 + +.fail_einval: + mov r8 = EINVAL + mov r10 = -1 + FSYS_RETURN + +.fail_efault: + mov r8 = EFAULT + mov r10 = -1 + FSYS_RETURN + +#endif + + + /* * long fsys_rt_sigprocmask (int how, sigset_t *set, sigset_t *oset, size_t sigsetsize). */ Index: linux/arch/ia64/kernel/iosapic.c =================================================================== --- linux.orig/arch/ia64/kernel/iosapic.c +++ linux/arch/ia64/kernel/iosapic.c @@ -111,7 +111,7 @@ (PAGE_SIZE / sizeof(struct iosapic_rte_info)) #define RTE_PREALLOCATED (1) -static DEFINE_SPINLOCK(iosapic_lock); +static DEFINE_RAW_SPINLOCK(iosapic_lock); /* * These tables map IA-64 vectors to the IOSAPIC pin that generates this @@ -429,6 +429,34 @@ iosapic_startup_level_irq (unsigned int return 0; } +/* + * In the preemptible case mask the IRQ first then handle it and ack it. + */ +#ifdef CONFIG_PREEMPT_HARDIRQS + +static void +iosapic_ack_level_irq (unsigned int irq) +{ + ia64_vector vec = irq_to_vector(irq); + struct iosapic_rte_info *rte; + + move_irq(irq); + mask_irq(irq); + list_for_each_entry(rte, &iosapic_intr_info[vec].rtes, rte_list) + iosapic_eoi(rte->addr, vec); +} + +static void +iosapic_end_level_irq (unsigned int irq) +{ + if (!(irq_desc[irq].status & IRQ_INPROGRESS)) + unmask_irq(irq); +} + +#else /* !CONFIG_PREEMPT_HARDIRQS */ + +#define iosapic_ack_level_irq nop + static void iosapic_end_level_irq (unsigned int irq) { @@ -440,10 +468,12 @@ iosapic_end_level_irq (unsigned int irq) iosapic_eoi(rte->addr, vec); } + +#endif + #define iosapic_shutdown_level_irq mask_irq #define iosapic_enable_level_irq unmask_irq #define iosapic_disable_level_irq mask_irq -#define iosapic_ack_level_irq nop struct irq_chip irq_type_iosapic_level = { .name = "IO-SAPIC-level", Index: linux/arch/ia64/kernel/mca.c =================================================================== --- linux.orig/arch/ia64/kernel/mca.c +++ linux/arch/ia64/kernel/mca.c @@ -320,7 +320,7 @@ ia64_mca_spin(const char *func) typedef struct ia64_state_log_s { - spinlock_t isl_lock; + raw_spinlock_t isl_lock; int isl_index; unsigned long isl_count; ia64_err_rec_t *isl_log[IA64_MAX_LOGS]; /* need space to store header + error log */ Index: linux/arch/ia64/kernel/perfmon.c =================================================================== --- linux.orig/arch/ia64/kernel/perfmon.c +++ linux/arch/ia64/kernel/perfmon.c @@ -280,7 +280,7 @@ typedef struct { */ typedef struct pfm_context { - spinlock_t ctx_lock; /* context protection */ + raw_spinlock_t ctx_lock; /* context protection */ pfm_context_flags_t ctx_flags; /* bitmask of flags (block reason incl.) */ unsigned int ctx_state; /* state: active/inactive (no bitfield) */ @@ -369,7 +369,7 @@ typedef struct pfm_context { * mostly used to synchronize between system wide and per-process */ typedef struct { - spinlock_t pfs_lock; /* lock the structure */ + raw_spinlock_t pfs_lock; /* lock the structure */ unsigned int pfs_task_sessions; /* number of per task sessions */ unsigned int pfs_sys_sessions; /* number of per system wide sessions */ @@ -510,7 +510,7 @@ static pfm_intr_handler_desc_t *pfm_alt static struct proc_dir_entry *perfmon_dir; static pfm_uuid_t pfm_null_uuid = {0,}; -static spinlock_t pfm_buffer_fmt_lock; +static raw_spinlock_t pfm_buffer_fmt_lock; static LIST_HEAD(pfm_buffer_fmt_list); static pmu_config_t *pmu_conf; Index: linux/arch/ia64/kernel/process.c =================================================================== --- linux.orig/arch/ia64/kernel/process.c +++ linux/arch/ia64/kernel/process.c @@ -94,6 +94,9 @@ show_stack (struct task_struct *task, un void dump_stack (void) { + if (irqs_disabled()) { + printk("Uh oh.. entering dump_stack() with irqs disabled.\n"); + } show_stack(NULL, NULL); } @@ -197,7 +200,7 @@ void default_idle (void) { local_irq_enable(); - while (!need_resched()) { + while (!need_resched() && !need_resched_delayed()) { if (can_do_pal_halt) safe_halt(); else @@ -281,7 +284,7 @@ cpu_idle (void) current_thread_info()->status |= TS_POLLING; } - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { void (*idle)(void); #ifdef CONFIG_SMP min_xtp(); @@ -303,10 +306,11 @@ cpu_idle (void) normal_xtp(); #endif } - preempt_enable_no_resched(); - schedule(); + __preempt_enable_no_resched(); + __schedule(); + preempt_disable(); - check_pgt_cache(); + if (cpu_is_offline(cpu)) play_dead(); } Index: linux/arch/ia64/kernel/sal.c =================================================================== --- linux.orig/arch/ia64/kernel/sal.c +++ linux/arch/ia64/kernel/sal.c @@ -18,7 +18,7 @@ #include #include - __cacheline_aligned DEFINE_SPINLOCK(sal_lock); + __cacheline_aligned DEFINE_RAW_SPINLOCK(sal_lock); unsigned long sal_platform_features; unsigned short sal_revision; Index: linux/arch/ia64/kernel/salinfo.c =================================================================== --- linux.orig/arch/ia64/kernel/salinfo.c +++ linux/arch/ia64/kernel/salinfo.c @@ -140,7 +140,7 @@ enum salinfo_state { struct salinfo_data { cpumask_t cpu_event; /* which cpus have outstanding events */ - struct semaphore mutex; + struct compat_semaphore mutex; u8 *log_buffer; u64 log_size; u8 *oemdata; /* decoded oem data */ @@ -156,8 +156,8 @@ struct salinfo_data { static struct salinfo_data salinfo_data[ARRAY_SIZE(salinfo_log_name)]; -static DEFINE_SPINLOCK(data_lock); -static DEFINE_SPINLOCK(data_saved_lock); +static DEFINE_RAW_SPINLOCK(data_lock); +static DEFINE_RAW_SPINLOCK(data_saved_lock); /** salinfo_platform_oemdata - optional callback to decode oemdata from an error * record. Index: linux/arch/ia64/kernel/semaphore.c =================================================================== --- linux.orig/arch/ia64/kernel/semaphore.c +++ linux/arch/ia64/kernel/semaphore.c @@ -40,12 +40,12 @@ */ void -__up (struct semaphore *sem) +__up (struct compat_semaphore *sem) { wake_up(&sem->wait); } -void __sched __down (struct semaphore *sem) +void __sched __down (struct compat_semaphore *sem) { struct task_struct *tsk = current; DECLARE_WAITQUEUE(wait, tsk); @@ -82,7 +82,7 @@ void __sched __down (struct semaphore *s tsk->state = TASK_RUNNING; } -int __sched __down_interruptible (struct semaphore * sem) +int __sched __down_interruptible (struct compat_semaphore * sem) { int retval = 0; struct task_struct *tsk = current; @@ -142,7 +142,7 @@ int __sched __down_interruptible (struct * count. */ int -__down_trylock (struct semaphore *sem) +__down_trylock (struct compat_semaphore *sem) { unsigned long flags; int sleepers; Index: linux/arch/ia64/kernel/setup.c =================================================================== --- linux.orig/arch/ia64/kernel/setup.c +++ linux/arch/ia64/kernel/setup.c @@ -805,7 +805,6 @@ static void __cpuinit get_max_cacheline_size (void) { unsigned long line_size, max = 1; - unsigned int cache_size = 0; u64 l, levels, unique_caches; pal_cache_config_info_t cci; s64 status; @@ -835,8 +834,6 @@ get_max_cacheline_size (void) line_size = 1 << cci.pcci_line_size; if (line_size > max) max = line_size; - if (cache_size < cci.pcci_cache_size) - cache_size = cci.pcci_cache_size; if (!cci.pcci_unified) { status = ia64_pal_cache_config_info(l, /* cache_type (instruction)= */ 1, @@ -853,9 +850,6 @@ get_max_cacheline_size (void) ia64_i_cache_stride_shift = cci.pcci_stride; } out: -#ifdef CONFIG_SMP - max_cache_size = max(max_cache_size, cache_size); -#endif if (max > ia64_max_cacheline_size) ia64_max_cacheline_size = max; } Index: linux/arch/ia64/kernel/signal.c =================================================================== --- linux.orig/arch/ia64/kernel/signal.c +++ linux/arch/ia64/kernel/signal.c @@ -446,6 +446,14 @@ ia64_do_signal (struct sigscratch *scr, long errno = scr->pt.r8; # define ERR_CODE(c) (IS_IA32_PROCESS(&scr->pt) ? -(c) : (c)) +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + local_irq_enable(); + preempt_check_resched(); +#endif + /* * In the ia64_leave_kernel code path, we want the common case to go fast, which * is why we may in certain cases get here from kernel mode. Just return without Index: linux/arch/ia64/kernel/smp.c =================================================================== --- linux.orig/arch/ia64/kernel/smp.c +++ linux/arch/ia64/kernel/smp.c @@ -261,6 +261,22 @@ smp_send_reschedule (int cpu) } /* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them: + */ +void smp_send_reschedule_allbutself(void) +{ + unsigned int cpu; + + for_each_online_cpu(cpu) { + if (cpu != smp_processor_id()) + platform_send_ipi(cpu, IA64_IPI_RESCHEDULE, + IA64_IPI_DM_INT, 0); + } +} + +/* * Called with preemption disabled. */ static void Index: linux/arch/ia64/kernel/smpboot.c =================================================================== --- linux.orig/arch/ia64/kernel/smpboot.c +++ linux/arch/ia64/kernel/smpboot.c @@ -370,6 +370,8 @@ smp_setup_percpu_timer (void) { } +extern void register_itc_clockevent(void); + static void __cpuinit smp_callin (void) { @@ -444,6 +446,7 @@ smp_callin (void) #ifdef CONFIG_IA32_SUPPORT ia32_gdt_init(); #endif + register_itc_clockevent(); /* * Allow the master to continue. Index: linux/arch/ia64/kernel/time.c =================================================================== --- linux.orig/arch/ia64/kernel/time.c +++ linux/arch/ia64/kernel/time.c @@ -54,6 +54,7 @@ timer_interrupt (int irq, void *dev_id) platform_timer_interrupt(irq, dev_id); +#if 0 new_itm = local_cpu_data->itm_next; if (!time_after(ia64_get_itc(), new_itm)) @@ -61,29 +62,48 @@ timer_interrupt (int irq, void *dev_id) ia64_get_itc(), new_itm); profile_tick(CPU_PROFILING); +#endif + + if (time_after(ia64_get_itc(), local_cpu_data->itm_tick_next)) { - while (1) { - update_process_times(user_mode(get_irq_regs())); + unsigned long new_tick_itm; + new_tick_itm = local_cpu_data->itm_tick_next; - new_itm += local_cpu_data->itm_delta; + profile_tick(CPU_PROFILING, get_irq_regs()); - if (smp_processor_id() == time_keeper_id) { - /* - * Here we are in the timer irq handler. We have irqs locally - * disabled, but we don't know if the timer_bh is running on - * another CPU. We need to avoid to SMP race by acquiring the - * xtime_lock. - */ - write_seqlock(&xtime_lock); - do_timer(1); - local_cpu_data->itm_next = new_itm; - write_sequnlock(&xtime_lock); - } else - local_cpu_data->itm_next = new_itm; + while (1) { + update_process_times(user_mode(get_irq_regs())); + + new_tick_itm += local_cpu_data->itm_tick_delta; + + if (smp_processor_id() == time_keeper_id) { + /* + * Here we are in the timer irq handler. We have irqs locally + * disabled, but we don't know if the timer_bh is running on + * another CPU. We need to avoid to SMP race by acquiring the + * xtime_lock. + */ + write_seqlock(&xtime_lock); + do_timer(get_irq_regs()); + local_cpu_data->itm_tick_next = new_tick_itm; + write_sequnlock(&xtime_lock); + } else + local_cpu_data->itm_tick_next = new_tick_itm; + + if (time_after(new_tick_itm, ia64_get_itc())) + break; + } + } - if (time_after(new_itm, ia64_get_itc())) - break; + if (time_after(ia64_get_itc(), local_cpu_data->itm_timer_next)) { + if (itc_clockevent.event_handler) + itc_clockevent.event_handler(get_irq_regs()); + // FIXME, really, please + new_itm = local_cpu_data->itm_tick_next; + + if (time_after(new_itm, local_cpu_data->itm_timer_next)) + new_itm = local_cpu_data->itm_timer_next; /* * Allow IPIs to interrupt the timer loop. */ @@ -101,8 +121,8 @@ timer_interrupt (int irq, void *dev_id) * too fast (with the potentially devastating effect * of losing monotony of time). */ - while (!time_after(new_itm, ia64_get_itc() + local_cpu_data->itm_delta/2)) - new_itm += local_cpu_data->itm_delta; + while (!time_after(new_itm, ia64_get_itc() + local_cpu_data->itm_tick_delta/2)) + new_itm += local_cpu_data->itm_tick_delta; ia64_set_itm(new_itm); /* double check, in case we got hit by a (slow) PMI: */ } while (time_after_eq(ia64_get_itc(), new_itm)); @@ -121,7 +141,7 @@ ia64_cpu_local_tick (void) /* arrange for the cycle counter to generate a timer interrupt: */ ia64_set_itv(IA64_TIMER_VECTOR); - delta = local_cpu_data->itm_delta; + delta = local_cpu_data->itm_tick_delta; /* * Stagger the timer tick for each CPU so they don't occur all at (almost) the * same time: @@ -130,8 +150,8 @@ ia64_cpu_local_tick (void) unsigned long hi = 1UL << ia64_fls(cpu); shift = (2*(cpu - hi) + 1) * delta/hi/2; } - local_cpu_data->itm_next = ia64_get_itc() + delta + shift; - ia64_set_itm(local_cpu_data->itm_next); + local_cpu_data->itm_tick_next = ia64_get_itc() + delta + shift; + ia64_set_itm(local_cpu_data->itm_tick_next); } static int nojitter; @@ -189,7 +209,7 @@ ia64_init_itm (void) itc_freq = (platform_base_freq*itc_ratio.num)/itc_ratio.den; - local_cpu_data->itm_delta = (itc_freq + HZ/2) / HZ; + local_cpu_data->itm_tick_delta = (itc_freq + HZ/2) / HZ; printk(KERN_DEBUG "CPU %d: base freq=%lu.%03luMHz, ITC ratio=%u/%u, " "ITC freq=%lu.%03luMHz", smp_processor_id(), platform_base_freq / 1000000, (platform_base_freq / 1000) % 1000, @@ -209,6 +229,7 @@ ia64_init_itm (void) local_cpu_data->nsec_per_cyc = ((NSEC_PER_SEC<itc_freq; itc_interpolator.drift = itc_drift; @@ -227,6 +248,7 @@ ia64_init_itm (void) #endif register_time_interpolator(&itc_interpolator); } +#endif /* Setup the CPU local timer tick */ ia64_cpu_local_tick(); @@ -234,7 +256,7 @@ ia64_init_itm (void) static struct irqaction timer_irqaction = { .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_IRQPOLL, + .flags = IRQF_DISABLED | IRQF_IRQPOLL | IRQF_NODELAY, .name = "timer" }; @@ -255,6 +277,8 @@ time_init (void) * tv_nsec field must be normalized (i.e., 0 <= nsec < NSEC_PER_SEC). */ set_normalized_timespec(&wall_to_monotonic, -xtime.tv_sec, -xtime.tv_nsec); + register_itc_clocksource(); + register_itc_clockevent(); } /* Index: linux/arch/ia64/kernel/traps.c =================================================================== --- linux.orig/arch/ia64/kernel/traps.c +++ linux/arch/ia64/kernel/traps.c @@ -39,11 +39,11 @@ void die (const char *str, struct pt_regs *regs, long err) { static struct { - spinlock_t lock; + raw_spinlock_t lock; u32 lock_owner; int lock_owner_depth; } die = { - .lock = __SPIN_LOCK_UNLOCKED(die.lock), + .lock = RAW_SPIN_LOCK_UNLOCKED(die.lock), .lock_owner = -1, .lock_owner_depth = 0 }; @@ -180,7 +180,7 @@ __kprobes ia64_bad_break (unsigned long * access to fph by the time we get here, as the IVT's "Disabled FP-Register" handler takes * care of clearing psr.dfh. */ -static inline void +void disabled_fph_fault (struct pt_regs *regs) { struct ia64_psr *psr = ia64_psr(regs); @@ -199,7 +199,7 @@ disabled_fph_fault (struct pt_regs *regs = (struct task_struct *)ia64_get_kr(IA64_KR_FPU_OWNER); if (ia64_is_local_fpu_owner(current)) { - preempt_enable_no_resched(); + __preempt_enable_no_resched(); return; } @@ -219,7 +219,7 @@ disabled_fph_fault (struct pt_regs *regs */ psr->mfh = 1; } - preempt_enable_no_resched(); + __preempt_enable_no_resched(); } static inline int Index: linux/arch/ia64/kernel/unwind.c =================================================================== --- linux.orig/arch/ia64/kernel/unwind.c +++ linux/arch/ia64/kernel/unwind.c @@ -82,7 +82,7 @@ typedef unsigned long unw_word; typedef unsigned char unw_hash_index_t; static struct { - spinlock_t lock; /* spinlock for unwind data */ + raw_spinlock_t lock; /* spinlock for unwind data */ /* list of unwind tables (one per load-module) */ struct unw_table *tables; @@ -146,7 +146,7 @@ static struct { # endif } unw = { .tables = &unw.kernel_table, - .lock = __SPIN_LOCK_UNLOCKED(unw.lock), + .lock = RAW_SPIN_LOCK_UNLOCKED(unw.lock), .save_order = { UNW_REG_RP, UNW_REG_PFS, UNW_REG_PSP, UNW_REG_PR, UNW_REG_UNAT, UNW_REG_LC, UNW_REG_FPSR, UNW_REG_PRI_UNAT_GR Index: linux/arch/ia64/kernel/unwind_i.h =================================================================== --- linux.orig/arch/ia64/kernel/unwind_i.h +++ linux/arch/ia64/kernel/unwind_i.h @@ -154,7 +154,7 @@ struct unw_script { unsigned long ip; /* ip this script is for */ unsigned long pr_mask; /* mask of predicates script depends on */ unsigned long pr_val; /* predicate values this script is for */ - rwlock_t lock; + raw_rwlock_t lock; unsigned int flags; /* see UNW_FLAG_* in unwind.h */ unsigned short lru_chain; /* used for least-recently-used chain */ unsigned short coll_chain; /* used for hash collisions */ Index: linux/arch/ia64/mm/init.c =================================================================== --- linux.orig/arch/ia64/mm/init.c +++ linux/arch/ia64/mm/init.c @@ -37,7 +37,7 @@ #include #include -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); extern void ia64_tlb_init (void); Index: linux/arch/ia64/mm/tlb.c =================================================================== --- linux.orig/arch/ia64/mm/tlb.c +++ linux/arch/ia64/mm/tlb.c @@ -32,7 +32,7 @@ static struct { } purge; struct ia64_ctx ia64_ctx = { - .lock = __SPIN_LOCK_UNLOCKED(ia64_ctx.lock), + .lock = RAW_SPIN_LOCK_UNLOCKED(ia64_ctx.lock), .next = 1, .max_ctx = ~0U }; Index: linux/arch/mips/Kconfig =================================================================== --- linux.orig/arch/mips/Kconfig +++ linux/arch/mips/Kconfig @@ -259,6 +259,7 @@ config MIPS_SIM config MOMENCO_OCELOT bool "Momentum Ocelot board" select DMA_NONCOHERENT + select NO_SPINLOCK select HW_HAS_PCI select IRQ_CPU select IRQ_CPU_RM7K @@ -673,6 +674,7 @@ source "arch/mips/philips/pnx8550/common endmenu + config RWSEM_GENERIC_SPINLOCK bool default y @@ -680,6 +682,10 @@ config RWSEM_GENERIC_SPINLOCK config RWSEM_XCHGADD_ALGORITHM bool +config ASM_SEMAPHORES + bool + default y + config ARCH_HAS_ILOG2_U32 bool default n @@ -738,6 +744,9 @@ config DMA_NONCOHERENT config DMA_NEED_PCI_MAP_STATE bool +config NO_SPINLOCK + bool + config EARLY_PRINTK bool "Early printk" if EMBEDDED && DEBUG_KERNEL depends on SYS_HAS_EARLY_PRINTK @@ -1775,12 +1784,17 @@ config SECCOMP If unsure, say Y. Only embedded should say N here. -endmenu - -config RWSEM_GENERIC_SPINLOCK +config GENERIC_TIME bool default y +source "kernel/time/Kconfig" + +config CPU_SPEED + int "CPU speed used for clocksource/clockevent calculations" + default 600 +endmenu + config LOCKDEP_SUPPORT bool default y Index: linux/arch/mips/kernel/Makefile =================================================================== --- linux.orig/arch/mips/kernel/Makefile +++ linux/arch/mips/kernel/Makefile @@ -5,7 +5,7 @@ extra-y := head.o init_task.o vmlinux.lds obj-y += cpu-probe.o branch.o entry.o genex.o irq.o process.o \ - ptrace.o reset.o semaphore.o setup.o signal.o syscall.o \ + ptrace.o reset.o setup.o signal.o syscall.o \ time.o topology.o traps.o unaligned.o binfmt_irix-objs := irixelf.o irixinv.o irixioctl.o irixsig.o \ @@ -14,6 +14,8 @@ binfmt_irix-objs := irixelf.o irixinv.o obj-$(CONFIG_STACKTRACE) += stacktrace.o obj-$(CONFIG_MODULES) += mips_ksyms.o module.o +obj-$(CONFIG_ASM_SEMAPHORES) += semaphore.o + obj-$(CONFIG_CPU_R3000) += r2300_fpu.o r2300_switch.o obj-$(CONFIG_CPU_TX39XX) += r2300_fpu.o r2300_switch.o obj-$(CONFIG_CPU_TX49XX) += r4k_fpu.o r4k_switch.o Index: linux/arch/mips/kernel/asm-offsets.c =================================================================== --- linux.orig/arch/mips/kernel/asm-offsets.c +++ linux/arch/mips/kernel/asm-offsets.c @@ -10,9 +10,11 @@ */ #include #include +#include #include #include #include +#include #include #include Index: linux/arch/mips/kernel/entry.S =================================================================== --- linux.orig/arch/mips/kernel/entry.S +++ linux/arch/mips/kernel/entry.S @@ -30,7 +30,7 @@ .align 5 #ifndef CONFIG_PREEMPT FEXPORT(ret_from_exception) - local_irq_disable # preempt stop + raw_local_irq_disable # preempt stop b __ret_from_irq #endif FEXPORT(ret_from_irq) @@ -41,7 +41,7 @@ FEXPORT(__ret_from_irq) beqz t0, resume_kernel resume_userspace: - local_irq_disable # make sure we dont miss an + raw_local_irq_disable # make sure we dont miss an # interrupt setting need_resched # between sampling and return LONG_L a2, TI_FLAGS($28) # current->work @@ -51,7 +51,9 @@ resume_userspace: #ifdef CONFIG_PREEMPT resume_kernel: - local_irq_disable + raw_local_irq_disable + lw t0, kernel_preemption + beqz t0, restore_all lw t0, TI_PRE_COUNT($28) bnez t0, restore_all need_resched: @@ -61,7 +63,9 @@ need_resched: LONG_L t0, PT_STATUS(sp) # Interrupts off? andi t0, 1 beqz t0, restore_all + raw_local_irq_disable jal preempt_schedule_irq + sw zero, TI_PRE_COUNT($28) b need_resched #endif @@ -69,7 +73,7 @@ FEXPORT(ret_from_fork) jal schedule_tail # a0 = struct task_struct *prev FEXPORT(syscall_exit) - local_irq_disable # make sure need_resched and + raw_local_irq_disable # make sure need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) # current->work @@ -140,19 +144,21 @@ FEXPORT(restore_partial) # restore part .set at work_pending: - andi t0, a2, _TIF_NEED_RESCHED # a2 is preloaded with TI_FLAGS + # a2 is preloaded with TI_FLAGS + andi t0, a2, (_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) beqz t0, work_notifysig work_resched: + raw_local_irq_enable t0 jal schedule - local_irq_disable # make sure need_resched and + raw_local_irq_disable # make sure need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) andi t0, a2, _TIF_WORK_MASK # is there any work to be done # other than syscall tracing? beqz t0, restore_all - andi t0, a2, _TIF_NEED_RESCHED + andi t0, a2, (_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) bnez t0, work_resched work_notifysig: # deal with pending signals and @@ -168,7 +174,7 @@ syscall_exit_work: li t0, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT and t0, a2 # a2 is preloaded with TI_FLAGS beqz t0, work_pending # trace bit set? - local_irq_enable # could let do_syscall_trace() + raw_local_irq_enable # could let do_syscall_trace() # call schedule() instead move a0, sp li a1, 1 Index: linux/arch/mips/kernel/i8259.c =================================================================== --- linux.orig/arch/mips/kernel/i8259.c +++ linux/arch/mips/kernel/i8259.c @@ -29,9 +29,9 @@ */ static int i8259A_auto_eoi = -1; -DEFINE_SPINLOCK(i8259A_lock); /* some platforms call this... */ void mask_and_ack_8259A(unsigned int); +DEFINE_RAW_SPINLOCK(i8259A_lock); static struct irq_chip i8259A_chip = { .name = "XT-PIC", Index: linux/arch/mips/kernel/module.c =================================================================== --- linux.orig/arch/mips/kernel/module.c +++ linux/arch/mips/kernel/module.c @@ -40,7 +40,7 @@ struct mips_hi16 { static struct mips_hi16 *mips_hi16_list; static LIST_HEAD(dbe_list); -static DEFINE_SPINLOCK(dbe_lock); +static DEFINE_RAW_SPINLOCK(dbe_lock); void *module_alloc(unsigned long size) { Index: linux/arch/mips/kernel/process.c =================================================================== --- linux.orig/arch/mips/kernel/process.c +++ linux/arch/mips/kernel/process.c @@ -50,7 +50,7 @@ ATTRIB_NORET void cpu_idle(void) { /* endless idle loop with no priority at all */ while (1) { - while (!need_resched()) { + while (!need_resched() && !need_resched_delayed()) { #ifdef CONFIG_SMTC_IDLE_HOOK_DEBUG extern void smtc_idle_loop_hook(void); @@ -59,9 +59,11 @@ ATTRIB_NORET void cpu_idle(void) if (cpu_wait) (*cpu_wait)(); } - preempt_enable_no_resched(); - schedule(); + local_irq_disable(); + __preempt_enable_no_resched(); + __schedule(); preempt_disable(); + local_irq_enable(); } } Index: linux/arch/mips/kernel/scall32-o32.S =================================================================== --- linux.orig/arch/mips/kernel/scall32-o32.S +++ linux/arch/mips/kernel/scall32-o32.S @@ -73,7 +73,7 @@ stack_done: 1: sw v0, PT_R2(sp) # result o32_syscall_exit: - local_irq_disable # make sure need_resched and + raw_local_irq_disable # make sure need_resched and # signals dont change between # sampling and return lw a2, TI_FLAGS($28) # current->work Index: linux/arch/mips/kernel/scall64-64.S =================================================================== --- linux.orig/arch/mips/kernel/scall64-64.S +++ linux/arch/mips/kernel/scall64-64.S @@ -72,7 +72,7 @@ NESTED(handle_sys64, PT_SIZE, sp) 1: sd v0, PT_R2(sp) # result n64_syscall_exit: - local_irq_disable # make sure need_resched and + raw_local_irq_disable # make sure need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) # current->work Index: linux/arch/mips/kernel/scall64-n32.S =================================================================== --- linux.orig/arch/mips/kernel/scall64-n32.S +++ linux/arch/mips/kernel/scall64-n32.S @@ -69,7 +69,7 @@ NESTED(handle_sysn32, PT_SIZE, sp) sd v0, PT_R0(sp) # set flag for syscall restarting 1: sd v0, PT_R2(sp) # result - local_irq_disable # make sure need_resched and + raw_local_irq_disable # make sure need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) # current->work Index: linux/arch/mips/kernel/scall64-o32.S =================================================================== --- linux.orig/arch/mips/kernel/scall64-o32.S +++ linux/arch/mips/kernel/scall64-o32.S @@ -98,7 +98,7 @@ NESTED(handle_sys, PT_SIZE, sp) 1: sd v0, PT_R2(sp) # result o32_syscall_exit: - local_irq_disable # make need_resched and + raw_local_irq_disable # make need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) Index: linux/arch/mips/kernel/semaphore.c =================================================================== --- linux.orig/arch/mips/kernel/semaphore.c +++ linux/arch/mips/kernel/semaphore.c @@ -36,7 +36,7 @@ * sem->count and sem->waking atomic. Scalability isn't an issue because * this lock is used on UP only so it's just an empty variable. */ -static inline int __sem_update_count(struct semaphore *sem, int incr) +static inline int __sem_update_count(struct compat_semaphore *sem, int incr) { int old_count, tmp; @@ -67,7 +67,7 @@ static inline int __sem_update_count(str : "=&r" (old_count), "=&r" (tmp), "=m" (sem->count) : "r" (incr), "m" (sem->count)); } else { - static DEFINE_SPINLOCK(semaphore_lock); + static DEFINE_RAW_SPINLOCK(semaphore_lock); unsigned long flags; spin_lock_irqsave(&semaphore_lock, flags); @@ -80,7 +80,7 @@ static inline int __sem_update_count(str return old_count; } -void __up(struct semaphore *sem) +void __compat_up(struct compat_semaphore *sem) { /* * Note that we incremented count in up() before we came here, @@ -94,7 +94,7 @@ void __up(struct semaphore *sem) wake_up(&sem->wait); } -EXPORT_SYMBOL(__up); +EXPORT_SYMBOL(__compat_up); /* * Note that when we come in to __down or __down_interruptible, @@ -104,7 +104,7 @@ EXPORT_SYMBOL(__up); * Thus it is only when we decrement count from some value > 0 * that we have actually got the semaphore. */ -void __sched __down(struct semaphore *sem) +void __sched __compat_down(struct compat_semaphore *sem) { struct task_struct *tsk = current; DECLARE_WAITQUEUE(wait, tsk); @@ -133,9 +133,9 @@ void __sched __down(struct semaphore *se wake_up(&sem->wait); } -EXPORT_SYMBOL(__down); +EXPORT_SYMBOL(__compat_down); -int __sched __down_interruptible(struct semaphore * sem) +int __sched __compat_down_interruptible(struct compat_semaphore * sem) { int retval = 0; struct task_struct *tsk = current; @@ -165,4 +165,10 @@ int __sched __down_interruptible(struct return retval; } -EXPORT_SYMBOL(__down_interruptible); +EXPORT_SYMBOL(__compat_down_interruptible); + +int fastcall compat_sem_is_locked(struct compat_semaphore *sem) +{ + return (int) atomic_read(&sem->count) < 0; +} +EXPORT_SYMBOL(compat_sem_is_locked); Index: linux/arch/mips/kernel/signal.c =================================================================== --- linux.orig/arch/mips/kernel/signal.c +++ linux/arch/mips/kernel/signal.c @@ -629,6 +629,10 @@ static void do_signal(struct pt_regs *re siginfo_t info; int signr; +#ifdef CONFIG_PREEMPT_RT + local_irq_enable(); + preempt_check_resched(); +#endif /* * We want the common case to go fast, which is why we may in certain * cases get here from kernel mode. Just return without doing anything Index: linux/arch/mips/kernel/signal32.c =================================================================== --- linux.orig/arch/mips/kernel/signal32.c +++ linux/arch/mips/kernel/signal32.c @@ -656,6 +656,10 @@ static int setup_rt_frame_32(struct k_si if (err) goto give_sigsegv; +#ifdef CONFIG_PREEMPT_RT + local_irq_enable(); + preempt_check_resched(); +#endif /* * Arguments to signal handler: * Index: linux/arch/mips/kernel/smp.c =================================================================== --- linux.orig/arch/mips/kernel/smp.c +++ linux/arch/mips/kernel/smp.c @@ -51,16 +51,6 @@ int __cpu_logical_map[NR_CPUS]; /* Map EXPORT_SYMBOL(phys_cpu_present_map); EXPORT_SYMBOL(cpu_online_map); -/* This happens early in bootup, can't really do it better */ -static void smp_tune_scheduling (void) -{ - struct cache_desc *cd = ¤t_cpu_data.scache; - unsigned long cachesize = cd->linesz * cd->sets * cd->ways; - - if (cachesize > max_cache_size) - max_cache_size = cachesize; -} - extern void __init calibrate_delay(void); extern ATTRIB_NORET void cpu_idle(void); @@ -98,7 +88,22 @@ asmlinkage __cpuinit void start_secondar cpu_idle(); } -DEFINE_SPINLOCK(smp_call_lock); +DEFINE_RAW_SPINLOCK(smp_call_lock); + +/* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them. + */ +void smp_send_reschedule_allbutself(void) +{ + int cpu = smp_processor_id(); + int i; + + for (i = 0; i < NR_CPUS; i++) + if (cpu_online(i) && i != cpu) + core_send_ipi(i, SMP_RESCHEDULE_YOURSELF); +} struct call_data_struct *call_data; @@ -228,7 +233,6 @@ void __init smp_prepare_cpus(unsigned in { init_new_context(current, &init_mm); current_thread_info()->cpu = 0; - smp_tune_scheduling(); plat_prepare_cpus(max_cpus); #ifndef CONFIG_HOTPLUG_CPU cpu_present_map = cpu_possible_map; @@ -286,6 +290,8 @@ int setup_profiling_timer(unsigned int m return 0; } +static DEFINE_RAW_SPINLOCK(tlbstate_lock); + static void flush_tlb_all_ipi(void *info) { local_flush_tlb_all(); @@ -343,6 +349,7 @@ static inline void smp_on_each_tlb(void void flush_tlb_mm(struct mm_struct *mm) { preempt_disable(); + spin_lock(&tlbstate_lock); if ((atomic_read(&mm->mm_users) != 1) || (current->mm != mm)) { smp_on_other_tlbs(flush_tlb_mm_ipi, (void *)mm); @@ -352,6 +359,7 @@ void flush_tlb_mm(struct mm_struct *mm) if (smp_processor_id() != i) cpu_context(i, mm) = 0; } + spin_unlock(&tlbstate_lock); local_flush_tlb_mm(mm); preempt_enable(); @@ -375,6 +383,8 @@ void flush_tlb_range(struct vm_area_stru struct mm_struct *mm = vma->vm_mm; preempt_disable(); + spin_lock(&tlbstate_lock); + if ((atomic_read(&mm->mm_users) != 1) || (current->mm != mm)) { struct flush_tlb_data fd; @@ -388,6 +398,7 @@ void flush_tlb_range(struct vm_area_stru if (smp_processor_id() != i) cpu_context(i, mm) = 0; } + spin_unlock(&tlbstate_lock); local_flush_tlb_range(vma, start, end); preempt_enable(); } @@ -418,6 +429,8 @@ static void flush_tlb_page_ipi(void *inf void flush_tlb_page(struct vm_area_struct *vma, unsigned long page) { preempt_disable(); + spin_lock(&tlbstate_lock); + if ((atomic_read(&vma->vm_mm->mm_users) != 1) || (current->mm != vma->vm_mm)) { struct flush_tlb_data fd; @@ -430,6 +443,7 @@ void flush_tlb_page(struct vm_area_struc if (smp_processor_id() != i) cpu_context(i, vma->vm_mm) = 0; } + spin_unlock(&tlbstate_lock); local_flush_tlb_page(vma, page); preempt_enable(); } Index: linux/arch/mips/kernel/time.c =================================================================== --- linux.orig/arch/mips/kernel/time.c +++ linux/arch/mips/kernel/time.c @@ -10,6 +10,11 @@ * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. + * + * This implementation of High Res Timers uses two timers. One is the system + * timer. The second is used for the high res timers. The high res timers + * require the CPU to have count/compare registers. The mips_set_next_event() + * function schedules the next high res timer interrupt. */ #include #include @@ -23,6 +28,7 @@ #include #include #include +#include #include #include @@ -47,7 +53,27 @@ /* * forward reference */ -DEFINE_SPINLOCK(rtc_lock); +DEFINE_RAW_SPINLOCK(rtc_lock); + +/* any missed timer interrupts */ +int missed_timer_count; + +#ifdef CONFIG_HIGH_RES_TIMERS +static void mips_set_next_event(unsigned long evt); +static void mips_set_mode(int mode, void *priv); + +static struct clock_event lapic_clockevent = { + .name = "mips clockevent interface", + .capabilities = CLOCK_CAP_NEXTEVT | CLOCK_CAP_PROFILE | + CLOCK_HAS_IRQHANDLER +#ifdef CONFIG_SMP + | CLOCK_CAP_UPDATE +#endif + , + .shift = 32, + .set_next_event = mips_set_next_event, +}; +#endif /* * By default we provide the null RTC ops @@ -56,6 +82,129 @@ static unsigned long null_rtc_get_time(v { return mktime(2000, 1, 1, 0, 0, 0); } +#ifdef CONFIG_SMP +/* + * We have to synchronize the master CPU with all the slave CPUs + */ +static atomic_t cpus_started; +static atomic_t cpus_ready; +static atomic_t cpus_count; +/* + * Master processor inits + */ +static void sync_cpus_init(int v) +{ + atomic_set(&cpus_count, 0); + mb(); + atomic_set(&cpus_started, v); + mb(); + atomic_set(&cpus_ready, v); + mb(); +} + +/* + * Called by the master processor + */ +static void sync_cpus_master(int v) +{ + atomic_set(&cpus_count, 0); + mb(); + atomic_set(&cpus_started, v); + mb(); + /* Wait here till all other CPUs are now ready */ + while (atomic_read(&cpus_count) != (num_online_cpus() -1) ) + mb(); + atomic_set(&cpus_ready, v); + mb(); +} +/* + * Called by the slave processors + */ +static void sync_cpus_slave(int v) +{ + /* Check if the master has been through this */ + while (atomic_read(&cpus_started) != v) + mb(); + atomic_inc(&cpus_count); + mb(); + while (atomic_read(&cpus_ready) != v) + mb(); +} +/* + * Called by the slave CPUs when done syncing the count register + * with the master processor + */ +static void sync_cpus_slave_exit(int v) +{ + while (atomic_read(&cpus_started) != v) + mb(); + atomic_inc(&cpus_count); + mb(); +} + +#define LOOPS 100 +static u32 c0_count[NR_CPUS]; /* Count register per CPU */ +static u32 c[NR_CPUS][LOOPS + 1]; /* Count register per CPU per loop for syncing */ + +/* + * Slave processors execute this via IPI + */ +static void sync_c0_count_slave(void *info) +{ + int cpus = 1, loop, prev_count = 0, cpu = smp_processor_id(); + unsigned long flags; + u32 diff_count; /* CPU count registers are 32-bit */ + local_irq_save(flags); + + for(loop = 0; loop <= LOOPS; loop++) { + /* Sync with the Master processor */ + sync_cpus_slave(cpus++); + c[cpu][loop] = c0_count[cpu] = read_c0_count(); + mb(); + sync_cpus_slave(cpus++); + diff_count = c0_count[0] - c0_count[cpu]; + diff_count += prev_count; + diff_count += read_c0_count(); + write_c0_count(diff_count); + prev_count = (prev_count >> 1) + + ((int)(c0_count[0] - c0_count[cpu]) >> 1); + } + + /* Slave processor is done syncing count register with Master */ + sync_cpus_slave_exit(cpus++); + printk("SMP: Slave processor %d done syncing count \n", cpu); + local_irq_restore(flags); +} + +/* + * Master kicks off the syncing process + */ +void sync_c0_count_master(void) +{ + int cpus = 0, loop, cpu = smp_processor_id(); + unsigned long flags; + + printk("SMP: Starting to sync the c0 count register ... \n"); + sync_cpus_init(cpus++); + + /* Kick off the slave processors to also start the syncing process */ + smp_call_function(sync_c0_count_slave, NULL, 0, 0); + local_irq_save(flags); + + for (loop = 0; loop <= LOOPS; loop++) { + /* Wait for all the CPUs here */ + sync_cpus_master(cpus++); + c[cpu][loop] = c0_count[cpu] = read_c0_count(); + mb(); + /* Do syncing once more */ + sync_cpus_master(cpus++); + } + sync_cpus_master(cpus++); + local_irq_restore(flags); + + printk("SMP: Syncing process completed accross CPUs ... \n"); +} +#endif /* CONFIG_SMP */ static int null_rtc_set_time(unsigned long sec) { @@ -66,19 +215,30 @@ unsigned long (*rtc_mips_get_time)(void) int (*rtc_mips_set_time)(unsigned long) = null_rtc_set_time; int (*rtc_mips_set_mmss)(unsigned long); - /* how many counter cycles in a jiffy */ static unsigned long cycles_per_jiffy __read_mostly; +static unsigned long hrt_cycles_per_jiffy __read_mostly; + + /* expirelo is the count value for next CPU timer interrupt */ static unsigned int expirelo; - /* * Null timer ack for systems not needing one (e.g. i8254). */ static void null_timer_ack(void) { /* nothing */ } +#ifdef CONFIG_HIGH_RES_TIMERS +/* + * Set the next event + */ +static void mips_set_next_event(unsigned long evt) +{ + write_c0_compare(read_c0_count() + evt); +} +#endif + /* * Null high precision timer functions for systems lacking one. */ @@ -95,13 +255,13 @@ static void c0_timer_ack(void) unsigned int count; /* Ack this timer interrupt and set the next one. */ - expirelo += cycles_per_jiffy; + expirelo += hrt_cycles_per_jiffy; write_c0_compare(expirelo); - /* Check to see if we have missed any timer interrupts. */ - while (((count = read_c0_count()) - expirelo) < 0x7fffffff) { - /* missed_timer_count++; */ - expirelo = count + cycles_per_jiffy; + count = read_c0_count(); + if ((count - expirelo) < 0x7fffffff) { + /* missed_timer_count++; */ + expirelo = count + hrt_cycles_per_jiffy; write_c0_compare(expirelo); } } @@ -127,6 +287,29 @@ void (*mips_timer_ack)(void); /* last time when xtime and rtc are sync'ed up */ static long last_rtc_update; +unsigned long read_persistent_clock(void) +{ + unsigned long sec; + sec = rtc_mips_get_time(); + return sec; +} + +void sync_persistent_clock(struct timespec ts) +{ + if (ntp_synced() && + xtime.tv_sec > last_rtc_update + 660 && + (xtime.tv_nsec / 1000) >= 500000 - ((unsigned) TICK_SIZE) / 2 && + (xtime.tv_nsec / 1000) <= 500000 + ((unsigned) TICK_SIZE) / 2) { + if (rtc_mips_set_mmss(xtime.tv_sec) == 0) { + last_rtc_update = xtime.tv_sec; + } + else { + /* do it again in 60 s */ + last_rtc_update = xtime.tv_sec - 600; + } + } +} + /* * local_timer_interrupt() does profiling and process accounting * on a per-CPU basis. @@ -160,7 +343,7 @@ irqreturn_t timer_interrupt(int irq, voi /* * If we have an externally synchronized Linux clock, then update - * CMOS clock accordingly every ~11 minutes. rtc_mips_set_time() has to be + * CMOS clock accordingly every ~11 minutes. rtc_set_time() has to be * called as close as possible to 500 ms before the new second starts. */ if (ntp_synced() && @@ -228,6 +411,15 @@ static inline int handle_perf_irq (int r !r2; } +#ifdef CONFIG_HIGH_RES_TIMERS +void event_timer_handler(struct pt_regs *regs) +{ + c0_timer_ack(); + if (lapic_clockevent.event_handler) + lapic_clockevent.event_handler(regs,NULL); +} +#endif + asmlinkage void ll_timer_interrupt(int irq) { int r2 = cpu_has_mips_r2; @@ -235,6 +427,16 @@ asmlinkage void ll_timer_interrupt(int i irq_enter(); kstat_this_cpu.irqs[irq]++; + +#ifdef CONFIG_HIGH_RES_TIMERS + /* + * Run the event handler + */ + if (!r2 || (read_c0_cause() & (1 << 26))) + if (lapic_clockevent.event_handler) + lapic_clockevent.event_handler(regs,NULL); +#endif + if (handle_perf_irq(r2)) goto out; @@ -267,7 +469,7 @@ asmlinkage void ll_local_timer_interrupt * b) (optional) calibrate and set the mips_hpt_frequency * (only needed if you intended to use cpu counter as timer interrupt * source) - * 2) setup xtime based on rtc_mips_get_time(). + * 2) setup xtime based on rtc_get_time(). * 3) calculate a couple of cached variables for later usage * 4) plat_timer_setup() - * a) (optional) over-write any choices made above by time_init(). @@ -281,7 +483,7 @@ unsigned int mips_hpt_frequency; static struct irqaction timer_irqaction = { .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_PERCPU, + .flags = IRQF_DISABLED | IRQF_PERCPU | IRQF_NODELAY, .name = "timer", }; @@ -358,6 +560,9 @@ static void __init init_mips_clocksource void __init time_init(void) { +#ifdef CONFIG_HIGH_RES_TIMERS + u64 temp; +#endif if (board_time_init) board_time_init(); @@ -401,6 +606,12 @@ void __init time_init(void) if (!mips_hpt_frequency) mips_hpt_frequency = calibrate_hpt(); +#ifdef CONFIG_HIGH_RES_TIMERS + hrt_cycles_per_jiffy = ( (CONFIG_CPU_SPEED * 1000000) + HZ / 2) / HZ; +#else + hrt_cycles_per_jiffy = cycles_per_jiffy; +#endif + /* Report the high precision timer rate for a reference. */ printk("Using %u.%03u MHz high precision timer.\n", ((mips_hpt_frequency + 500) / 1000) / 1000, Index: linux/arch/mips/kernel/traps.c =================================================================== --- linux.orig/arch/mips/kernel/traps.c +++ linux/arch/mips/kernel/traps.c @@ -309,7 +309,7 @@ void show_registers(struct pt_regs *regs printk("\n"); } -static DEFINE_SPINLOCK(die_lock); +static DEFINE_RAW_SPINLOCK(die_lock); NORET_TYPE void ATTRIB_NORET die(const char * str, struct pt_regs * regs) { Index: linux/arch/mips/mm/fault.c =================================================================== --- linux.orig/arch/mips/mm/fault.c +++ linux/arch/mips/mm/fault.c @@ -68,7 +68,7 @@ asmlinkage void do_page_fault(struct pt_ * If we're in an interrupt or have no user * context, we must not take the fault.. */ - if (in_atomic() || !mm) + if (in_atomic() || !mm || current->pagefault_disabled) goto bad_area_nosemaphore; down_read(&mm->mmap_sem); Index: linux/arch/mips/mm/highmem.c =================================================================== --- linux.orig/arch/mips/mm/highmem.c +++ linux/arch/mips/mm/highmem.c @@ -38,7 +38,7 @@ void *__kmap_atomic(struct page *page, e enum fixed_addresses idx; unsigned long vaddr; - /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ + preempt_disable(); pagefault_disable(); if (!PageHighMem(page)) return page_address(page); @@ -63,6 +63,7 @@ void __kunmap_atomic(void *kvaddr, enum if (vaddr < FIXADDR_START) { // FIXME pagefault_enable(); + preempt_enable(); return; } @@ -78,6 +79,7 @@ void __kunmap_atomic(void *kvaddr, enum #endif pagefault_enable(); + preempt_enable(); } /* @@ -89,6 +91,7 @@ void *kmap_atomic_pfn(unsigned long pfn, enum fixed_addresses idx; unsigned long vaddr; + preempt_disable(); pagefault_disable(); idx = type + KM_TYPE_NR*smp_processor_id(); Index: linux/arch/mips/mm/init.c =================================================================== --- linux.orig/arch/mips/mm/init.c +++ linux/arch/mips/mm/init.c @@ -59,7 +59,7 @@ #endif /* CONFIG_MIPS_MT_SMTC */ -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); /* * We have up to 8 empty zeroed pages so we can map one of the right colour Index: linux/arch/mips/sibyte/cfe/smp.c =================================================================== --- linux.orig/arch/mips/sibyte/cfe/smp.c +++ linux/arch/mips/sibyte/cfe/smp.c @@ -107,4 +107,8 @@ void prom_smp_finish(void) */ void prom_cpus_done(void) { +#ifdef CONFIG_HIGH_RES_TIMERS + extern void sync_c0_count_master(void); + sync_c0_count_master(); +#endif } Index: linux/arch/mips/sibyte/sb1250/irq.c =================================================================== --- linux.orig/arch/mips/sibyte/sb1250/irq.c +++ linux/arch/mips/sibyte/sb1250/irq.c @@ -81,7 +81,7 @@ static struct irq_chip sb1250_irq_type = /* Store the CPU id (not the logical number) */ int sb1250_irq_owner[SB1250_NR_IRQS]; -DEFINE_SPINLOCK(sb1250_imr_lock); +DEFINE_RAW_SPINLOCK(sb1250_imr_lock); void sb1250_mask_irq(int cpu, int irq) { @@ -242,7 +242,7 @@ static irqreturn_t sb1250_dummy_handler static struct irqaction sb1250_dummy_action = { .handler = sb1250_dummy_handler, - .flags = 0, + .flags = IRQF_NODELAY, .mask = CPU_MASK_NONE, .name = "sb1250-private", .next = NULL, @@ -352,6 +352,10 @@ void __init arch_init_irq(void) #ifdef CONFIG_KGDB imask |= STATUSF_IP6; #endif + +#ifdef CONFIG_HIGH_RES_TIMERS + imask |= STATUSF_IP7; +#endif /* Enable necessary IPs, disable the rest */ change_c0_status(ST0_IM, imask); @@ -429,6 +433,10 @@ asmlinkage void plat_irq_dispatch(void) else #endif +#ifdef CONFIG_HIGH_RES_TIMERS + if (pending & CAUSEF_IP7) + event_timer_handler(regs); +#endif if (pending & CAUSEF_IP4) sb1250_timer_interrupt(); Index: linux/arch/mips/sibyte/sb1250/smp.c =================================================================== --- linux.orig/arch/mips/sibyte/sb1250/smp.c +++ linux/arch/mips/sibyte/sb1250/smp.c @@ -59,7 +59,7 @@ void sb1250_smp_finish(void) { extern void sb1250_time_init(void); sb1250_time_init(); - local_irq_enable(); + raw_local_irq_enable(); } /* Index: linux/arch/mips/sibyte/swarm/setup.c =================================================================== --- linux.orig/arch/mips/sibyte/swarm/setup.c +++ linux/arch/mips/sibyte/swarm/setup.c @@ -131,6 +131,12 @@ void __init plat_mem_setup(void) rtc_mips_set_time = m41t81_set_time; } +#ifdef CONFIG_HIGH_RES_TIMERS + /* + * set the mips_hpt_frequency here + */ + mips_hpt_frequency = CONFIG_CPU_SPEED * 1000000; +#endif printk("This kernel optimized for " #ifdef CONFIG_SIMULATION "simulation" Index: linux/arch/powerpc/Kconfig =================================================================== --- linux.orig/arch/powerpc/Kconfig +++ linux/arch/powerpc/Kconfig @@ -31,18 +31,15 @@ config MMU bool default y -config GENERIC_HARDIRQS +config GENERIC_TIME bool default y -config IRQ_PER_CPU +config GENERIC_HARDIRQS bool default y -config RWSEM_GENERIC_SPINLOCK - bool - -config RWSEM_XCHGADD_ALGORITHM +config IRQ_PER_CPU bool default y @@ -347,7 +344,7 @@ config PPC_MM_SLICES config VIRT_CPU_ACCOUNTING bool "Deterministic task and CPU time accounting" - depends on PPC64 + depends on PPC64 && !GENERIC_CLOCKEVENTS default y help Select this option to enable more accurate task and CPU time @@ -406,7 +403,30 @@ config HIGHMEM depends on PPC32 source kernel/Kconfig.hz + +config GENERIC_CLOCKEVENTS + bool "Clock event devices support" + default n + help + Enable support for the clock event devices necessary for the + high-resolution timers and the tickless system support. + NOTE: This is not compatible with the deterministic time accounting + option on PPC64. + +source kernel/time/Kconfig source kernel/Kconfig.preempt + +config RWSEM_GENERIC_SPINLOCK + bool + default y + +config ASM_SEMAPHORES + bool + default y + +config RWSEM_XCHGADD_ALGORITHM + bool + source "fs/Kconfig.binfmt" # We optimistically allocate largepages from the VM, so make the limit Index: linux/arch/powerpc/Kconfig.debug =================================================================== --- linux.orig/arch/powerpc/Kconfig.debug +++ linux/arch/powerpc/Kconfig.debug @@ -2,6 +2,10 @@ menu "Kernel hacking" source "lib/Kconfig.debug" +config TRACE_IRQFLAGS_SUPPORT + bool + default y + config DEBUG_STACKOVERFLOW bool "Check for stack overflows" depends on DEBUG_KERNEL Index: linux/arch/powerpc/boot/Makefile =================================================================== --- linux.orig/arch/powerpc/boot/Makefile +++ linux/arch/powerpc/boot/Makefile @@ -31,6 +31,14 @@ endif BOOTCFLAGS += -I$(obj) -I$(srctree)/$(obj) +ifdef CONFIG_MCOUNT +# do not trace the boot loader +nullstring := +space := $(nullstring) # end of the line +pg_flag = $(nullstring) -pg # end of the line +CFLAGS := $(subst ${pg_flag},${space},${CFLAGS}) +endif + $(obj)/44x.o: BOOTCFLAGS += -mcpu=440 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=440 @@ -55,7 +63,7 @@ obj-wlib := $(addsuffix .o, $(basename $ obj-plat := $(addsuffix .o, $(basename $(addprefix $(obj)/, $(src-plat)))) quiet_cmd_copy_zlib = COPY $@ - cmd_copy_zlib = sed "s@__attribute_used__@@;s@]*\).*@\"\1\"@" $< > $@ + cmd_copy_zlib = sed "s@__attribute_used__@@;s@.include.@@;s@.include.@@;s@.*spin.*lock.*@@;s@.*SPINLOCK.*@@;s@]*\).*@\"\1\"@" $< > $@ quiet_cmd_copy_zlibheader = COPY $@ cmd_copy_zlibheader = sed "s@]*\).*@\"\1\"@" $< > $@ Index: linux/arch/powerpc/kernel/Makefile =================================================================== --- linux.orig/arch/powerpc/kernel/Makefile +++ linux/arch/powerpc/kernel/Makefile @@ -10,10 +10,11 @@ CFLAGS_prom_init.o += -fPIC CFLAGS_btext.o += -fPIC endif -obj-y := semaphore.o cputable.o ptrace.o syscalls.o \ +obj-y := cputable.o ptrace.o syscalls.o \ irq.o align.o signal_32.o pmc.o vdso.o \ init_task.o process.o systbl.o idle.o obj-y += vdso32/ +obj-$(CONFIG_ASM_SEMAPHORES) += semaphore.o obj-$(CONFIG_PPC64) += setup_64.o binfmt_elf32.o sys_ppc32.o \ signal_64.o ptrace32.o \ paca.o cpu_setup_ppc970.o \ Index: linux/arch/powerpc/kernel/asm-offsets.c =================================================================== --- linux.orig/arch/powerpc/kernel/asm-offsets.c +++ linux/arch/powerpc/kernel/asm-offsets.c @@ -273,16 +273,7 @@ int main(void) #endif /* ! CONFIG_PPC64 */ /* datapage offsets for use by vdso */ - DEFINE(CFG_TB_ORIG_STAMP, offsetof(struct vdso_data, tb_orig_stamp)); - DEFINE(CFG_TB_TICKS_PER_SEC, offsetof(struct vdso_data, tb_ticks_per_sec)); - DEFINE(CFG_TB_TO_XS, offsetof(struct vdso_data, tb_to_xs)); - DEFINE(CFG_STAMP_XSEC, offsetof(struct vdso_data, stamp_xsec)); - DEFINE(CFG_TB_UPDATE_COUNT, offsetof(struct vdso_data, tb_update_count)); - DEFINE(CFG_TZ_MINUTEWEST, offsetof(struct vdso_data, tz_minuteswest)); - DEFINE(CFG_TZ_DSTTIME, offsetof(struct vdso_data, tz_dsttime)); DEFINE(CFG_SYSCALL_MAP32, offsetof(struct vdso_data, syscall_map_32)); - DEFINE(WTOM_CLOCK_SEC, offsetof(struct vdso_data, wtom_clock_sec)); - DEFINE(WTOM_CLOCK_NSEC, offsetof(struct vdso_data, wtom_clock_nsec)); #ifdef CONFIG_PPC64 DEFINE(CFG_SYSCALL_MAP64, offsetof(struct vdso_data, syscall_map_64)); DEFINE(TVAL64_TV_SEC, offsetof(struct timeval, tv_sec)); @@ -303,12 +294,6 @@ int main(void) DEFINE(TZONE_TZ_MINWEST, offsetof(struct timezone, tz_minuteswest)); DEFINE(TZONE_TZ_DSTTIME, offsetof(struct timezone, tz_dsttime)); - /* Other bits used by the vdso */ - DEFINE(CLOCK_REALTIME, CLOCK_REALTIME); - DEFINE(CLOCK_MONOTONIC, CLOCK_MONOTONIC); - DEFINE(NSEC_PER_SEC, NSEC_PER_SEC); - DEFINE(CLOCK_REALTIME_RES, TICK_NSEC); - #ifdef CONFIG_BUG DEFINE(BUG_ENTRY_SIZE, sizeof(struct bug_entry)); #endif Index: linux/arch/powerpc/kernel/entry_32.S =================================================================== --- linux.orig/arch/powerpc/kernel/entry_32.S +++ linux/arch/powerpc/kernel/entry_32.S @@ -641,7 +641,7 @@ user_exc_return: /* r10 contains MSR_KE /* Check current_thread_info()->flags */ rlwinm r9,r1,0,0,(31-THREAD_SHIFT) lwz r9,TI_FLAGS(r9) - andi. r0,r9,(_TIF_SIGPENDING|_TIF_RESTORE_SIGMASK|_TIF_NEED_RESCHED) + andi. r0,r9,(_TIF_SIGPENDING|_TIF_RESTORE_SIGMASK|_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) bne do_work restore_user: @@ -863,7 +863,7 @@ global_dbcr0: #endif /* !(CONFIG_4xx || CONFIG_BOOKE) */ do_work: /* r10 contains MSR_KERNEL here */ - andi. r0,r9,_TIF_NEED_RESCHED + andi. r0,r9,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) beq do_user_signal do_resched: /* r10 contains MSR_KERNEL here */ @@ -877,7 +877,7 @@ recheck: MTMSRD(r10) /* disable interrupts */ rlwinm r9,r1,0,0,(31-THREAD_SHIFT) lwz r9,TI_FLAGS(r9) - andi. r0,r9,_TIF_NEED_RESCHED + andi. r0,r9,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) bne- do_resched andi. r0,r9,_TIF_SIGPENDING|_TIF_RESTORE_SIGMASK beq restore_user @@ -989,3 +989,85 @@ machine_check_in_rtas: /* XXX load up BATs and panic */ #endif /* CONFIG_PPC_RTAS */ + +#ifdef CONFIG_MCOUNT +/* + * mcount() is not the same as _mcount(). The callers of mcount() have a + * normal context. The callers of _mcount() do not have a stack frame and + * have not saved the "caller saves" registers. + */ +_GLOBAL(mcount) + stwu r1,-16(r1) + mflr r3 + lis r5,mcount_enabled@ha + lwz r5,mcount_enabled@l(r5) + stw r3,20(r1) + cmpwi r5,0 + beq 1f + /* r3 contains lr (eip), put parent lr (parent_eip) in r4 */ + lwz r4,16(r1) + lwz r4,4(r4) + bl __trace +1: + lwz r0,20(r1) + mtlr r0 + addi r1,r1,16 + blr + +/* + * The -pg flag, which is specified in the case of CONFIG_MCOUNT, causes the + * C compiler to add a call to _mcount() at the start of each function + * preamble, before the stack frame is created. An example of this preamble + * code is: + * + * mflr r0 + * lis r12,-16354 + * stw r0,4(r1) + * addi r0,r12,-19652 + * bl 0xc00034c8 <_mcount> + * mflr r0 + * stwu r1,-16(r1) + */ +_GLOBAL(_mcount) +#define M_STK_SIZE 48 + /* Would not expect to need to save cr, but glibc version of */ + /* _mcount() does, so cautiously saving it here too. */ + stwu r1,-M_STK_SIZE(r1) + stw r3, 12(r1) + stw r4, 16(r1) + stw r5, 20(r1) + stw r6, 24(r1) + mflr r3 /* will use as first arg to __trace() */ + mfcr r4 + lis r5,mcount_enabled@ha + lwz r5,mcount_enabled@l(r5) + cmpwi r5,0 + stw r3, 44(r1) /* lr */ + stw r4, 8(r1) /* cr */ + stw r7, 28(r1) + stw r8, 32(r1) + stw r9, 36(r1) + stw r10,40(r1) + beq 1f + /* r3 contains lr (eip), put parent lr (parent_eip) in r4 */ + lwz r4,M_STK_SIZE+4(r1) + bl __trace +1: + lwz r8, 8(r1) /* cr */ + lwz r9, 44(r1) /* lr */ + lwz r3, 12(r1) + lwz r4, 16(r1) + lwz r5, 20(r1) + mtcrf 0xff,r8 + mtctr r9 + lwz r0, 52(r1) + lwz r6, 24(r1) + lwz r7, 28(r1) + lwz r8, 32(r1) + lwz r9, 36(r1) + lwz r10,40(r1) + addi r1,r1,M_STK_SIZE + mtlr r0 + bctr + +#endif /* CONFIG_MCOUNT */ Index: linux/arch/powerpc/kernel/entry_64.S =================================================================== --- linux.orig/arch/powerpc/kernel/entry_64.S +++ linux/arch/powerpc/kernel/entry_64.S @@ -449,7 +449,8 @@ _GLOBAL(ret_from_except_lite) #ifdef CONFIG_PREEMPT clrrdi r9,r1,THREAD_SHIFT /* current_thread_info() */ - li r0,_TIF_NEED_RESCHED /* bits to check */ + li r0,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) + /* bits to check */ ld r3,_MSR(r1) ld r4,TI_FLAGS(r9) /* Move MSR_PR bit in r3 to _TIF_SIGPENDING position in r0 */ @@ -572,17 +573,22 @@ do_work: rotldi r10,r10,16 mtmsrd r10,1 ld r4,TI_FLAGS(r9) - andi. r0,r4,_TIF_NEED_RESCHED + andi. r0,r4,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) bne 1b b restore user_work: #endif + /* here we are preempting the current task */ + li r0,1 + stb r0,PACASOFTIRQEN(r13) + stb r0,PACAHARDIRQEN(r13) + /* Enable interrupts */ ori r10,r10,MSR_EE mtmsrd r10,1 - andi. r0,r4,_TIF_NEED_RESCHED + andi. r0,r4,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) beq 1f bl .schedule b .ret_from_except_lite @@ -826,3 +832,63 @@ _GLOBAL(enter_prom) ld r0,16(r1) mtlr r0 blr + +#ifdef CONFIG_MCOUNT +/* + * code almost taken from entry_32.S + */ +#define MCOUNT_FRAME_SIZE 32 +_GLOBAL(mcount) + stdu r1,-MCOUNT_FRAME_SIZE(r1) + mflr r3 + + LOAD_REG_ADDR(r5,mcount_enabled) + lwz r5,0(r5) + std r3,MCOUNT_FRAME_SIZE+16(r1) + cmpwi r5,0 + beq 1f + + /* r3 contains lr (eip), put parent lr (parent_eip) in r4 */ + ld r4,MCOUNT_FRAME_SIZE(r1) + ld r4,16(r4) + bl .__trace + nop +1: + ld r0,MCOUNT_FRAME_SIZE+16(r1) + mtlr r0 + addi r1,r1,MCOUNT_FRAME_SIZE + blr + +/* + * Based on glibc-2.4/sysdeps/powerpc/powerpc64/ppc-mcount.S + * + * We don't need to save the parameter-passing registers as gcc takes + * care of that for us. Thus this function looks fairly normal. + * In fact, the generic code would work for us. + */ +_GLOBAL(_mcount) + /* return if we're in real mode. */ + mfmsr r3 + andi. r0,r3,MSR_IR|MSR_DR /* see if relocation is on? */ + beqlr /* if not, do nothing. */ + /* we're in translation mode. keep going. */ + mflr r3 + ld r11,0(r1) /* load back chain ptr */ + stdu r1,-STACK_FRAME_OVERHEAD(r1) + std r3,STACK_FRAME_OVERHEAD+16(r1) + ld r4,16(r11) /* LR in back chain */ + LOAD_REG_ADDR(r5,mcount_enabled) + lwz r5,0(r5) + cmpwi r5,0 /* see if mcount_enabled? */ + beq 1f /* if disabled, then skip */ + + /* r3 contains lr (eip), put parent lr (parent_eip) in r4 */ + bl .__trace + nop +1: + ld r0,STACK_FRAME_OVERHEAD+16(r1) /* restore saved LR */ + mtlr r0 + addi r1,r1,STACK_FRAME_OVERHEAD + blr + +#endif /* CONFIG_MCOUNT */ Index: linux/arch/powerpc/kernel/head_64.S =================================================================== --- linux.orig/arch/powerpc/kernel/head_64.S +++ linux/arch/powerpc/kernel/head_64.S @@ -1391,7 +1391,7 @@ END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISER * handles any interrupts pending at this point. */ ld r3,SOFTE(r1) - bl .local_irq_restore + bl .raw_local_irq_restore b 11f /* Here we have a page fault that hash_page can't handle. */ Index: linux/arch/powerpc/kernel/idle.c =================================================================== --- linux.orig/arch/powerpc/kernel/idle.c +++ linux/arch/powerpc/kernel/idle.c @@ -24,6 +24,7 @@ #include #include #include +#include #include #include @@ -59,7 +60,9 @@ void cpu_idle(void) set_thread_flag(TIF_POLLING_NRFLAG); while (1) { - while (!need_resched() && !cpu_should_die()) { + tick_nohz_stop_sched_tick(); + while (!need_resched() && !need_resched_delayed() && + !cpu_should_die()) { ppc64_runlatch_off(); if (ppc_md.power_save) { @@ -72,7 +75,9 @@ void cpu_idle(void) local_irq_disable(); /* check again after disabling irqs */ - if (!need_resched() && !cpu_should_die()) + if (!need_resched() && + !need_resched_delayed() && + !cpu_should_die()) ppc_md.power_save(); local_irq_enable(); @@ -92,7 +97,10 @@ void cpu_idle(void) ppc64_runlatch_on(); if (cpu_should_die()) cpu_die(); - preempt_enable_no_resched(); + + tick_nohz_restart_sched_tick(); + + __preempt_enable_no_resched(); schedule(); preempt_disable(); } Index: linux/arch/powerpc/kernel/irq.c =================================================================== --- linux.orig/arch/powerpc/kernel/irq.c +++ linux/arch/powerpc/kernel/irq.c @@ -94,8 +94,6 @@ extern atomic_t ipi_sent; #endif #ifdef CONFIG_PPC64 -EXPORT_SYMBOL(irq_desc); - int distribute_irqs = 1; static inline unsigned long get_hard_enabled(void) @@ -114,7 +112,7 @@ static inline void set_soft_enabled(unsi : : "r" (enable), "i" (offsetof(struct paca_struct, soft_enabled))); } -void local_irq_restore(unsigned long en) +void notrace raw_local_irq_restore(unsigned long en) { /* * get_paca()->soft_enabled = en; @@ -405,7 +403,7 @@ EXPORT_SYMBOL(do_softirq); #ifdef CONFIG_PPC_MERGE static LIST_HEAD(irq_hosts); -static DEFINE_SPINLOCK(irq_big_lock); +static DEFINE_RAW_SPINLOCK(irq_big_lock); static DEFINE_PER_CPU(unsigned int, irq_radix_reader); static unsigned int irq_radix_writer; struct irq_map_entry irq_map[NR_IRQS]; Index: linux/arch/powerpc/kernel/pmc.c =================================================================== --- linux.orig/arch/powerpc/kernel/pmc.c +++ linux/arch/powerpc/kernel/pmc.c @@ -37,7 +37,7 @@ static void dummy_perf(struct pt_regs *r } -static DEFINE_SPINLOCK(pmc_owner_lock); +static DEFINE_RAW_SPINLOCK(pmc_owner_lock); static void *pmc_owner_caller; /* mostly for debugging */ perf_irq_t perf_irq = dummy_perf; Index: linux/arch/powerpc/kernel/ppc_ksyms.c =================================================================== --- linux.orig/arch/powerpc/kernel/ppc_ksyms.c +++ linux/arch/powerpc/kernel/ppc_ksyms.c @@ -16,7 +16,6 @@ #include #include -#include #include #include #include @@ -50,7 +49,7 @@ #endif #ifdef CONFIG_PPC64 -EXPORT_SYMBOL(local_irq_restore); +EXPORT_SYMBOL(raw_local_irq_restore); #endif #ifdef CONFIG_PPC32 @@ -175,7 +174,6 @@ EXPORT_SYMBOL(screen_info); #ifdef CONFIG_PPC32 EXPORT_SYMBOL(timer_interrupt); -EXPORT_SYMBOL(irq_desc); EXPORT_SYMBOL(tb_ticks_per_jiffy); EXPORT_SYMBOL(console_drivers); EXPORT_SYMBOL(cacheable_memcpy); Index: linux/arch/powerpc/kernel/rtas.c =================================================================== --- linux.orig/arch/powerpc/kernel/rtas.c +++ linux/arch/powerpc/kernel/rtas.c @@ -36,7 +36,7 @@ #include struct rtas_t rtas = { - .lock = SPIN_LOCK_UNLOCKED + .lock = RAW_SPIN_LOCK_UNLOCKED(lock) }; EXPORT_SYMBOL(rtas); Index: linux/arch/powerpc/kernel/semaphore.c =================================================================== --- linux.orig/arch/powerpc/kernel/semaphore.c +++ linux/arch/powerpc/kernel/semaphore.c @@ -31,7 +31,7 @@ * sem->count = tmp; * return old_count; */ -static inline int __sem_update_count(struct semaphore *sem, int incr) +static inline int __sem_update_count(struct compat_semaphore *sem, int incr) { int old_count, tmp; @@ -50,7 +50,7 @@ static inline int __sem_update_count(str return old_count; } -void __up(struct semaphore *sem) +void __compat_up(struct compat_semaphore *sem) { /* * Note that we incremented count in up() before we came here, @@ -63,7 +63,7 @@ void __up(struct semaphore *sem) __sem_update_count(sem, 1); wake_up(&sem->wait); } -EXPORT_SYMBOL(__up); +EXPORT_SYMBOL(__compat_up); /* * Note that when we come in to __down or __down_interruptible, @@ -73,7 +73,7 @@ EXPORT_SYMBOL(__up); * Thus it is only when we decrement count from some value > 0 * that we have actually got the semaphore. */ -void __sched __down(struct semaphore *sem) +void __sched __compat_down(struct compat_semaphore *sem) { struct task_struct *tsk = current; DECLARE_WAITQUEUE(wait, tsk); @@ -101,9 +101,9 @@ void __sched __down(struct semaphore *se */ wake_up(&sem->wait); } -EXPORT_SYMBOL(__down); +EXPORT_SYMBOL(__compat_down); -int __sched __down_interruptible(struct semaphore * sem) +int __sched __compat_down_interruptible(struct compat_semaphore *sem) { int retval = 0; struct task_struct *tsk = current; @@ -132,4 +132,10 @@ int __sched __down_interruptible(struct wake_up(&sem->wait); return retval; } -EXPORT_SYMBOL(__down_interruptible); +EXPORT_SYMBOL(__compat_down_interruptible); + +int compat_sem_is_locked(struct compat_semaphore *sem) +{ + return (int) atomic_read(&sem->count) < 0; +} +EXPORT_SYMBOL(compat_sem_is_locked); Index: linux/arch/powerpc/kernel/setup_64.c =================================================================== --- linux.orig/arch/powerpc/kernel/setup_64.c +++ linux/arch/powerpc/kernel/setup_64.c @@ -605,3 +605,22 @@ struct ppc_pci_io ppc_pci_io; EXPORT_SYMBOL(ppc_pci_io); #endif /* CONFIG_PPC_INDIRECT_IO */ +#ifdef CONFIG_STACKTRACE +#include +void notrace save_stack_trace(struct stack_trace *trace, + struct task_struct *task) +{ +} +#endif /* CONFIG_STACKTRACE */ + +#ifdef CONFIG_EARLY_PRINTK +void notrace early_printk(const char *fmt, ...) +{ + BUG(); +} +#endif /* CONFIG_EARLY_PRINTK */ + +#ifdef CONFIG_MCOUNT +extern void _mcount(void); +EXPORT_SYMBOL(_mcount); +#endif /* CONFIG_MCOUNT */ Index: linux/arch/powerpc/kernel/smp.c =================================================================== --- linux.orig/arch/powerpc/kernel/smp.c +++ linux/arch/powerpc/kernel/smp.c @@ -126,6 +126,16 @@ void smp_send_reschedule(int cpu) smp_ops->message_pass(cpu, PPC_MSG_RESCHEDULE); } +/* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them: + */ +void smp_send_reschedule_allbutself(void) +{ + smp_ops->message_pass(MSG_ALL_BUT_SELF, PPC_MSG_RESCHEDULE); +} + #ifdef CONFIG_DEBUGGER void smp_send_debugger_break(int cpu) { @@ -162,7 +172,7 @@ void smp_send_stop(void) * static memory requirements. It also looks cleaner. * Stolen from the i386 version. */ -static __cacheline_aligned_in_smp DEFINE_SPINLOCK(call_lock); +static __cacheline_aligned_in_smp DEFINE_RAW_SPINLOCK(call_lock); static struct call_data_struct { void (*func) (void *info); @@ -331,8 +341,6 @@ void smp_call_function_interrupt(void) } } -extern struct gettimeofday_struct do_gtod; - struct thread_info *current_set[NR_CPUS]; DECLARE_PER_CPU(unsigned int, pvr); Index: linux/arch/powerpc/kernel/time.c =================================================================== --- linux.orig/arch/powerpc/kernel/time.c +++ linux/arch/powerpc/kernel/time.c @@ -52,6 +52,7 @@ #include #include #include +#include #include #include @@ -116,8 +117,6 @@ EXPORT_SYMBOL_GPL(rtc_lock); u64 tb_to_ns_scale; unsigned tb_to_ns_shift; -struct gettimeofday_struct do_gtod; - extern struct timezone sys_tz; static long timezone_offset; @@ -127,6 +126,86 @@ unsigned long ppc_tb_freq; static u64 tb_last_jiffy __cacheline_aligned_in_smp; static DEFINE_PER_CPU(u64, last_jiffy); +#ifdef CONFIG_GENERIC_CLOCKEVENTS + +#if defined(CONFIG_40x) || defined(CONFIG_BOOKE) +#define DECREMENTER_MAX 0xffffffff +#else +#define DECREMENTER_MAX 0x7fffffff /* setting MSB triggers an interrupt */ +#endif + +static int decrementer_set_next_event(unsigned long evt, + struct clock_event_device *dev) +{ +#if defined(CONFIG_40x) + mtspr(SPRN_PIT, evt); /* 40x has a hidden PIT auto-reload register */ +#elif defined(CONFIG_BOOKE) + mtspr(SPRN_DECAR, evt); /* Book E has separate auto-reload register */ + set_dec(evt); +#else + set_dec(evt - 1); /* Classic decrementer interrupts at -1 */ +#endif + return 0; +} + +static void decrementer_set_mode(enum clock_event_mode mode, + struct clock_event_device *dev) +{ +#if defined(CONFIG_40x) || defined(CONFIG_BOOKE) + u32 tcr = mfspr(SPRN_TCR); + + tcr |= TCR_DIE; + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + tcr |= TCR_ARE; + break; + case CLOCK_EVT_MODE_ONESHOT: + tcr &= ~TCR_ARE; + break; + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_SHUTDOWN: + tcr &= ~TCR_DIE; + break; + case CLOCK_EVT_MODE_RESUME: + break; + } + mtspr(SPRN_TCR, tcr); + + if (mode == CLOCK_EVT_MODE_PERIODIC) + decrementer_set_next_event(tb_ticks_per_jiffy, dev); +#endif +} + +static struct clock_event_device decrementer_clockevent = { + .name = "decrementer", +#if defined(CONFIG_40x) || defined(CONFIG_BOOKE) + .features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC, +#else + .features = CLOCK_EVT_FEAT_ONESHOT, +#endif + .shift = 32, + .rating = 200, + .irq = -1, + .set_next_event = decrementer_set_next_event, + .set_mode = decrementer_set_mode, +}; + +static DEFINE_PER_CPU(struct clock_event_device, decrementers); + +static void register_decrementer(void) +{ + int cpu = smp_processor_id(); + struct clock_event_device *decrementer = &per_cpu(decrementers, cpu); + + memcpy(decrementer, &decrementer_clockevent, sizeof(*decrementer)); + + decrementer->cpumask = cpumask_of_cpu(cpu); + + clockevents_register_device(decrementer); +} + +#endif /* CONFIG_GENERIC_CLOCKEVENTS */ + #ifdef CONFIG_VIRT_CPU_ACCOUNTING /* * Factors for converting from cputime_t (timebase ticks) to @@ -222,7 +301,7 @@ struct cpu_purr_data { int initialized; /* thread is running */ u64 tb; /* last TB value read */ u64 purr; /* last PURR value read */ - spinlock_t lock; + raw_spinlock_t lock; }; static DEFINE_PER_CPU(struct cpu_purr_data, cpu_purr_data); @@ -312,6 +391,9 @@ void snapshot_timebase(void) { __get_cpu_var(last_jiffy) = get_tb(); snapshot_purr(); +#ifdef CONFIG_GENERIC_CLOCKEVENTS + register_decrementer(); +#endif } void __delay(unsigned long loops) @@ -375,162 +457,8 @@ static __inline__ void timer_check_rtc(v } } -/* - * This version of gettimeofday has microsecond resolution. - */ -static inline void __do_gettimeofday(struct timeval *tv) -{ - unsigned long sec, usec; - u64 tb_ticks, xsec; - struct gettimeofday_vars *temp_varp; - u64 temp_tb_to_xs, temp_stamp_xsec; - - /* - * These calculations are faster (gets rid of divides) - * if done in units of 1/2^20 rather than microseconds. - * The conversion to microseconds at the end is done - * without a divide (and in fact, without a multiply) - */ - temp_varp = do_gtod.varp; - - /* Sampling the time base must be done after loading - * do_gtod.varp in order to avoid racing with update_gtod. - */ - data_barrier(temp_varp); - tb_ticks = get_tb() - temp_varp->tb_orig_stamp; - temp_tb_to_xs = temp_varp->tb_to_xs; - temp_stamp_xsec = temp_varp->stamp_xsec; - xsec = temp_stamp_xsec + mulhdu(tb_ticks, temp_tb_to_xs); - sec = xsec / XSEC_PER_SEC; - usec = (unsigned long)xsec & (XSEC_PER_SEC - 1); - usec = SCALE_XSEC(usec, 1000000); - - tv->tv_sec = sec; - tv->tv_usec = usec; -} - -void do_gettimeofday(struct timeval *tv) -{ - if (__USE_RTC()) { - /* do this the old way */ - unsigned long flags, seq; - unsigned int sec, nsec, usec; - - do { - seq = read_seqbegin_irqsave(&xtime_lock, flags); - sec = xtime.tv_sec; - nsec = xtime.tv_nsec + tb_ticks_since(tb_last_jiffy); - } while (read_seqretry_irqrestore(&xtime_lock, seq, flags)); - usec = nsec / 1000; - while (usec >= 1000000) { - usec -= 1000000; - ++sec; - } - tv->tv_sec = sec; - tv->tv_usec = usec; - return; - } - __do_gettimeofday(tv); -} - -EXPORT_SYMBOL(do_gettimeofday); - -/* - * There are two copies of tb_to_xs and stamp_xsec so that no - * lock is needed to access and use these values in - * do_gettimeofday. We alternate the copies and as long as a - * reasonable time elapses between changes, there will never - * be inconsistent values. ntpd has a minimum of one minute - * between updates. - */ -static inline void update_gtod(u64 new_tb_stamp, u64 new_stamp_xsec, - u64 new_tb_to_xs) -{ - unsigned temp_idx; - struct gettimeofday_vars *temp_varp; - - temp_idx = (do_gtod.var_idx == 0); - temp_varp = &do_gtod.vars[temp_idx]; - - temp_varp->tb_to_xs = new_tb_to_xs; - temp_varp->tb_orig_stamp = new_tb_stamp; - temp_varp->stamp_xsec = new_stamp_xsec; - smp_mb(); - do_gtod.varp = temp_varp; - do_gtod.var_idx = temp_idx; - - /* - * tb_update_count is used to allow the userspace gettimeofday code - * to assure itself that it sees a consistent view of the tb_to_xs and - * stamp_xsec variables. It reads the tb_update_count, then reads - * tb_to_xs and stamp_xsec and then reads tb_update_count again. If - * the two values of tb_update_count match and are even then the - * tb_to_xs and stamp_xsec values are consistent. If not, then it - * loops back and reads them again until this criteria is met. - * We expect the caller to have done the first increment of - * vdso_data->tb_update_count already. - */ - vdso_data->tb_orig_stamp = new_tb_stamp; - vdso_data->stamp_xsec = new_stamp_xsec; - vdso_data->tb_to_xs = new_tb_to_xs; - vdso_data->wtom_clock_sec = wall_to_monotonic.tv_sec; - vdso_data->wtom_clock_nsec = wall_to_monotonic.tv_nsec; - smp_wmb(); - ++(vdso_data->tb_update_count); -} - -/* - * When the timebase - tb_orig_stamp gets too big, we do a manipulation - * between tb_orig_stamp and stamp_xsec. The goal here is to keep the - * difference tb - tb_orig_stamp small enough to always fit inside a - * 32 bits number. This is a requirement of our fast 32 bits userland - * implementation in the vdso. If we "miss" a call to this function - * (interrupt latency, CPU locked in a spinlock, ...) and we end up - * with a too big difference, then the vdso will fallback to calling - * the syscall - */ -static __inline__ void timer_recalc_offset(u64 cur_tb) -{ - unsigned long offset; - u64 new_stamp_xsec; - u64 tlen, t2x; - u64 tb, xsec_old, xsec_new; - struct gettimeofday_vars *varp; - - if (__USE_RTC()) - return; - tlen = current_tick_length(); - offset = cur_tb - do_gtod.varp->tb_orig_stamp; - if (tlen == last_tick_len && offset < 0x80000000u) - return; - if (tlen != last_tick_len) { - t2x = mulhdu(tlen << TICKLEN_SHIFT, ticklen_to_xs); - last_tick_len = tlen; - } else - t2x = do_gtod.varp->tb_to_xs; - new_stamp_xsec = (u64) xtime.tv_nsec * XSEC_PER_SEC; - do_div(new_stamp_xsec, 1000000000); - new_stamp_xsec += (u64) xtime.tv_sec * XSEC_PER_SEC; - - ++vdso_data->tb_update_count; - smp_mb(); - - /* - * Make sure time doesn't go backwards for userspace gettimeofday. - */ - tb = get_tb(); - varp = do_gtod.varp; - xsec_old = mulhdu(tb - varp->tb_orig_stamp, varp->tb_to_xs) - + varp->stamp_xsec; - xsec_new = mulhdu(tb - cur_tb, t2x) + new_stamp_xsec; - if (xsec_new < xsec_old) - new_stamp_xsec += xsec_old - xsec_new; - - update_gtod(cur_tb, new_stamp_xsec, t2x); -} - #ifdef CONFIG_SMP -unsigned long profile_pc(struct pt_regs *regs) +unsigned long notrace profile_pc(struct pt_regs *regs) { unsigned long pc = instruction_pointer(regs); @@ -578,11 +506,7 @@ static void iSeries_tb_recal(void) tb_ticks_per_sec = new_tb_ticks_per_sec; calc_cputime_factors(); div128_by_32( XSEC_PER_SEC, 0, tb_ticks_per_sec, &divres ); - do_gtod.tb_ticks_per_sec = tb_ticks_per_sec; tb_to_xs = divres.result_low; - do_gtod.varp->tb_to_xs = tb_to_xs; - vdso_data->tb_ticks_per_sec = tb_ticks_per_sec; - vdso_data->tb_to_xs = tb_to_xs; } else { printk( "Titan recalibrate: FAILED (difference > 4 percent)\n" @@ -627,7 +551,27 @@ void timer_interrupt(struct pt_regs * re old_regs = set_irq_regs(regs); irq_enter(); +#ifdef CONFIG_GENERIC_CLOCKEVENTS +#if !defined(CONFIG_40x) && !defined(CONFIG_BOOKE) + /* + * We must write a positive value to the decrementer to clear + * the interrupt on POWER4+ compatible CPUs. + */ + set_dec(DECREMENTER_MAX); +#endif + /* + * We can't disable the decrementer, so in the period between + * CPU being marked offline and calling stop-self, it's taking + * timer interrupts... + */ + if (!cpu_is_offline(cpu)) { + struct clock_event_device *dev = &per_cpu(decrementers, cpu); + + dev->event_handler(dev); + } +#else profile_tick(CPU_PROFILING); +#endif calculate_steal_time(); #ifdef CONFIG_PPC_ISERIES @@ -643,6 +587,7 @@ void timer_interrupt(struct pt_regs * re if (__USE_RTC() && per_cpu(last_jiffy, cpu) >= 1000000000) per_cpu(last_jiffy, cpu) -= 1000000000; +#ifndef CONFIG_GENERIC_CLOCKEVENTS /* * We cannot disable the decrementer, so in the period * between this cpu's being marked offline in cpu_online_map @@ -652,6 +597,7 @@ void timer_interrupt(struct pt_regs * re */ if (!cpu_is_offline(cpu)) account_process_time(regs); +#endif /* * No need to check whether cpu is offline here; boot_cpuid @@ -664,15 +610,19 @@ void timer_interrupt(struct pt_regs * re tb_next_jiffy = tb_last_jiffy + tb_ticks_per_jiffy; if (per_cpu(last_jiffy, cpu) >= tb_next_jiffy) { tb_last_jiffy = tb_next_jiffy; +#ifndef CONFIG_GENERIC_CLOCKEVENTS do_timer(1); - timer_recalc_offset(tb_last_jiffy); +#endif + /*timer_recalc_offset(tb_last_jiffy);*/ timer_check_rtc(); } write_sequnlock(&xtime_lock); } - + +#ifndef CONFIG_GENERIC_CLOCKEVENTS next_dec = tb_ticks_per_jiffy - ticks; set_dec(next_dec); +#endif #ifdef CONFIG_PPC_ISERIES if (firmware_has_feature(FW_FEATURE_ISERIES) && hvlpevent_is_pending()) @@ -738,77 +688,6 @@ unsigned long long sched_clock(void) return mulhdu(get_tb(), tb_to_ns_scale) << tb_to_ns_shift; } -int do_settimeofday(struct timespec *tv) -{ - time_t wtm_sec, new_sec = tv->tv_sec; - long wtm_nsec, new_nsec = tv->tv_nsec; - unsigned long flags; - u64 new_xsec; - unsigned long tb_delta; - - if ((unsigned long)tv->tv_nsec >= NSEC_PER_SEC) - return -EINVAL; - - write_seqlock_irqsave(&xtime_lock, flags); - - /* - * Updating the RTC is not the job of this code. If the time is - * stepped under NTP, the RTC will be updated after STA_UNSYNC - * is cleared. Tools like clock/hwclock either copy the RTC - * to the system time, in which case there is no point in writing - * to the RTC again, or write to the RTC but then they don't call - * settimeofday to perform this operation. - */ -#ifdef CONFIG_PPC_ISERIES - if (firmware_has_feature(FW_FEATURE_ISERIES) && first_settimeofday) { - iSeries_tb_recal(); - first_settimeofday = 0; - } -#endif - - /* Make userspace gettimeofday spin until we're done. */ - ++vdso_data->tb_update_count; - smp_mb(); - - /* - * Subtract off the number of nanoseconds since the - * beginning of the last tick. - */ - tb_delta = tb_ticks_since(tb_last_jiffy); - tb_delta = mulhdu(tb_delta, do_gtod.varp->tb_to_xs); /* in xsec */ - new_nsec -= SCALE_XSEC(tb_delta, 1000000000); - - wtm_sec = wall_to_monotonic.tv_sec + (xtime.tv_sec - new_sec); - wtm_nsec = wall_to_monotonic.tv_nsec + (xtime.tv_nsec - new_nsec); - - set_normalized_timespec(&xtime, new_sec, new_nsec); - set_normalized_timespec(&wall_to_monotonic, wtm_sec, wtm_nsec); - - /* In case of a large backwards jump in time with NTP, we want the - * clock to be updated as soon as the PLL is again in lock. - */ - last_rtc_update = new_sec - 658; - - ntp_clear(); - - new_xsec = xtime.tv_nsec; - if (new_xsec != 0) { - new_xsec *= XSEC_PER_SEC; - do_div(new_xsec, NSEC_PER_SEC); - } - new_xsec += (u64)xtime.tv_sec * XSEC_PER_SEC; - update_gtod(tb_last_jiffy, new_xsec, do_gtod.varp->tb_to_xs); - - vdso_data->tz_minuteswest = sys_tz.tz_minuteswest; - vdso_data->tz_dsttime = sys_tz.tz_dsttime; - - write_sequnlock_irqrestore(&xtime_lock, flags); - clock_was_set(); - return 0; -} - -EXPORT_SYMBOL(do_settimeofday); - static int __init get_freq(char *name, int cells, unsigned long *val) { struct device_node *cpu; @@ -864,31 +743,46 @@ void __init generic_calibrate_decr(void) #endif } -unsigned long get_boot_time(void) +unsigned long read_persistent_clock(void) { - struct rtc_time tm; + unsigned long time = 0; + static int first = 1; + + if (first && ppc_md.time_init) { + timezone_offset = ppc_md.time_init(); + + /* If platform provided a timezone (pmac), we correct the time */ + if (timezone_offset) { + sys_tz.tz_minuteswest = -timezone_offset / 60; + sys_tz.tz_dsttime = 0; + } + } if (ppc_md.get_boot_time) - return ppc_md.get_boot_time(); - if (!ppc_md.get_rtc_time) - return 0; - ppc_md.get_rtc_time(&tm); - return mktime(tm.tm_year+1900, tm.tm_mon+1, tm.tm_mday, - tm.tm_hour, tm.tm_min, tm.tm_sec); + time = ppc_md.get_boot_time(); + else if (ppc_md.get_rtc_time) { + struct rtc_time tm; + + ppc_md.get_rtc_time(&tm); + time = mktime(tm.tm_year+1900, tm.tm_mon+1, tm.tm_mday, + tm.tm_hour, tm.tm_min, tm.tm_sec); + } + time -= timezone_offset; + + if (first) { + last_rtc_update = time; + first = 0; + } + return time; } /* This function is only called on the boot processor */ void __init time_init(void) { - unsigned long flags; - unsigned long tm = 0; struct div_result res; u64 scale, x; unsigned shift; - if (ppc_md.time_init != NULL) - timezone_offset = ppc_md.time_init(); - if (__USE_RTC()) { /* 601 processor: dec counts down by 128 every 128ns */ ppc_tb_freq = 1000000000; @@ -961,46 +855,21 @@ void __init time_init(void) tb_to_ns_scale = scale; tb_to_ns_shift = shift; - tm = get_boot_time(); - - write_seqlock_irqsave(&xtime_lock, flags); - - /* If platform provided a timezone (pmac), we correct the time */ - if (timezone_offset) { - sys_tz.tz_minuteswest = -timezone_offset / 60; - sys_tz.tz_dsttime = 0; - tm -= timezone_offset; - } - - xtime.tv_sec = tm; - xtime.tv_nsec = 0; - do_gtod.varp = &do_gtod.vars[0]; - do_gtod.var_idx = 0; - do_gtod.varp->tb_orig_stamp = tb_last_jiffy; - __get_cpu_var(last_jiffy) = tb_last_jiffy; - do_gtod.varp->stamp_xsec = (u64) xtime.tv_sec * XSEC_PER_SEC; - do_gtod.tb_ticks_per_sec = tb_ticks_per_sec; - do_gtod.varp->tb_to_xs = tb_to_xs; - do_gtod.tb_to_us = tb_to_us; - - vdso_data->tb_orig_stamp = tb_last_jiffy; - vdso_data->tb_update_count = 0; - vdso_data->tb_ticks_per_sec = tb_ticks_per_sec; - vdso_data->stamp_xsec = (u64) xtime.tv_sec * XSEC_PER_SEC; - vdso_data->tb_to_xs = tb_to_xs; - - time_freq = 0; - - last_rtc_update = xtime.tv_sec; - set_normalized_timespec(&wall_to_monotonic, - -xtime.tv_sec, -xtime.tv_nsec); - write_sequnlock_irqrestore(&xtime_lock, flags); +#ifdef CONFIG_GENERIC_CLOCKEVENTS + decrementer_clockevent.mult = div_sc(ppc_tb_freq, NSEC_PER_SEC, + decrementer_clockevent.shift); + decrementer_clockevent.max_delta_ns = + clockevent_delta2ns(DECREMENTER_MAX, &decrementer_clockevent); + decrementer_clockevent.min_delta_ns = + clockevent_delta2ns(0xf, &decrementer_clockevent); + register_decrementer(); +#else /* Not exact, but the timer interrupt takes care of this */ set_dec(tb_ticks_per_jiffy); +#endif } - #define FEBRUARY 2 #define STARTOFTIME 1970 #define SECDAY 86400L @@ -1145,3 +1014,39 @@ void div128_by_32(u64 dividend_high, u64 dr->result_low = ((u64)y << 32) + z; } + +/* PowerPC clocksource code */ + +#include + +static cycle_t notrace timebase_read(void) +{ + return (cycle_t)get_tb(); +} + +struct clocksource clocksource_timebase = { + .name = "timebase", + .rating = 200, + .read = timebase_read, + .mask = (cycle_t)-1, + .mult = 0, + .shift = 22, + .flags = CLOCK_SOURCE_IS_CONTINUOUS, +}; + + +/* XXX - this should be calculated or properly externed! */ +static int __init init_timebase_clocksource(void) +{ + if (__USE_RTC()) + return -ENODEV; + +#ifdef CONFIG_PPC64 + clocksource_timebase.shift = tb_ticks_per_jiffy / 1000000; +#endif + clocksource_timebase.mult = clocksource_hz2mult(tb_ticks_per_sec, + clocksource_timebase.shift); + return clocksource_register(&clocksource_timebase); +} + +module_init(init_timebase_clocksource); Index: linux/arch/powerpc/kernel/traps.c =================================================================== --- linux.orig/arch/powerpc/kernel/traps.c +++ linux/arch/powerpc/kernel/traps.c @@ -97,11 +97,11 @@ static inline void pmac_backlight_unblan int die(const char *str, struct pt_regs *regs, long err) { static struct { - spinlock_t lock; + raw_spinlock_t lock; u32 lock_owner; int lock_owner_depth; } die = { - .lock = __SPIN_LOCK_UNLOCKED(die.lock), + .lock = _RAW_SPIN_LOCK_UNLOCKED(die.lock), .lock_owner = -1, .lock_owner_depth = 0 }; @@ -177,6 +177,11 @@ void _exception(int signr, struct pt_reg return; } +#ifdef CONFIG_PREEMPT_RT + local_irq_enable(); + preempt_check_resched(); +#endif + memset(&info, 0, sizeof(info)); info.si_signo = signr; info.si_code = code; Index: linux/arch/powerpc/kernel/vdso32/Makefile =================================================================== --- linux.orig/arch/powerpc/kernel/vdso32/Makefile +++ linux/arch/powerpc/kernel/vdso32/Makefile @@ -1,7 +1,7 @@ # List of files in the vdso, has to be asm only for now -obj-vdso32 = sigtramp.o gettimeofday.o datapage.o cacheflush.o note.o +obj-vdso32 = sigtramp.o datapage.o cacheflush.o note.o # Build rules Index: linux/arch/powerpc/kernel/vdso32/datapage.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso32/datapage.S +++ linux/arch/powerpc/kernel/vdso32/datapage.S @@ -65,21 +65,3 @@ V_FUNCTION_BEGIN(__kernel_get_syscall_ma blr .cfi_endproc V_FUNCTION_END(__kernel_get_syscall_map) - -/* - * void unsigned long long __kernel_get_tbfreq(void); - * - * returns the timebase frequency in HZ - */ -V_FUNCTION_BEGIN(__kernel_get_tbfreq) - .cfi_startproc - mflr r12 - .cfi_register lr,r12 - bl __get_datapage@local - lwz r4,(CFG_TB_TICKS_PER_SEC + 4)(r3) - lwz r3,CFG_TB_TICKS_PER_SEC(r3) - mtlr r12 - crclr cr0*4+so - blr - .cfi_endproc -V_FUNCTION_END(__kernel_get_tbfreq) Index: linux/arch/powerpc/kernel/vdso32/gettimeofday.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso32/gettimeofday.S +++ /dev/null @@ -1,324 +0,0 @@ -/* - * Userland implementation of gettimeofday() for 32 bits processes in a - * ppc64 kernel for use in the vDSO - * - * Copyright (C) 2004 Benjamin Herrenschmuidt (benh@kernel.crashing.org, - * IBM Corp. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ -#include -#include -#include -#include -#include - - .text -/* - * Exact prototype of gettimeofday - * - * int __kernel_gettimeofday(struct timeval *tv, struct timezone *tz); - * - */ -V_FUNCTION_BEGIN(__kernel_gettimeofday) - .cfi_startproc - mflr r12 - .cfi_register lr,r12 - - mr r10,r3 /* r10 saves tv */ - mr r11,r4 /* r11 saves tz */ - bl __get_datapage@local /* get data page */ - mr r9, r3 /* datapage ptr in r9 */ - cmplwi r10,0 /* check if tv is NULL */ - beq 3f - bl __do_get_xsec@local /* get xsec from tb & kernel */ - bne- 2f /* out of line -> do syscall */ - - /* seconds are xsec >> 20 */ - rlwinm r5,r4,12,20,31 - rlwimi r5,r3,12,0,19 - stw r5,TVAL32_TV_SEC(r10) - - /* get remaining xsec and convert to usec. we scale - * up remaining xsec by 12 bits and get the top 32 bits - * of the multiplication - */ - rlwinm r5,r4,12,0,19 - lis r6,1000000@h - ori r6,r6,1000000@l - mulhwu r5,r5,r6 - stw r5,TVAL32_TV_USEC(r10) - -3: cmplwi r11,0 /* check if tz is NULL */ - beq 1f - lwz r4,CFG_TZ_MINUTEWEST(r9)/* fill tz */ - lwz r5,CFG_TZ_DSTTIME(r9) - stw r4,TZONE_TZ_MINWEST(r11) - stw r5,TZONE_TZ_DSTTIME(r11) - -1: mtlr r12 - crclr cr0*4+so - li r3,0 - blr - -2: - mtlr r12 - mr r3,r10 - mr r4,r11 - li r0,__NR_gettimeofday - sc - blr - .cfi_endproc -V_FUNCTION_END(__kernel_gettimeofday) - -/* - * Exact prototype of clock_gettime() - * - * int __kernel_clock_gettime(clockid_t clock_id, struct timespec *tp); - * - */ -V_FUNCTION_BEGIN(__kernel_clock_gettime) - .cfi_startproc - /* Check for supported clock IDs */ - cmpli cr0,r3,CLOCK_REALTIME - cmpli cr1,r3,CLOCK_MONOTONIC - cror cr0*4+eq,cr0*4+eq,cr1*4+eq - bne cr0,99f - - mflr r12 /* r12 saves lr */ - .cfi_register lr,r12 - mr r10,r3 /* r10 saves id */ - mr r11,r4 /* r11 saves tp */ - bl __get_datapage@local /* get data page */ - mr r9,r3 /* datapage ptr in r9 */ - beq cr1,50f /* if monotonic -> jump there */ - - /* - * CLOCK_REALTIME - */ - - bl __do_get_xsec@local /* get xsec from tb & kernel */ - bne- 98f /* out of line -> do syscall */ - - /* seconds are xsec >> 20 */ - rlwinm r5,r4,12,20,31 - rlwimi r5,r3,12,0,19 - stw r5,TSPC32_TV_SEC(r11) - - /* get remaining xsec and convert to nsec. we scale - * up remaining xsec by 12 bits and get the top 32 bits - * of the multiplication, then we multiply by 1000 - */ - rlwinm r5,r4,12,0,19 - lis r6,1000000@h - ori r6,r6,1000000@l - mulhwu r5,r5,r6 - mulli r5,r5,1000 - stw r5,TSPC32_TV_NSEC(r11) - mtlr r12 - crclr cr0*4+so - li r3,0 - blr - - /* - * CLOCK_MONOTONIC - */ - -50: bl __do_get_xsec@local /* get xsec from tb & kernel */ - bne- 98f /* out of line -> do syscall */ - - /* seconds are xsec >> 20 */ - rlwinm r6,r4,12,20,31 - rlwimi r6,r3,12,0,19 - - /* get remaining xsec and convert to nsec. we scale - * up remaining xsec by 12 bits and get the top 32 bits - * of the multiplication, then we multiply by 1000 - */ - rlwinm r7,r4,12,0,19 - lis r5,1000000@h - ori r5,r5,1000000@l - mulhwu r7,r7,r5 - mulli r7,r7,1000 - - /* now we must fixup using wall to monotonic. We need to snapshot - * that value and do the counter trick again. Fortunately, we still - * have the counter value in r8 that was returned by __do_get_xsec. - * At this point, r6,r7 contain our sec/nsec values, r3,r4 and r5 - * can be used - */ - - lwz r3,WTOM_CLOCK_SEC(r9) - lwz r4,WTOM_CLOCK_NSEC(r9) - - /* We now have our result in r3,r4. We create a fake dependency - * on that result and re-check the counter - */ - or r5,r4,r3 - xor r0,r5,r5 - add r9,r9,r0 -#ifdef CONFIG_PPC64 - lwz r0,(CFG_TB_UPDATE_COUNT+4)(r9) -#else - lwz r0,(CFG_TB_UPDATE_COUNT)(r9) -#endif - cmpl cr0,r8,r0 /* check if updated */ - bne- 50b - - /* Calculate and store result. Note that this mimmics the C code, - * which may cause funny results if nsec goes negative... is that - * possible at all ? - */ - add r3,r3,r6 - add r4,r4,r7 - lis r5,NSEC_PER_SEC@h - ori r5,r5,NSEC_PER_SEC@l - cmpl cr0,r4,r5 - cmpli cr1,r4,0 - blt 1f - subf r4,r5,r4 - addi r3,r3,1 -1: bge cr1,1f - addi r3,r3,-1 - add r4,r4,r5 -1: stw r3,TSPC32_TV_SEC(r11) - stw r4,TSPC32_TV_NSEC(r11) - - mtlr r12 - crclr cr0*4+so - li r3,0 - blr - - /* - * syscall fallback - */ -98: - mtlr r12 - mr r3,r10 - mr r4,r11 -99: - li r0,__NR_clock_gettime - sc - blr - .cfi_endproc -V_FUNCTION_END(__kernel_clock_gettime) - - -/* - * Exact prototype of clock_getres() - * - * int __kernel_clock_getres(clockid_t clock_id, struct timespec *res); - * - */ -V_FUNCTION_BEGIN(__kernel_clock_getres) - .cfi_startproc - /* Check for supported clock IDs */ - cmpwi cr0,r3,CLOCK_REALTIME - cmpwi cr1,r3,CLOCK_MONOTONIC - cror cr0*4+eq,cr0*4+eq,cr1*4+eq - bne cr0,99f - - li r3,0 - cmpli cr0,r4,0 - crclr cr0*4+so - beqlr - lis r5,CLOCK_REALTIME_RES@h - ori r5,r5,CLOCK_REALTIME_RES@l - stw r3,TSPC32_TV_SEC(r4) - stw r5,TSPC32_TV_NSEC(r4) - blr - - /* - * syscall fallback - */ -99: - li r0,__NR_clock_getres - sc - blr - .cfi_endproc -V_FUNCTION_END(__kernel_clock_getres) - - -/* - * This is the core of gettimeofday() & friends, it returns the xsec - * value in r3 & r4 and expects the datapage ptr (non clobbered) - * in r9. clobbers r0,r4,r5,r6,r7,r8. - * When returning, r8 contains the counter value that can be reused - * by the monotonic clock implementation - */ -__do_get_xsec: - .cfi_startproc - /* Check for update count & load values. We use the low - * order 32 bits of the update count - */ -#ifdef CONFIG_PPC64 -1: lwz r8,(CFG_TB_UPDATE_COUNT+4)(r9) -#else -1: lwz r8,(CFG_TB_UPDATE_COUNT)(r9) -#endif - andi. r0,r8,1 /* pending update ? loop */ - bne- 1b - xor r0,r8,r8 /* create dependency */ - add r9,r9,r0 - - /* Load orig stamp (offset to TB) */ - lwz r5,CFG_TB_ORIG_STAMP(r9) - lwz r6,(CFG_TB_ORIG_STAMP+4)(r9) - - /* Get a stable TB value */ -2: mftbu r3 - mftbl r4 - mftbu r0 - cmpl cr0,r3,r0 - bne- 2b - - /* Substract tb orig stamp. If the high part is non-zero, we jump to - * the slow path which call the syscall. - * If it's ok, then we have our 32 bits tb_ticks value in r7 - */ - subfc r7,r6,r4 - subfe. r0,r5,r3 - bne- 3f - - /* Load scale factor & do multiplication */ - lwz r5,CFG_TB_TO_XS(r9) /* load values */ - lwz r6,(CFG_TB_TO_XS+4)(r9) - mulhwu r4,r7,r5 - mulhwu r6,r7,r6 - mullw r0,r7,r5 - addc r6,r6,r0 - - /* At this point, we have the scaled xsec value in r4 + XER:CA - * we load & add the stamp since epoch - */ - lwz r5,CFG_STAMP_XSEC(r9) - lwz r6,(CFG_STAMP_XSEC+4)(r9) - adde r4,r4,r6 - addze r3,r5 - - /* We now have our result in r3,r4. We create a fake dependency - * on that result and re-check the counter - */ - or r6,r4,r3 - xor r0,r6,r6 - add r9,r9,r0 -#ifdef CONFIG_PPC64 - lwz r0,(CFG_TB_UPDATE_COUNT+4)(r9) -#else - lwz r0,(CFG_TB_UPDATE_COUNT)(r9) -#endif - cmpl cr0,r8,r0 /* check if updated */ - bne- 1b - - /* Warning ! The caller expects CR:EQ to be set to indicate a - * successful calculation (so it won't fallback to the syscall - * method). We have overriden that CR bit in the counter check, - * but fortunately, the loop exit condition _is_ CR:EQ set, so - * we can exit safely here. If you change this code, be careful - * of that side effect. - */ -3: blr - .cfi_endproc Index: linux/arch/powerpc/kernel/vdso32/vdso32.lds.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso32/vdso32.lds.S +++ linux/arch/powerpc/kernel/vdso32/vdso32.lds.S @@ -117,10 +117,6 @@ VERSION global: __kernel_datapage_offset; /* Has to be there for the kernel to find */ __kernel_get_syscall_map; - __kernel_gettimeofday; - __kernel_clock_gettime; - __kernel_clock_getres; - __kernel_get_tbfreq; __kernel_sync_dicache; __kernel_sync_dicache_p5; __kernel_sigtramp32; Index: linux/arch/powerpc/kernel/vdso64/Makefile =================================================================== --- linux.orig/arch/powerpc/kernel/vdso64/Makefile +++ linux/arch/powerpc/kernel/vdso64/Makefile @@ -1,6 +1,6 @@ # List of files in the vdso, has to be asm only for now -obj-vdso64 = sigtramp.o gettimeofday.o datapage.o cacheflush.o note.o +obj-vdso64 = sigtramp.o datapage.o cacheflush.o note.o # Build rules Index: linux/arch/powerpc/kernel/vdso64/datapage.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso64/datapage.S +++ linux/arch/powerpc/kernel/vdso64/datapage.S @@ -65,21 +65,3 @@ V_FUNCTION_BEGIN(__kernel_get_syscall_ma blr .cfi_endproc V_FUNCTION_END(__kernel_get_syscall_map) - - -/* - * void unsigned long __kernel_get_tbfreq(void); - * - * returns the timebase frequency in HZ - */ -V_FUNCTION_BEGIN(__kernel_get_tbfreq) - .cfi_startproc - mflr r12 - .cfi_register lr,r12 - bl V_LOCAL_FUNC(__get_datapage) - ld r3,CFG_TB_TICKS_PER_SEC(r3) - mtlr r12 - crclr cr0*4+so - blr - .cfi_endproc -V_FUNCTION_END(__kernel_get_tbfreq) Index: linux/arch/powerpc/kernel/vdso64/gettimeofday.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso64/gettimeofday.S +++ /dev/null @@ -1,255 +0,0 @@ -/* - * Userland implementation of gettimeofday() for 64 bits processes in a - * ppc64 kernel for use in the vDSO - * - * Copyright (C) 2004 Benjamin Herrenschmuidt (benh@kernel.crashing.org), - * IBM Corp. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ -#include -#include -#include -#include -#include - - .text -/* - * Exact prototype of gettimeofday - * - * int __kernel_gettimeofday(struct timeval *tv, struct timezone *tz); - * - */ -V_FUNCTION_BEGIN(__kernel_gettimeofday) - .cfi_startproc - mflr r12 - .cfi_register lr,r12 - - mr r11,r3 /* r11 holds tv */ - mr r10,r4 /* r10 holds tz */ - bl V_LOCAL_FUNC(__get_datapage) /* get data page */ - cmpldi r11,0 /* check if tv is NULL */ - beq 2f - bl V_LOCAL_FUNC(__do_get_xsec) /* get xsec from tb & kernel */ - lis r7,15 /* r7 = 1000000 = USEC_PER_SEC */ - ori r7,r7,16960 - rldicl r5,r4,44,20 /* r5 = sec = xsec / XSEC_PER_SEC */ - rldicr r6,r5,20,43 /* r6 = sec * XSEC_PER_SEC */ - std r5,TVAL64_TV_SEC(r11) /* store sec in tv */ - subf r0,r6,r4 /* r0 = xsec = (xsec - r6) */ - mulld r0,r0,r7 /* usec = (xsec * USEC_PER_SEC) / - * XSEC_PER_SEC - */ - rldicl r0,r0,44,20 - std r0,TVAL64_TV_USEC(r11) /* store usec in tv */ -2: cmpldi r10,0 /* check if tz is NULL */ - beq 1f - lwz r4,CFG_TZ_MINUTEWEST(r3)/* fill tz */ - lwz r5,CFG_TZ_DSTTIME(r3) - stw r4,TZONE_TZ_MINWEST(r10) - stw r5,TZONE_TZ_DSTTIME(r10) -1: mtlr r12 - crclr cr0*4+so - li r3,0 /* always success */ - blr - .cfi_endproc -V_FUNCTION_END(__kernel_gettimeofday) - - -/* - * Exact prototype of clock_gettime() - * - * int __kernel_clock_gettime(clockid_t clock_id, struct timespec *tp); - * - */ -V_FUNCTION_BEGIN(__kernel_clock_gettime) - .cfi_startproc - /* Check for supported clock IDs */ - cmpwi cr0,r3,CLOCK_REALTIME - cmpwi cr1,r3,CLOCK_MONOTONIC - cror cr0*4+eq,cr0*4+eq,cr1*4+eq - bne cr0,99f - - mflr r12 /* r12 saves lr */ - .cfi_register lr,r12 - mr r10,r3 /* r10 saves id */ - mr r11,r4 /* r11 saves tp */ - bl V_LOCAL_FUNC(__get_datapage) /* get data page */ - beq cr1,50f /* if monotonic -> jump there */ - - /* - * CLOCK_REALTIME - */ - - bl V_LOCAL_FUNC(__do_get_xsec) /* get xsec from tb & kernel */ - - lis r7,15 /* r7 = 1000000 = USEC_PER_SEC */ - ori r7,r7,16960 - rldicl r5,r4,44,20 /* r5 = sec = xsec / XSEC_PER_SEC */ - rldicr r6,r5,20,43 /* r6 = sec * XSEC_PER_SEC */ - std r5,TSPC64_TV_SEC(r11) /* store sec in tv */ - subf r0,r6,r4 /* r0 = xsec = (xsec - r6) */ - mulld r0,r0,r7 /* usec = (xsec * USEC_PER_SEC) / - * XSEC_PER_SEC - */ - rldicl r0,r0,44,20 - mulli r0,r0,1000 /* nsec = usec * 1000 */ - std r0,TSPC64_TV_NSEC(r11) /* store nsec in tp */ - - mtlr r12 - crclr cr0*4+so - li r3,0 - blr - - /* - * CLOCK_MONOTONIC - */ - -50: bl V_LOCAL_FUNC(__do_get_xsec) /* get xsec from tb & kernel */ - - lis r7,15 /* r7 = 1000000 = USEC_PER_SEC */ - ori r7,r7,16960 - rldicl r5,r4,44,20 /* r5 = sec = xsec / XSEC_PER_SEC */ - rldicr r6,r5,20,43 /* r6 = sec * XSEC_PER_SEC */ - subf r0,r6,r4 /* r0 = xsec = (xsec - r6) */ - mulld r0,r0,r7 /* usec = (xsec * USEC_PER_SEC) / - * XSEC_PER_SEC - */ - rldicl r6,r0,44,20 - mulli r6,r6,1000 /* nsec = usec * 1000 */ - - /* now we must fixup using wall to monotonic. We need to snapshot - * that value and do the counter trick again. Fortunately, we still - * have the counter value in r8 that was returned by __do_get_xsec. - * At this point, r5,r6 contain our sec/nsec values. - * can be used - */ - - lwa r4,WTOM_CLOCK_SEC(r3) - lwa r7,WTOM_CLOCK_NSEC(r3) - - /* We now have our result in r4,r7. We create a fake dependency - * on that result and re-check the counter - */ - or r9,r4,r7 - xor r0,r9,r9 - add r3,r3,r0 - ld r0,CFG_TB_UPDATE_COUNT(r3) - cmpld cr0,r0,r8 /* check if updated */ - bne- 50b - - /* Calculate and store result. Note that this mimmics the C code, - * which may cause funny results if nsec goes negative... is that - * possible at all ? - */ - add r4,r4,r5 - add r7,r7,r6 - lis r9,NSEC_PER_SEC@h - ori r9,r9,NSEC_PER_SEC@l - cmpl cr0,r7,r9 - cmpli cr1,r7,0 - blt 1f - subf r7,r9,r7 - addi r4,r4,1 -1: bge cr1,1f - addi r4,r4,-1 - add r7,r7,r9 -1: std r4,TSPC64_TV_SEC(r11) - std r7,TSPC64_TV_NSEC(r11) - - mtlr r12 - crclr cr0*4+so - li r3,0 - blr - - /* - * syscall fallback - */ -98: - mtlr r12 - mr r3,r10 - mr r4,r11 -99: - li r0,__NR_clock_gettime - sc - blr - .cfi_endproc -V_FUNCTION_END(__kernel_clock_gettime) - - -/* - * Exact prototype of clock_getres() - * - * int __kernel_clock_getres(clockid_t clock_id, struct timespec *res); - * - */ -V_FUNCTION_BEGIN(__kernel_clock_getres) - .cfi_startproc - /* Check for supported clock IDs */ - cmpwi cr0,r3,CLOCK_REALTIME - cmpwi cr1,r3,CLOCK_MONOTONIC - cror cr0*4+eq,cr0*4+eq,cr1*4+eq - bne cr0,99f - - li r3,0 - cmpli cr0,r4,0 - crclr cr0*4+so - beqlr - lis r5,CLOCK_REALTIME_RES@h - ori r5,r5,CLOCK_REALTIME_RES@l - std r3,TSPC64_TV_SEC(r4) - std r5,TSPC64_TV_NSEC(r4) - blr - - /* - * syscall fallback - */ -99: - li r0,__NR_clock_getres - sc - blr - .cfi_endproc -V_FUNCTION_END(__kernel_clock_getres) - - -/* - * This is the core of gettimeofday(), it returns the xsec - * value in r4 and expects the datapage ptr (non clobbered) - * in r3. clobbers r0,r4,r5,r6,r7,r8 - * When returning, r8 contains the counter value that can be reused - */ -V_FUNCTION_BEGIN(__do_get_xsec) - .cfi_startproc - /* check for update count & load values */ -1: ld r8,CFG_TB_UPDATE_COUNT(r3) - andi. r0,r8,1 /* pending update ? loop */ - bne- 1b - xor r0,r8,r8 /* create dependency */ - add r3,r3,r0 - - /* Get TB & offset it. We use the MFTB macro which will generate - * workaround code for Cell. - */ - MFTB(r7) - ld r9,CFG_TB_ORIG_STAMP(r3) - subf r7,r9,r7 - - /* Scale result */ - ld r5,CFG_TB_TO_XS(r3) - mulhdu r7,r7,r5 - - /* Add stamp since epoch */ - ld r6,CFG_STAMP_XSEC(r3) - add r4,r6,r7 - - xor r0,r4,r4 - add r3,r3,r0 - ld r0,CFG_TB_UPDATE_COUNT(r3) - cmpld cr0,r0,r8 /* check if updated */ - bne- 1b - blr - .cfi_endproc -V_FUNCTION_END(__do_get_xsec) Index: linux/arch/powerpc/kernel/vdso64/vdso64.lds.S =================================================================== --- linux.orig/arch/powerpc/kernel/vdso64/vdso64.lds.S +++ linux/arch/powerpc/kernel/vdso64/vdso64.lds.S @@ -115,10 +115,6 @@ VERSION global: __kernel_datapage_offset; /* Has to be there for the kernel to find */ __kernel_get_syscall_map; - __kernel_gettimeofday; - __kernel_clock_gettime; - __kernel_clock_getres; - __kernel_get_tbfreq; __kernel_sync_dicache; __kernel_sync_dicache_p5; __kernel_sigtramp_rt64; Index: linux/arch/powerpc/lib/locks.c =================================================================== --- linux.orig/arch/powerpc/lib/locks.c +++ linux/arch/powerpc/lib/locks.c @@ -25,7 +25,7 @@ #include #include -void __spin_yield(raw_spinlock_t *lock) +void __spin_yield(__raw_spinlock_t *lock) { unsigned int lock_value, holder_cpu, yield_count; @@ -82,7 +82,7 @@ void __rw_yield(raw_rwlock_t *rw) } #endif -void __raw_spin_unlock_wait(raw_spinlock_t *lock) +void __raw_spin_unlock_wait(__raw_spinlock_t *lock) { while (lock->slock) { HMT_low(); Index: linux/arch/powerpc/mm/fault.c =================================================================== --- linux.orig/arch/powerpc/mm/fault.c +++ linux/arch/powerpc/mm/fault.c @@ -138,8 +138,8 @@ static void do_dabr(struct pt_regs *regs * The return value is 0 if the fault was handled, or the signal * number if this is a kernel fault that can't be handled here. */ -int __kprobes do_page_fault(struct pt_regs *regs, unsigned long address, - unsigned long error_code) +int __kprobes notrace do_page_fault(struct pt_regs *regs, + unsigned long address, unsigned long error_code) { struct vm_area_struct * vma; struct mm_struct *mm = current->mm; @@ -184,7 +184,7 @@ int __kprobes do_page_fault(struct pt_re } #endif /* !(CONFIG_4xx || CONFIG_BOOKE)*/ - if (in_atomic() || mm == NULL) { + if (in_atomic() || mm == NULL || current->pagefault_disabled) { if (!user_mode(regs)) return SIGSEGV; /* in_atomic() in user mode is really bad, Index: linux/arch/powerpc/mm/hash_native_64.c =================================================================== --- linux.orig/arch/powerpc/mm/hash_native_64.c +++ linux/arch/powerpc/mm/hash_native_64.c @@ -36,7 +36,7 @@ #define HPTE_LOCK_BIT 3 -static DEFINE_SPINLOCK(native_tlbie_lock); +static DEFINE_RAW_SPINLOCK(native_tlbie_lock); static inline void __tlbie(unsigned long va, unsigned int psize) { Index: linux/arch/powerpc/mm/init_32.c =================================================================== --- linux.orig/arch/powerpc/mm/init_32.c +++ linux/arch/powerpc/mm/init_32.c @@ -56,7 +56,7 @@ #endif #define MAX_LOW_MEM CONFIG_LOWMEM_SIZE -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); unsigned long total_memory; unsigned long total_lowmem; Index: linux/arch/powerpc/mm/tlb_64.c =================================================================== --- linux.orig/arch/powerpc/mm/tlb_64.c +++ linux/arch/powerpc/mm/tlb_64.c @@ -31,13 +31,14 @@ #include #include #include +#include DEFINE_PER_CPU(struct ppc64_tlb_batch, ppc64_tlb_batch); /* This is declared as we are using the more or less generic * include/asm-powerpc/tlb.h file -- tgall */ -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); DEFINE_PER_CPU(struct pte_freelist_batch *, pte_freelist_cur); unsigned long pte_freelist_forced_free; @@ -94,8 +95,11 @@ static void pte_free_submit(struct pte_f void pgtable_free_tlb(struct mmu_gather *tlb, pgtable_free_t pgf) { - /* This is safe since tlb_gather_mmu has disabled preemption */ - cpumask_t local_cpumask = cpumask_of_cpu(smp_processor_id()); + /* + * This is safe since tlb_gather_mmu has disabled preemption. + * tlb->cpu is set by tlb_gather_mmu as well. + */ + cpumask_t local_cpumask = cpumask_of_cpu(tlb->cpu); struct pte_freelist_batch **batchp = &__get_cpu_var(pte_freelist_cur); if (atomic_read(&tlb->mm->mm_users) < 2 || @@ -201,6 +205,18 @@ void hpte_need_flush(struct mm_struct *m batch->pte[i] = rpte; batch->vaddr[i] = vaddr; batch->index = ++i; + +#ifdef CONFIG_PREEMPT_RT + /* + * Since flushing tlb needs expensive hypervisor call(s) on celleb, + * always flush it on RT to reduce scheduling latency. + */ + if (machine_is(celleb)) { + flush_tlb_pending(); + return; + } +#endif /* CONFIG_PREEMPT_RT */ + if (i >= PPC64_TLB_BATCH_NR) __flush_tlb_pending(batch); } Index: linux/arch/powerpc/platforms/cell/smp.c =================================================================== --- linux.orig/arch/powerpc/platforms/cell/smp.c +++ linux/arch/powerpc/platforms/cell/smp.c @@ -133,7 +133,7 @@ static void __devinit smp_iic_setup_cpu( iic_setup_cpu(); } -static DEFINE_SPINLOCK(timebase_lock); +static DEFINE_RAW_SPINLOCK(timebase_lock); static unsigned long timebase = 0; static void __devinit cell_give_timebase(void) Index: linux/arch/powerpc/platforms/celleb/htab.c =================================================================== --- linux.orig/arch/powerpc/platforms/celleb/htab.c +++ linux/arch/powerpc/platforms/celleb/htab.c @@ -40,7 +40,7 @@ #define DBG_LOW(fmt...) do { } while(0) #endif -static DEFINE_SPINLOCK(beat_htab_lock); +static DEFINE_RAW_SPINLOCK(beat_htab_lock); static inline unsigned int beat_read_mask(unsigned hpte_group) { Index: linux/arch/powerpc/platforms/celleb/interrupt.c =================================================================== --- linux.orig/arch/powerpc/platforms/celleb/interrupt.c +++ linux/arch/powerpc/platforms/celleb/interrupt.c @@ -29,8 +29,12 @@ #include "interrupt.h" #include "beat_wrapper.h" +#ifdef CONFIG_PREEMPT_HARDIRQS +extern int hardirq_preemption; +#endif /* CONFIG_PREEMPT_HARDIRQS */ + #define MAX_IRQS NR_IRQS -static DEFINE_SPINLOCK(beatic_irq_mask_lock); +static DEFINE_RAW_SPINLOCK(beatic_irq_mask_lock); static uint64_t beatic_irq_mask_enable[(MAX_IRQS+255)/64]; static uint64_t beatic_irq_mask_ack[(MAX_IRQS+255)/64]; @@ -71,12 +75,35 @@ static void beatic_mask_irq(unsigned int spin_unlock_irqrestore(&beatic_irq_mask_lock, flags); } +static void __beatic_eoi_irq(unsigned int irq_plug) +{ + s64 err; + + if ((err = beat_downcount_of_interrupt(irq_plug)) != 0) { + if ((err & 0xFFFFFFFF) != 0xFFFFFFF5) /* -11: wrong state */ + panic("Failed to downcount IRQ! Error = %16lx", err); + + printk(KERN_ERR "IRQ over-downcounted, plug %d\n", irq_plug); + } +} + static void beatic_unmask_irq(unsigned int irq_plug) { unsigned long flags; +#ifdef CONFIG_PREEMPT_HARDIRQS + if (hardirq_preemption) + __beatic_eoi_irq(irq_plug); +#endif /* CONFIG_PREEMPT_HARDIRQS */ + spin_lock_irqsave(&beatic_irq_mask_lock, flags); beatic_irq_mask_enable[irq_plug/64] |= 1UL << (63 - (irq_plug%64)); + +#ifdef CONFIG_PREEMPT_HARDIRQS + if (hardirq_preemption) + beatic_irq_mask_ack[irq_plug/64] |= 1UL << (63 - (irq_plug%64)); +#endif /* CONFIG_PREEMPT_HARDIRQS */ + beatic_update_irq_mask(irq_plug); spin_unlock_irqrestore(&beatic_irq_mask_lock, flags); } @@ -93,15 +120,15 @@ static void beatic_ack_irq(unsigned int static void beatic_end_irq(unsigned int irq_plug) { - s64 err; unsigned long flags; - if ((err = beat_downcount_of_interrupt(irq_plug)) != 0) { - if ((err & 0xFFFFFFFF) != 0xFFFFFFF5) /* -11: wrong state */ - panic("Failed to downcount IRQ! Error = %16lx", err); +#ifdef CONFIG_PREEMPT_HARDIRQS + if (hardirq_preemption) + return; +#endif /* CONFIG_PREEMPT_HARDIRQS */ + + __beatic_eoi_irq(irq_plug); - printk(KERN_ERR "IRQ over-downcounted, plug %d\n", irq_plug); - } spin_lock_irqsave(&beatic_irq_mask_lock, flags); beatic_irq_mask_ack[irq_plug/64] |= 1UL << (63 - (irq_plug%64)); beatic_update_irq_mask(irq_plug); Index: linux/arch/powerpc/platforms/chrp/smp.c =================================================================== --- linux.orig/arch/powerpc/platforms/chrp/smp.c +++ linux/arch/powerpc/platforms/chrp/smp.c @@ -44,7 +44,7 @@ static void __devinit smp_chrp_setup_cpu mpic_setup_this_cpu(); } -static DEFINE_SPINLOCK(timebase_lock); +static DEFINE_RAW_SPINLOCK(timebase_lock); static unsigned int timebase_upper = 0, timebase_lower = 0; void __devinit smp_chrp_give_timebase(void) Index: linux/arch/powerpc/platforms/chrp/time.c =================================================================== --- linux.orig/arch/powerpc/platforms/chrp/time.c +++ linux/arch/powerpc/platforms/chrp/time.c @@ -27,7 +27,7 @@ #include #include -extern spinlock_t rtc_lock; +extern raw_spinlock_t rtc_lock; static int nvram_as1 = NVRAM_AS1; static int nvram_as0 = NVRAM_AS0; Index: linux/arch/powerpc/platforms/iseries/setup.c =================================================================== --- linux.orig/arch/powerpc/platforms/iseries/setup.c +++ linux/arch/powerpc/platforms/iseries/setup.c @@ -564,12 +564,14 @@ static void yield_shared_processor(void) static void iseries_shared_idle(void) { while (1) { - while (!need_resched() && !hvlpevent_is_pending()) { + while (!need_resched() && !need_resched_delayed() + && !hvlpevent_is_pending()) { local_irq_disable(); ppc64_runlatch_off(); /* Recheck with irqs off */ - if (!need_resched() && !hvlpevent_is_pending()) + if (!need_resched() && !need_resched_delayed() + && !hvlpevent_is_pending()) yield_shared_processor(); HMT_medium(); Index: linux/arch/powerpc/platforms/powermac/feature.c =================================================================== --- linux.orig/arch/powerpc/platforms/powermac/feature.c +++ linux/arch/powerpc/platforms/powermac/feature.c @@ -59,7 +59,7 @@ extern struct device_node *k2_skiplist[2 * We use a single global lock to protect accesses. Each driver has * to take care of its own locking */ -DEFINE_SPINLOCK(feature_lock); +DEFINE_RAW_SPINLOCK(feature_lock); #define LOCK(flags) spin_lock_irqsave(&feature_lock, flags); #define UNLOCK(flags) spin_unlock_irqrestore(&feature_lock, flags); Index: linux/arch/powerpc/platforms/powermac/nvram.c =================================================================== --- linux.orig/arch/powerpc/platforms/powermac/nvram.c +++ linux/arch/powerpc/platforms/powermac/nvram.c @@ -80,7 +80,7 @@ static int is_core_99; static int core99_bank = 0; static int nvram_partitions[3]; // XXX Turn that into a sem -static DEFINE_SPINLOCK(nv_lock); +static DEFINE_RAW_SPINLOCK(nv_lock); static int (*core99_write_bank)(int bank, u8* datas); static int (*core99_erase_bank)(int bank); Index: linux/arch/powerpc/platforms/powermac/pic.c =================================================================== --- linux.orig/arch/powerpc/platforms/powermac/pic.c +++ linux/arch/powerpc/platforms/powermac/pic.c @@ -63,7 +63,7 @@ static int max_irqs; static int max_real_irqs; static u32 level_mask[4]; -static DEFINE_SPINLOCK(pmac_pic_lock); +static DEFINE_RAW_SPINLOCK(pmac_pic_lock); #define NR_MASK_WORDS ((NR_IRQS + 31) / 32) static unsigned long ppc_lost_interrupts[NR_MASK_WORDS]; Index: linux/arch/powerpc/platforms/pseries/setup.c =================================================================== --- linux.orig/arch/powerpc/platforms/pseries/setup.c +++ linux/arch/powerpc/platforms/pseries/setup.c @@ -412,7 +412,8 @@ static void pseries_dedicated_idle_sleep set_thread_flag(TIF_POLLING_NRFLAG); while (get_tb() < start_snooze) { - if (need_resched() || cpu_is_offline(cpu)) + if (need_resched() || need_resched_delayed() || + cpu_is_offline(cpu)) goto out; ppc64_runlatch_off(); HMT_low(); @@ -423,7 +424,8 @@ static void pseries_dedicated_idle_sleep clear_thread_flag(TIF_POLLING_NRFLAG); smp_mb(); local_irq_disable(); - if (need_resched() || cpu_is_offline(cpu)) + if (need_resched() || need_resched_delayed() || + cpu_is_offline(cpu)) goto out; } Index: linux/arch/powerpc/platforms/pseries/smp.c =================================================================== --- linux.orig/arch/powerpc/platforms/pseries/smp.c +++ linux/arch/powerpc/platforms/pseries/smp.c @@ -154,7 +154,7 @@ static void __devinit smp_xics_setup_cpu } #endif /* CONFIG_XICS */ -static DEFINE_SPINLOCK(timebase_lock); +static DEFINE_RAW_SPINLOCK(timebase_lock); static unsigned long timebase = 0; static void __devinit pSeries_give_timebase(void) Index: linux/arch/powerpc/sysdev/i8259.c =================================================================== --- linux.orig/arch/powerpc/sysdev/i8259.c +++ linux/arch/powerpc/sysdev/i8259.c @@ -23,7 +23,7 @@ static unsigned char cached_8259[2] = { #define cached_A1 (cached_8259[0]) #define cached_21 (cached_8259[1]) -static DEFINE_SPINLOCK(i8259_lock); +static DEFINE_RAW_SPINLOCK(i8259_lock); static struct device_node *i8259_node; static struct irq_host *i8259_host; Index: linux/arch/powerpc/sysdev/ipic.c =================================================================== --- linux.orig/arch/powerpc/sysdev/ipic.c +++ linux/arch/powerpc/sysdev/ipic.c @@ -30,7 +30,7 @@ #include "ipic.h" static struct ipic * primary_ipic; -static DEFINE_SPINLOCK(ipic_lock); +static DEFINE_RAW_SPINLOCK(ipic_lock); static struct ipic_info ipic_info[] = { [9] = { Index: linux/arch/powerpc/sysdev/mpic.c =================================================================== --- linux.orig/arch/powerpc/sysdev/mpic.c +++ linux/arch/powerpc/sysdev/mpic.c @@ -46,7 +46,7 @@ static struct mpic *mpics; static struct mpic *mpic_primary; -static DEFINE_SPINLOCK(mpic_lock); +static DEFINE_RAW_SPINLOCK(mpic_lock); #ifdef CONFIG_PPC32 /* XXX for now */ #ifdef CONFIG_IRQ_ALL_CPUS Index: linux/arch/powerpc/xmon/xmon.c =================================================================== --- linux.orig/arch/powerpc/xmon/xmon.c +++ linux/arch/powerpc/xmon/xmon.c @@ -340,6 +340,7 @@ static int xmon_core(struct pt_regs *reg unsigned long timeout; #endif + preempt_disable(); local_irq_save(flags); bp = in_breakpoint_table(regs->nip, &offset); @@ -516,6 +517,7 @@ static int xmon_core(struct pt_regs *reg insert_cpu_bpts(); local_irq_restore(flags); + preempt_enable(); return cmd != 'X' && cmd != EOF; } @@ -2129,7 +2131,7 @@ print_address(unsigned long addr) static unsigned long mdest; /* destination address */ static unsigned long msrc; /* source address */ static unsigned long mval; /* byte value to set memory to */ -static unsigned long mcount; /* # bytes to affect */ +static unsigned long xmon_mcount; /* # bytes to affect */ static unsigned long mdiffs; /* max # differences to print */ void @@ -2141,19 +2143,20 @@ memops(int cmd) scanhex((void *)(cmd == 's'? &mval: &msrc)); if( termch != '\n' ) termch = 0; - scanhex((void *)&mcount); + scanhex((void *)&xmon_mcount); switch( cmd ){ case 'm': - memmove((void *)mdest, (void *)msrc, mcount); + memmove((void *)mdest, (void *)msrc, xmon_mcount); break; case 's': - memset((void *)mdest, mval, mcount); + memset((void *)mdest, mval, xmon_mcount); break; case 'd': if( termch != '\n' ) termch = 0; scanhex((void *)&mdiffs); - memdiffs((unsigned char *)mdest, (unsigned char *)msrc, mcount, mdiffs); + memdiffs((unsigned char *)mdest, (unsigned char *)msrc, + xmon_mcount, mdiffs); break; } } Index: linux/arch/ppc/8260_io/enet.c =================================================================== --- linux.orig/arch/ppc/8260_io/enet.c +++ linux/arch/ppc/8260_io/enet.c @@ -115,7 +115,7 @@ struct scc_enet_private { scc_t *sccp; struct net_device_stats stats; uint tx_full; - spinlock_t lock; + raw_spinlock_t lock; }; static int scc_enet_open(struct net_device *dev); Index: linux/arch/ppc/8260_io/fcc_enet.c =================================================================== --- linux.orig/arch/ppc/8260_io/fcc_enet.c +++ linux/arch/ppc/8260_io/fcc_enet.c @@ -375,7 +375,7 @@ struct fcc_enet_private { volatile fcc_enet_t *ep; struct net_device_stats stats; uint tx_free; - spinlock_t lock; + raw_spinlock_t lock; #ifdef CONFIG_USE_MDIO uint phy_id; Index: linux/arch/ppc/8xx_io/commproc.c =================================================================== --- linux.orig/arch/ppc/8xx_io/commproc.c +++ linux/arch/ppc/8xx_io/commproc.c @@ -370,7 +370,7 @@ cpm_setbrg(uint brg, uint rate) /* * dpalloc / dpfree bits. */ -static spinlock_t cpm_dpmem_lock; +static raw_spinlock_t cpm_dpmem_lock; /* * 16 blocks should be enough to satisfy all requests * until the memory subsystem goes up... Index: linux/arch/ppc/8xx_io/enet.c =================================================================== --- linux.orig/arch/ppc/8xx_io/enet.c +++ linux/arch/ppc/8xx_io/enet.c @@ -142,7 +142,7 @@ struct scc_enet_private { unsigned char *rx_vaddr[RX_RING_SIZE]; struct net_device_stats stats; uint tx_full; - spinlock_t lock; + raw_spinlock_t lock; }; static int scc_enet_open(struct net_device *dev); Index: linux/arch/ppc/8xx_io/fec.c =================================================================== --- linux.orig/arch/ppc/8xx_io/fec.c +++ linux/arch/ppc/8xx_io/fec.c @@ -164,7 +164,7 @@ struct fec_enet_private { struct net_device_stats stats; uint tx_full; - spinlock_t lock; + raw_spinlock_t lock; #ifdef CONFIG_USE_MDIO uint phy_id; Index: linux/arch/ppc/Kconfig =================================================================== --- linux.orig/arch/ppc/Kconfig +++ linux/arch/ppc/Kconfig @@ -12,13 +12,6 @@ config GENERIC_HARDIRQS bool default y -config RWSEM_GENERIC_SPINLOCK - bool - -config RWSEM_XCHGADD_ALGORITHM - bool - default y - config ARCH_HAS_ILOG2_U32 bool default y @@ -988,6 +981,18 @@ config ARCH_POPULATES_NODE_MAP source kernel/Kconfig.hz source kernel/Kconfig.preempt + +config RWSEM_GENERIC_SPINLOCK + bool + default y + +config ASM_SEMAPHORES + bool + default y + +config RWSEM_XCHGADD_ALGORITHM + bool + source "mm/Kconfig" source "fs/Kconfig.binfmt" Index: linux/arch/ppc/boot/Makefile =================================================================== --- linux.orig/arch/ppc/boot/Makefile +++ linux/arch/ppc/boot/Makefile @@ -14,6 +14,15 @@ # CFLAGS += -fno-builtin -D__BOOTER__ -Iarch/$(ARCH)/boot/include + +ifdef CONFIG_MCOUNT +# do not trace the boot loader +nullstring := +space := $(nullstring) # end of the line +pg_flag = $(nullstring) -pg # end of the line +CFLAGS := $(subst ${pg_flag},${space},${CFLAGS}) +endif + HOSTCFLAGS += -Iarch/$(ARCH)/boot/include BOOT_TARGETS = zImage zImage.initrd znetboot znetboot.initrd Index: linux/arch/ppc/kernel/entry.S =================================================================== --- linux.orig/arch/ppc/kernel/entry.S +++ linux/arch/ppc/kernel/entry.S @@ -863,7 +863,7 @@ global_dbcr0: #endif /* !(CONFIG_4xx || CONFIG_BOOKE) */ do_work: /* r10 contains MSR_KERNEL here */ - andi. r0,r9,_TIF_NEED_RESCHED + andi. r0,r9,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) beq do_user_signal do_resched: /* r10 contains MSR_KERNEL here */ @@ -877,7 +877,7 @@ recheck: MTMSRD(r10) /* disable interrupts */ rlwinm r9,r1,0,0,18 lwz r9,TI_FLAGS(r9) - andi. r0,r9,_TIF_NEED_RESCHED + andi. r0,r9,(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED) bne- do_resched andi. r0,r9,_TIF_SIGPENDING beq restore_user Index: linux/arch/ppc/kernel/semaphore.c =================================================================== --- linux.orig/arch/ppc/kernel/semaphore.c +++ linux/arch/ppc/kernel/semaphore.c @@ -29,7 +29,7 @@ * sem->count = tmp; * return old_count; */ -static inline int __sem_update_count(struct semaphore *sem, int incr) +static inline int __sem_update_count(struct compat_semaphore *sem, int incr) { int old_count, tmp; @@ -48,7 +48,7 @@ static inline int __sem_update_count(str return old_count; } -void __up(struct semaphore *sem) +void __compat_up(struct compat_semaphore *sem) { /* * Note that we incremented count in up() before we came here, @@ -70,7 +70,7 @@ void __up(struct semaphore *sem) * Thus it is only when we decrement count from some value > 0 * that we have actually got the semaphore. */ -void __sched __down(struct semaphore *sem) +void __sched __compat_down(struct compat_semaphore *sem) { struct task_struct *tsk = current; DECLARE_WAITQUEUE(wait, tsk); @@ -100,7 +100,7 @@ void __sched __down(struct semaphore *se wake_up(&sem->wait); } -int __sched __down_interruptible(struct semaphore * sem) +int __sched __compat_down_interruptible(struct compat_semaphore * sem) { int retval = 0; struct task_struct *tsk = current; @@ -129,3 +129,8 @@ int __sched __down_interruptible(struct wake_up(&sem->wait); return retval; } + +int compat_sem_is_locked(struct compat_semaphore *sem) +{ + return (int) atomic_read(&sem->count) < 0; +} Index: linux/arch/ppc/kernel/smp.c =================================================================== --- linux.orig/arch/ppc/kernel/smp.c +++ linux/arch/ppc/kernel/smp.c @@ -136,6 +136,16 @@ void smp_send_reschedule(int cpu) smp_message_pass(cpu, PPC_MSG_RESCHEDULE); } +/* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them: + */ +void smp_send_reschedule_allbutself(void) +{ + smp_message_pass(MSG_ALL_BUT_SELF, PPC_MSG_RESCHEDULE, 0, 0); +} + #ifdef CONFIG_XMON void smp_send_xmon_break(int cpu) { @@ -160,7 +170,7 @@ void smp_send_stop(void) * static memory requirements. It also looks cleaner. * Stolen from the i386 version. */ -static DEFINE_SPINLOCK(call_lock); +static DEFINE_RAW_SPINLOCK(call_lock); static struct call_data_struct { void (*func) (void *info); Index: linux/arch/ppc/kernel/time.c =================================================================== --- linux.orig/arch/ppc/kernel/time.c +++ linux/arch/ppc/kernel/time.c @@ -102,7 +102,7 @@ static inline int tb_delta(unsigned *jif } #ifdef CONFIG_SMP -unsigned long profile_pc(struct pt_regs *regs) +unsigned long notrace profile_pc(struct pt_regs *regs) { unsigned long pc = instruction_pointer(regs); Index: linux/arch/ppc/kernel/traps.c =================================================================== --- linux.orig/arch/ppc/kernel/traps.c +++ linux/arch/ppc/kernel/traps.c @@ -72,7 +72,7 @@ void (*debugger_fault_handler)(struct pt * Trap & Exception support */ -DEFINE_SPINLOCK(die_lock); +DEFINE_RAW_SPINLOCK(die_lock); int die(const char * str, struct pt_regs * fp, long err) { @@ -107,6 +107,10 @@ void _exception(int signr, struct pt_reg debugger(regs); die("Exception in kernel mode", regs, signr); } +#ifdef CONFIG_PREEMPT_RT + local_irq_enable(); + preempt_check_resched(); +#endif info.si_signo = signr; info.si_errno = 0; info.si_code = code; Index: linux/arch/ppc/lib/locks.c =================================================================== --- linux.orig/arch/ppc/lib/locks.c +++ linux/arch/ppc/lib/locks.c @@ -42,7 +42,7 @@ static inline unsigned long __spin_trylo return ret; } -void _raw_spin_lock(spinlock_t *lock) +void __raw_spin_lock(raw_spinlock_t *lock) { int cpu = smp_processor_id(); unsigned int stuck = INIT_STUCK; @@ -62,9 +62,9 @@ void _raw_spin_lock(spinlock_t *lock) lock->owner_pc = (unsigned long)__builtin_return_address(0); lock->owner_cpu = cpu; } -EXPORT_SYMBOL(_raw_spin_lock); +EXPORT_SYMBOL(__raw_spin_lock); -int _raw_spin_trylock(spinlock_t *lock) +int __raw_spin_trylock(raw_spinlock_t *lock) { if (__spin_trylock(&lock->lock)) return 0; @@ -72,9 +72,9 @@ int _raw_spin_trylock(spinlock_t *lock) lock->owner_pc = (unsigned long)__builtin_return_address(0); return 1; } -EXPORT_SYMBOL(_raw_spin_trylock); +EXPORT_SYMBOL(__raw_spin_trylock); -void _raw_spin_unlock(spinlock_t *lp) +void __raw_spin_unlock(raw_spinlock_t *lp) { if ( !lp->lock ) printk("_spin_unlock(%p): no lock cpu %d curr PC %p %s/%d\n", @@ -88,13 +88,13 @@ void _raw_spin_unlock(spinlock_t *lp) wmb(); lp->lock = 0; } -EXPORT_SYMBOL(_raw_spin_unlock); +EXPORT_SYMBOL(__raw_spin_unlock); /* * For rwlocks, zero is unlocked, -1 is write-locked, * positive is read-locked. */ -static __inline__ int __read_trylock(rwlock_t *rw) +static __inline__ int __read_trylock(raw_rwlock_t *rw) { signed int tmp; @@ -114,13 +114,13 @@ static __inline__ int __read_trylock(rwl return tmp; } -int _raw_read_trylock(rwlock_t *rw) +int __raw_read_trylock(raw_rwlock_t *rw) { return __read_trylock(rw) > 0; } -EXPORT_SYMBOL(_raw_read_trylock); +EXPORT_SYMBOL(__raw_read_trylock); -void _raw_read_lock(rwlock_t *rw) +void __raw_read_lock(rwlock_t *rw) { unsigned int stuck; @@ -135,9 +135,9 @@ void _raw_read_lock(rwlock_t *rw) } } } -EXPORT_SYMBOL(_raw_read_lock); +EXPORT_SYMBOL(__raw_read_lock); -void _raw_read_unlock(rwlock_t *rw) +void __raw_read_unlock(raw_rwlock_t *rw) { if ( rw->lock == 0 ) printk("_read_unlock(): %s/%d (nip %08lX) lock %d\n", @@ -146,9 +146,9 @@ void _raw_read_unlock(rwlock_t *rw) wmb(); atomic_dec((atomic_t *) &(rw)->lock); } -EXPORT_SYMBOL(_raw_read_unlock); +EXPORT_SYMBOL(__raw_read_unlock); -void _raw_write_lock(rwlock_t *rw) +void __raw_write_lock(raw_rwlock_t *rw) { unsigned int stuck; @@ -164,18 +164,18 @@ void _raw_write_lock(rwlock_t *rw) } wmb(); } -EXPORT_SYMBOL(_raw_write_lock); +EXPORT_SYMBOL(__raw_write_lock); -int _raw_write_trylock(rwlock_t *rw) +int __raw_write_trylock(raw_rwlock_t *rw) { if (cmpxchg(&rw->lock, 0, -1) != 0) return 0; wmb(); return 1; } -EXPORT_SYMBOL(_raw_write_trylock); +EXPORT_SYMBOL(__raw_write_trylock); -void _raw_write_unlock(rwlock_t *rw) +void __raw_write_unlock(raw_rwlock_t *rw) { if (rw->lock >= 0) printk("_write_lock(): %s/%d (nip %08lX) lock %d\n", @@ -184,6 +184,6 @@ void _raw_write_unlock(rwlock_t *rw) wmb(); rw->lock = 0; } -EXPORT_SYMBOL(_raw_write_unlock); +EXPORT_SYMBOL(__raw_write_unlock); #endif Index: linux/arch/ppc/mm/fault.c =================================================================== --- linux.orig/arch/ppc/mm/fault.c +++ linux/arch/ppc/mm/fault.c @@ -89,7 +89,7 @@ static int store_updates_sp(struct pt_re * the error_code parameter is ESR for a data fault, 0 for an instruction * fault. */ -int do_page_fault(struct pt_regs *regs, unsigned long address, +int notrace do_page_fault(struct pt_regs *regs, unsigned long address, unsigned long error_code) { struct vm_area_struct * vma; Index: linux/arch/ppc/mm/init.c =================================================================== --- linux.orig/arch/ppc/mm/init.c +++ linux/arch/ppc/mm/init.c @@ -55,7 +55,7 @@ #endif #define MAX_LOW_MEM CONFIG_LOWMEM_SIZE -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); unsigned long total_memory; unsigned long total_lowmem; Index: linux/arch/ppc/platforms/hdpu.c =================================================================== --- linux.orig/arch/ppc/platforms/hdpu.c +++ linux/arch/ppc/platforms/hdpu.c @@ -55,7 +55,7 @@ static void parse_bootinfo(unsigned long static void hdpu_set_l1pe(void); static void hdpu_cpustate_set(unsigned char new_state); #ifdef CONFIG_SMP -static DEFINE_SPINLOCK(timebase_lock); +static DEFINE_RAW_SPINLOCK(timebase_lock); static unsigned int timebase_upper = 0, timebase_lower = 0; extern int smp_tb_synchronized; Index: linux/arch/ppc/platforms/sbc82xx.c =================================================================== --- linux.orig/arch/ppc/platforms/sbc82xx.c +++ linux/arch/ppc/platforms/sbc82xx.c @@ -65,7 +65,7 @@ static void sbc82xx_time_init(void) static volatile char *sbc82xx_i8259_map; static char sbc82xx_i8259_mask = 0xff; -static DEFINE_SPINLOCK(sbc82xx_i8259_lock); +static DEFINE_RAW_SPINLOCK(sbc82xx_i8259_lock); static void sbc82xx_i8259_mask_and_ack_irq(unsigned int irq_nr) { Index: linux/arch/ppc/syslib/cpm2_common.c =================================================================== --- linux.orig/arch/ppc/syslib/cpm2_common.c +++ linux/arch/ppc/syslib/cpm2_common.c @@ -114,7 +114,7 @@ cpm2_fastbrg(uint brg, uint rate, int di /* * dpalloc / dpfree bits. */ -static spinlock_t cpm_dpmem_lock; +static raw_spinlock_t cpm_dpmem_lock; /* 16 blocks should be enough to satisfy all requests * until the memory subsystem goes up... */ static rh_block_t cpm_boot_dpmem_rh_block[16]; Index: linux/arch/ppc/syslib/ocp.c =================================================================== --- linux.orig/arch/ppc/syslib/ocp.c +++ linux/arch/ppc/syslib/ocp.c @@ -44,11 +44,11 @@ #include #include #include +#include #include #include #include -#include #include //#define DBG(x) printk x Index: linux/arch/ppc/syslib/open_pic.c =================================================================== --- linux.orig/arch/ppc/syslib/open_pic.c +++ linux/arch/ppc/syslib/open_pic.c @@ -526,7 +526,7 @@ void openpic_reset_processor_phys(u_int } #if defined(CONFIG_SMP) || defined(CONFIG_PM) -static DEFINE_SPINLOCK(openpic_setup_lock); +static DEFINE_RAW_SPINLOCK(openpic_setup_lock); #endif #ifdef CONFIG_SMP Index: linux/arch/ppc/syslib/open_pic2.c =================================================================== --- linux.orig/arch/ppc/syslib/open_pic2.c +++ linux/arch/ppc/syslib/open_pic2.c @@ -380,7 +380,7 @@ static void openpic2_set_spurious(u_int vec); } -static DEFINE_SPINLOCK(openpic2_setup_lock); +static DEFINE_RAW_SPINLOCK(openpic2_setup_lock); /* * Initialize a timer interrupt (and disable it) Index: linux/arch/sh/kernel/cpu/clock.c =================================================================== --- linux.orig/arch/sh/kernel/cpu/clock.c +++ linux/arch/sh/kernel/cpu/clock.c @@ -28,7 +28,7 @@ #include static LIST_HEAD(clock_list); -static DEFINE_SPINLOCK(clock_lock); +static DEFINE_RAW_SPINLOCK(clock_lock); static DEFINE_MUTEX(clock_list_sem); /* Index: linux/arch/sh/kernel/cpu/sh4/sq.c =================================================================== --- linux.orig/arch/sh/kernel/cpu/sh4/sq.c +++ linux/arch/sh/kernel/cpu/sh4/sq.c @@ -37,7 +37,7 @@ struct sq_mapping { }; static struct sq_mapping *sq_mapping_list; -static DEFINE_SPINLOCK(sq_mapping_lock); +static DEFINE_RAW_SPINLOCK(sq_mapping_lock); static struct kmem_cache *sq_cache; static unsigned long *sq_bitmap; Index: linux/arch/sh/kernel/entry-common.S =================================================================== --- linux.orig/arch/sh/kernel/entry-common.S +++ linux/arch/sh/kernel/entry-common.S @@ -157,7 +157,7 @@ ENTRY(resume_userspace) mov.l @(TI_FLAGS,r8), r0 ! current_thread_info->flags tst #_TIF_WORK_MASK, r0 bt/s __restore_all - tst #_TIF_NEED_RESCHED, r0 + tst #_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED, r0 .align 2 work_pending: @@ -209,10 +209,10 @@ work_resched: tst #_TIF_WORK_MASK, r0 bt __restore_all bra work_pending - tst #_TIF_NEED_RESCHED, r0 + tst #_TIF_NEED_RESCHED | _TIF_NEED_RESCHED_DELAYED, r0 .align 2 -1: .long schedule +1: .long __schedule 2: .long do_notify_resume 3: .long restore_all #ifdef CONFIG_TRACE_IRQFLAGS @@ -226,7 +226,7 @@ syscall_exit_work: ! r8: current_thread_info tst #_TIF_SYSCALL_TRACE | _TIF_SINGLESTEP, r0 bt/s work_pending - tst #_TIF_NEED_RESCHED, r0 + tst #_TIF_NEED_RESCHED| _TIF_NEED_RESCHED_DELAYED, r0 #ifdef CONFIG_TRACE_IRQFLAGS mov.l 5f, r0 jsr @r0 Index: linux/arch/sh/kernel/irq.c =================================================================== --- linux.orig/arch/sh/kernel/irq.c +++ linux/arch/sh/kernel/irq.c @@ -82,7 +82,7 @@ static union irq_ctx *hardirq_ctx[NR_CPU static union irq_ctx *softirq_ctx[NR_CPUS] __read_mostly; #endif -asmlinkage int do_IRQ(unsigned int irq, struct pt_regs *regs) +asmlinkage notrace int do_IRQ(unsigned int irq, struct pt_regs *regs) { struct pt_regs *old_regs = set_irq_regs(regs); #ifdef CONFIG_4KSTACKS Index: linux/arch/sh/kernel/process.c =================================================================== --- linux.orig/arch/sh/kernel/process.c +++ linux/arch/sh/kernel/process.c @@ -62,7 +62,7 @@ void default_idle(void) clear_thread_flag(TIF_POLLING_NRFLAG); smp_mb__after_clear_bit(); set_bl_bit(); - while (!need_resched()) + while (!need_resched() && !need_resched_delayed()) cpu_sleep(); clear_bl_bit(); set_thread_flag(TIF_POLLING_NRFLAG); @@ -83,13 +83,15 @@ void cpu_idle(void) idle = default_idle; tick_nohz_stop_sched_tick(); - while (!need_resched()) + while (!need_resched() && !need_resched_delayed()) idle(); tick_nohz_restart_sched_tick(); - preempt_enable_no_resched(); - schedule(); + local_irq_disable(); + __preempt_enable_no_resched(); + __schedule(); preempt_disable(); + local_irq_enable(); check_pgt_cache(); } } Index: linux/arch/sh/kernel/semaphore.c =================================================================== --- linux.orig/arch/sh/kernel/semaphore.c +++ linux/arch/sh/kernel/semaphore.c @@ -46,7 +46,7 @@ DEFINE_SPINLOCK(semaphore_wake_lock); * critical part is the inline stuff in * where we want to avoid any extra jumps and calls. */ -void __up(struct semaphore *sem) +void __attribute_used__ __compat_up(struct compat_semaphore *sem) { wake_one_more(sem); wake_up(&sem->wait); @@ -104,7 +104,7 @@ void __up(struct semaphore *sem) tsk->state = TASK_RUNNING; \ remove_wait_queue(&sem->wait, &wait); -void __sched __down(struct semaphore * sem) +void __attribute_used__ __sched __compat_down(struct compat_semaphore * sem) { DOWN_VAR DOWN_HEAD(TASK_UNINTERRUPTIBLE) @@ -114,7 +114,7 @@ void __sched __down(struct semaphore * s DOWN_TAIL(TASK_UNINTERRUPTIBLE) } -int __sched __down_interruptible(struct semaphore * sem) +int __attribute_used__ __sched __compat_down_interruptible(struct compat_semaphore * sem) { int ret = 0; DOWN_VAR @@ -133,7 +133,13 @@ int __sched __down_interruptible(struct return ret; } -int __down_trylock(struct semaphore * sem) +int __attribute_used__ __compat_down_trylock(struct compat_semaphore * sem) { return waking_non_zero_trylock(sem); } + +fastcall int __sched compat_sem_is_locked(struct compat_semaphore *sem) +{ + return (int) atomic_read(&sem->count) < 0; +} + Index: linux/arch/sh/kernel/sh_ksyms.c =================================================================== --- linux.orig/arch/sh/kernel/sh_ksyms.c +++ linux/arch/sh/kernel/sh_ksyms.c @@ -26,7 +26,6 @@ EXPORT_SYMBOL(sh_mv); /* platform dependent support */ EXPORT_SYMBOL(dump_fpu); EXPORT_SYMBOL(kernel_thread); -EXPORT_SYMBOL(irq_desc); EXPORT_SYMBOL(no_irq_type); EXPORT_SYMBOL(strlen); @@ -50,9 +49,9 @@ EXPORT_SYMBOL(get_vm_area); #endif /* semaphore exports */ -EXPORT_SYMBOL(__up); -EXPORT_SYMBOL(__down); -EXPORT_SYMBOL(__down_interruptible); +EXPORT_SYMBOL(__compat_up); +EXPORT_SYMBOL(__compat_down); +EXPORT_SYMBOL(__compat_down_interruptible); EXPORT_SYMBOL(__udelay); EXPORT_SYMBOL(__ndelay); @@ -98,7 +97,7 @@ EXPORT_SYMBOL(__flush_purge_region); EXPORT_SYMBOL(clear_user_page); #endif -EXPORT_SYMBOL(__down_trylock); +EXPORT_SYMBOL(__compat_down_trylock); #ifdef CONFIG_SMP EXPORT_SYMBOL(synchronize_irq); Index: linux/arch/sh/kernel/signal.c =================================================================== --- linux.orig/arch/sh/kernel/signal.c +++ linux/arch/sh/kernel/signal.c @@ -565,6 +565,13 @@ static void do_signal(struct pt_regs *re struct k_sigaction ka; sigset_t *oldset; +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + raw_local_irq_enable(); + preempt_check_resched(); +#endif /* * We want the common case to go fast, which * is why we may in certain cases get here from Index: linux/arch/sh/kernel/time.c =================================================================== --- linux.orig/arch/sh/kernel/time.c +++ linux/arch/sh/kernel/time.c @@ -24,7 +24,7 @@ struct sys_timer *sys_timer; /* Move this somewhere more sensible.. */ -DEFINE_SPINLOCK(rtc_lock); +DEFINE_RAW_SPINLOCK(rtc_lock); EXPORT_SYMBOL(rtc_lock); /* Dummy RTC ops */ Index: linux/arch/sh/kernel/traps.c =================================================================== --- linux.orig/arch/sh/kernel/traps.c +++ linux/arch/sh/kernel/traps.c @@ -77,7 +77,7 @@ static void dump_mem(const char *str, un } } -static DEFINE_SPINLOCK(die_lock); +static DEFINE_RAW_SPINLOCK(die_lock); void die(const char * str, struct pt_regs * regs, long err) { Index: linux/arch/sh/mm/cache-sh4.c =================================================================== --- linux.orig/arch/sh/mm/cache-sh4.c +++ linux/arch/sh/mm/cache-sh4.c @@ -203,7 +203,7 @@ void flush_cache_sigtramp(unsigned long index = CACHE_IC_ADDRESS_ARRAY | (v & current_cpu_data.icache.entry_mask); - local_irq_save(flags); + raw_local_irq_save(flags); jump_to_P2(); for (i = 0; i < current_cpu_data.icache.ways; @@ -212,7 +212,7 @@ void flush_cache_sigtramp(unsigned long back_to_P1(); wmb(); - local_irq_restore(flags); + raw_local_irq_restore(flags); } static inline void flush_cache_4096(unsigned long start, @@ -228,10 +228,10 @@ static inline void flush_cache_4096(unsi (start < CACHE_OC_ADDRESS_ARRAY)) exec_offset = 0x20000000; - local_irq_save(flags); + raw_local_irq_save(flags); __flush_cache_4096(start | SH_CACHE_ASSOC, P1SEGADDR(phys), exec_offset); - local_irq_restore(flags); + raw_local_irq_restore(flags); } /* @@ -259,7 +259,7 @@ static inline void flush_icache_all(void { unsigned long flags, ccr; - local_irq_save(flags); + raw_local_irq_save(flags); jump_to_P2(); /* Flush I-cache */ @@ -273,7 +273,7 @@ static inline void flush_icache_all(void */ back_to_P1(); - local_irq_restore(flags); + raw_local_irq_restore(flags); } void flush_dcache_all(void) Index: linux/arch/sh/mm/init.c =================================================================== --- linux.orig/arch/sh/mm/init.c +++ linux/arch/sh/mm/init.c @@ -20,7 +20,7 @@ #include #include -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); pgd_t swapper_pg_dir[PTRS_PER_PGD]; void (*copy_page)(void *from, void *to); Index: linux/arch/sh/mm/pg-sh4.c =================================================================== --- linux.orig/arch/sh/mm/pg-sh4.c +++ linux/arch/sh/mm/pg-sh4.c @@ -39,9 +39,9 @@ void clear_user_page(void *to, unsigned entry = pfn_pte(phys_addr >> PAGE_SHIFT, PAGE_KERNEL); mutex_lock(&p3map_mutex[(address & CACHE_ALIAS)>>12]); set_pte(pte, entry); - local_irq_save(flags); + raw_local_irq_save(flags); flush_tlb_one(get_asid(), p3_addr); - local_irq_restore(flags); + raw_local_irq_restore(flags); update_mmu_cache(NULL, p3_addr, entry); __clear_user_page((void *)p3_addr, to); pte_clear(&init_mm, p3_addr, pte); @@ -75,9 +75,9 @@ void copy_user_page(void *to, void *from entry = pfn_pte(phys_addr >> PAGE_SHIFT, PAGE_KERNEL); mutex_lock(&p3map_mutex[(address & CACHE_ALIAS)>>12]); set_pte(pte, entry); - local_irq_save(flags); + raw_local_irq_save(flags); flush_tlb_one(get_asid(), p3_addr); - local_irq_restore(flags); + raw_local_irq_restore(flags); update_mmu_cache(NULL, p3_addr, entry); __copy_user_page((void *)p3_addr, from, to); pte_clear(&init_mm, p3_addr, pte); Index: linux/arch/sh/mm/tlb-flush.c =================================================================== --- linux.orig/arch/sh/mm/tlb-flush.c +++ linux/arch/sh/mm/tlb-flush.c @@ -24,7 +24,7 @@ void local_flush_tlb_page(struct vm_area asid = cpu_asid(cpu, vma->vm_mm); page &= PAGE_MASK; - local_irq_save(flags); + raw_local_irq_save(flags); if (vma->vm_mm != current->mm) { saved_asid = get_asid(); set_asid(asid); @@ -32,7 +32,7 @@ void local_flush_tlb_page(struct vm_area local_flush_tlb_one(asid, page); if (saved_asid != MMU_NO_ASID) set_asid(saved_asid); - local_irq_restore(flags); + raw_local_irq_restore(flags); } } @@ -46,7 +46,7 @@ void local_flush_tlb_range(struct vm_are unsigned long flags; int size; - local_irq_save(flags); + raw_local_irq_save(flags); size = (end - start + (PAGE_SIZE - 1)) >> PAGE_SHIFT; if (size > (MMU_NTLB_ENTRIES/4)) { /* Too many TLB to flush */ cpu_context(cpu, mm) = NO_CONTEXT; @@ -71,7 +71,7 @@ void local_flush_tlb_range(struct vm_are if (saved_asid != MMU_NO_ASID) set_asid(saved_asid); } - local_irq_restore(flags); + raw_local_irq_restore(flags); } } @@ -81,7 +81,7 @@ void local_flush_tlb_kernel_range(unsign unsigned long flags; int size; - local_irq_save(flags); + raw_local_irq_save(flags); size = (end - start + (PAGE_SIZE - 1)) >> PAGE_SHIFT; if (size > (MMU_NTLB_ENTRIES/4)) { /* Too many TLB to flush */ local_flush_tlb_all(); @@ -100,7 +100,7 @@ void local_flush_tlb_kernel_range(unsign } set_asid(saved_asid); } - local_irq_restore(flags); + raw_local_irq_restore(flags); } void local_flush_tlb_mm(struct mm_struct *mm) @@ -112,11 +112,11 @@ void local_flush_tlb_mm(struct mm_struct if (cpu_context(cpu, mm) != NO_CONTEXT) { unsigned long flags; - local_irq_save(flags); + raw_local_irq_save(flags); cpu_context(cpu, mm) = NO_CONTEXT; if (mm == current->mm) activate_context(mm, cpu); - local_irq_restore(flags); + raw_local_irq_restore(flags); } } @@ -131,10 +131,10 @@ void local_flush_tlb_all(void) * TF-bit for SH-3, TI-bit for SH-4. * It's same position, bit #2. */ - local_irq_save(flags); + raw_local_irq_save(flags); status = ctrl_inl(MMUCR); status |= 0x04; ctrl_outl(status, MMUCR); ctrl_barrier(); - local_irq_restore(flags); + raw_local_irq_restore(flags); } Index: linux/arch/sh/mm/tlb-sh4.c =================================================================== --- linux.orig/arch/sh/mm/tlb-sh4.c +++ linux/arch/sh/mm/tlb-sh4.c @@ -51,7 +51,7 @@ void update_mmu_cache(struct vm_area_str } } - local_irq_save(flags); + raw_local_irq_save(flags); /* Set PTEH register */ vpn = (address & MMU_VPN_MASK) | get_asid(); @@ -74,7 +74,7 @@ void update_mmu_cache(struct vm_area_str /* Load the TLB */ asm volatile("ldtlb": /* no output */ : /* no input */ : "memory"); - local_irq_restore(flags); + raw_local_irq_restore(flags); } void local_flush_tlb_one(unsigned long asid, unsigned long page) Index: linux/arch/sparc/kernel/smp.c =================================================================== --- linux.orig/arch/sparc/kernel/smp.c +++ linux/arch/sparc/kernel/smp.c @@ -68,16 +68,6 @@ void __cpuinit smp_store_cpu_info(int id cpu_data(id).prom_node = cpu_node; cpu_data(id).mid = cpu_get_hwmid(cpu_node); - /* this is required to tune the scheduler correctly */ - /* is it possible to have CPUs with different cache sizes? */ - if (id == boot_cpu_id) { - int cache_line,cache_nlines; - cache_line = 0x20; - cache_line = prom_getintdefault(cpu_node, "ecache-line-size", cache_line); - cache_nlines = 0x8000; - cache_nlines = prom_getintdefault(cpu_node, "ecache-nlines", cache_nlines); - max_cache_size = cache_line * cache_nlines; - } if (cpu_data(id).mid < 0) panic("No MID found for CPU%d at node 0x%08d", id, cpu_node); } Index: linux/arch/sparc/mm/highmem.c =================================================================== --- linux.orig/arch/sparc/mm/highmem.c +++ linux/arch/sparc/mm/highmem.c @@ -34,7 +34,7 @@ void *kmap_atomic(struct page *page, enu unsigned long idx; unsigned long vaddr; - /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ + preempt_disable(); pagefault_disable(); if (!PageHighMem(page)) return page_address(page); @@ -71,6 +71,7 @@ void kunmap_atomic(void *kvaddr, enum km if (vaddr < FIXADDR_START) { // FIXME pagefault_enable(); + preempt_enable(); return; } @@ -97,6 +98,7 @@ void kunmap_atomic(void *kvaddr, enum km #endif pagefault_enable(); + preempt_enable(); } /* We may be fed a pagetable here by ptep_to_xxx and others. */ Index: linux/arch/sparc64/Kconfig =================================================================== --- linux.orig/arch/sparc64/Kconfig +++ linux/arch/sparc64/Kconfig @@ -23,6 +23,10 @@ config GENERIC_TIME bool default y +config GENERIC_CMOS_UPDATE + bool + default y + config GENERIC_CLOCKEVENTS bool default y Index: linux/arch/sparc64/kernel/smp.c =================================================================== --- linux.orig/arch/sparc64/kernel/smp.c +++ linux/arch/sparc64/kernel/smp.c @@ -1163,32 +1163,6 @@ int setup_profiling_timer(unsigned int m return -EINVAL; } -static void __init smp_tune_scheduling(void) -{ - unsigned int smallest = ~0U; - int i; - - for (i = 0; i < NR_CPUS; i++) { - unsigned int val = cpu_data(i).ecache_size; - - if (val && val < smallest) - smallest = val; - } - - /* Any value less than 256K is nonsense. */ - if (smallest < (256U * 1024U)) - smallest = 256 * 1024; - - max_cache_size = smallest; - - if (smallest < 1U * 1024U * 1024U) - printk(KERN_INFO "Using max_cache_size of %uKB\n", - smallest / 1024U); - else - printk(KERN_INFO "Using max_cache_size of %uMB\n", - smallest / 1024U / 1024U); -} - /* Constrain the number of cpus to max_cpus. */ void __init smp_prepare_cpus(unsigned int max_cpus) { @@ -1206,7 +1180,6 @@ void __init smp_prepare_cpus(unsigned in } cpu_data(boot_cpu_id).udelay_val = loops_per_jiffy; - smp_tune_scheduling(); } void __devinit smp_prepare_boot_cpu(void) Index: linux/arch/sparc64/kernel/time.c =================================================================== --- linux.orig/arch/sparc64/kernel/time.c +++ linux/arch/sparc64/kernel/time.c @@ -403,58 +403,9 @@ static struct sparc64_tick_ops hbtick_op static unsigned long timer_ticks_per_nsec_quotient __read_mostly; -#define TICK_SIZE (tick_nsec / 1000) - -#define USEC_AFTER 500000 -#define USEC_BEFORE 500000 - -static void sync_cmos_clock(unsigned long dummy); - -static DEFINE_TIMER(sync_cmos_timer, sync_cmos_clock, 0, 0); - -static void sync_cmos_clock(unsigned long dummy) -{ - struct timeval now, next; - int fail = 1; - - /* - * If we have an externally synchronized Linux clock, then update - * CMOS clock accordingly every ~11 minutes. Set_rtc_mmss() has to be - * called as close as possible to 500 ms before the new second starts. - * This code is run on a timer. If the clock is set, that timer - * may not expire at the correct time. Thus, we adjust... - */ - if (!ntp_synced()) - /* - * Not synced, exit, do not restart a timer (if one is - * running, let it run out). - */ - return; - - do_gettimeofday(&now); - if (now.tv_usec >= USEC_AFTER - ((unsigned) TICK_SIZE) / 2 && - now.tv_usec <= USEC_BEFORE + ((unsigned) TICK_SIZE) / 2) - fail = set_rtc_mmss(now.tv_sec); - - next.tv_usec = USEC_AFTER - now.tv_usec; - if (next.tv_usec <= 0) - next.tv_usec += USEC_PER_SEC; - - if (!fail) - next.tv_sec = 659; - else - next.tv_sec = 0; - - if (next.tv_usec >= USEC_PER_SEC) { - next.tv_sec++; - next.tv_usec -= USEC_PER_SEC; - } - mod_timer(&sync_cmos_timer, jiffies + timeval_to_jiffies(&next)); -} - -void notify_arch_cmos_timer(void) +int update_persistent_clock(struct timespec now) { - mod_timer(&sync_cmos_timer, jiffies + 1); + return set_rtc_mmss(now.tv_sec); } /* Kick start a stopped clock (procedure from the Sun NVRAM/hostid FAQ). */ Index: linux/arch/x86_64/Kconfig =================================================================== --- linux.orig/arch/x86_64/Kconfig +++ linux/arch/x86_64/Kconfig @@ -28,10 +28,26 @@ config GENERIC_TIME bool default y +config GENERIC_CLOCKEVENTS_BROADCAST + bool + default y + +config GENERIC_CLOCKEVENTS + bool + default y + +config NONIRQ_WAKEUP + bool + default y + config GENERIC_TIME_VSYSCALL bool default y +config GENERIC_CMOS_UPDATE + bool + default y + config ZONE_DMA32 bool default y @@ -62,13 +78,6 @@ config ISA config SBUS bool -config RWSEM_GENERIC_SPINLOCK - bool - default y - -config RWSEM_XCHGADD_ALGORITHM - bool - config GENERIC_HWEIGHT bool default y @@ -126,6 +135,8 @@ source "init/Kconfig" menu "Processor type and features" +source "kernel/time/Kconfig" + choice prompt "Subarchitecture Type" default X86_PC @@ -343,6 +354,14 @@ config NUMA If the system is EM64T, you should say N unless your system is EM64T NUMA. +config RWSEM_GENERIC_SPINLOCK + bool + default y + +config RWSEM_XCHGADD_ALGORITHM + depends on !RWSEM_GENERIC_SPINLOCK && !PREEMPT_RT + bool + config K8_NUMA bool "Old style AMD Opteron NUMA detection" depends on NUMA && PCI @@ -698,6 +717,8 @@ source "drivers/acpi/Kconfig" source "arch/x86_64/kernel/cpufreq/Kconfig" +source "drivers/cpuidle/Kconfig" + endmenu menu "Bus options (PCI etc.)" Index: linux/arch/x86_64/ia32/ia32entry.S =================================================================== --- linux.orig/arch/x86_64/ia32/ia32entry.S +++ linux/arch/x86_64/ia32/ia32entry.S @@ -120,7 +120,9 @@ sysenter_do_call: cmpl $(IA32_NR_syscalls-1),%eax ja ia32_badsys IA32_ARG_FIXUP 1 + TRACE_SYS_IA32_CALL call *ia32_sys_call_table(,%rax,8) + TRACE_SYS_RET movq %rax,RAX-ARGOFFSET(%rsp) GET_THREAD_INFO(%r10) cli @@ -229,7 +231,9 @@ cstar_do_call: cmpl $IA32_NR_syscalls-1,%eax ja ia32_badsys IA32_ARG_FIXUP 1 + TRACE_SYS_IA32_CALL call *ia32_sys_call_table(,%rax,8) + TRACE_SYS_RET movq %rax,RAX-ARGOFFSET(%rsp) GET_THREAD_INFO(%r10) cli @@ -323,8 +327,10 @@ ia32_do_syscall: cmpl $(IA32_NR_syscalls-1),%eax ja ia32_badsys IA32_ARG_FIXUP + TRACE_SYS_IA32_CALL call *ia32_sys_call_table(,%rax,8) # xxx: rip relative ia32_sysret: + TRACE_SYS_RET movq %rax,RAX-ARGOFFSET(%rsp) jmp int_ret_from_sys_call @@ -394,7 +400,7 @@ END(ia32_ptregs_common) .section .rodata,"a" .align 8 -ia32_sys_call_table: +ENTRY(ia32_sys_call_table) .quad sys_restart_syscall .quad sys_exit .quad stub32_fork @@ -719,4 +725,7 @@ ia32_sys_call_table: .quad compat_sys_signalfd .quad compat_sys_timerfd .quad sys_eventfd +#ifdef CONFIG_EVENT_TRACE + .globl ia32_syscall_end +#endif ia32_syscall_end: Index: linux/arch/x86_64/kernel/Makefile =================================================================== --- linux.orig/arch/x86_64/kernel/Makefile +++ linux/arch/x86_64/kernel/Makefile @@ -9,7 +9,10 @@ obj-y := process.o signal.o entry.o trap x8664_ksyms.o i387.o syscall.o vsyscall.o \ setup64.o bootflag.o e820.o reboot.o quirks.o i8237.o \ pci-dma.o pci-nommu.o alternative.o hpet.o tsc.o bugs.o \ - perfctr-watchdog.o + perfctr-watchdog.o i8253.o + +i8253-y += ../../i386/kernel/i8253.o +hpet-y += ../../i386/kernel/hpet.o obj-$(CONFIG_STACKTRACE) += stacktrace.o obj-$(CONFIG_X86_MCE) += mce.o therm_throt.o Index: linux/arch/x86_64/kernel/apic.c =================================================================== --- linux.orig/arch/x86_64/kernel/apic.c +++ linux/arch/x86_64/kernel/apic.c @@ -25,6 +25,8 @@ #include #include #include +#include +#include #include #include @@ -38,10 +40,10 @@ #include #include #include +#include int apic_mapped; int apic_verbosity; -int apic_runs_main_timer; int apic_calibrate_pmtmr __initdata; int disable_apic_timer __initdata; @@ -50,20 +52,36 @@ int disable_apic_timer __initdata; int local_apic_timer_c2_ok; EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok); +/* Local APIC timer verification ok */ +static int local_apic_timer_verify_ok; + static struct resource *ioapic_resources; static struct resource lapic_resource = { .name = "Local APIC", .flags = IORESOURCE_MEM | IORESOURCE_BUSY, }; -/* - * cpu_mask that denotes the CPUs that needs timer interrupt coming in as - * IPIs in place of local APIC timers - */ -static cpumask_t timer_interrupt_broadcast_ipi_mask; +static unsigned int calibration_result; -/* Using APIC to generate smp_local_timer_interrupt? */ -int using_apic_timer __read_mostly = 0; +static int lapic_next_event(unsigned long delta, + struct clock_event_device *evt); +static void lapic_timer_setup(enum clock_event_mode mode, + struct clock_event_device *evt); + +static void lapic_timer_broadcast(cpumask_t mask); + +static struct clock_event_device lapic_clockevent = { + .name = "lapic", + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT + | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY, + .shift = 32, + .set_mode = lapic_timer_setup, + .set_next_event = lapic_next_event, + .broadcast = lapic_timer_broadcast, + .rating = 100, + .irq = -1, +}; +static DEFINE_PER_CPU(struct clock_event_device, lapic_events); static void apic_pm_activate(void); @@ -92,8 +110,9 @@ unsigned int safe_apic_wait_icr_idle(voi void enable_NMI_through_LVT0 (void * dummy) { unsigned int v; - - v = APIC_DM_NMI; /* unmask and set to NMI */ + + /* unmask and set to NMI */ + v = APIC_DM_NMI; apic_write(APIC_LVT0, v); } @@ -120,7 +139,7 @@ void ack_bad_irq(unsigned int irq) * holds up an irq slot - in excessive cases (when multiple * unexpected vectors occur) that might lock up the APIC * completely. - * But don't ack when the APIC is disabled. -AK + * But don't ack when the APIC is disabled. -AK */ if (!disable_apic) ack_APIC_irq(); @@ -453,7 +472,6 @@ void __cpuinit setup_local_APIC (void) oldvalue, value); } - nmi_watchdog_default(); setup_apic_nmi_watchdog(NULL); apic_pm_activate(); } @@ -616,7 +634,7 @@ early_param("apic", apic_set_verbosity); * Detect and enable local APICs on non-SMP boards. * Original code written by Keir Fraser. * On AMD64 we trust the BIOS - if it says no APIC it is likely - * not correctly set up (usually the APIC timer won't work etc.) + * not correctly set up (usually the APIC timer won't work etc.) */ static int __init detect_init_APIC (void) @@ -759,14 +777,14 @@ void __init init_apic_mappings(void) #define APIC_DIVISOR 16 -static void __setup_APIC_LVTT(unsigned int clocks) +static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen) { unsigned int lvtt_value, tmp_value; - int cpu = smp_processor_id(); - - lvtt_value = APIC_LVT_TIMER_PERIODIC | LOCAL_TIMER_VECTOR; - if (cpu_isset(cpu, timer_interrupt_broadcast_ipi_mask)) + lvtt_value = LOCAL_TIMER_VECTOR; + if (!oneshot) + lvtt_value |= APIC_LVT_TIMER_PERIODIC; + if (!irqen) lvtt_value |= APIC_LVT_MASKED; apic_write(APIC_LVTT, lvtt_value); @@ -779,227 +797,313 @@ static void __setup_APIC_LVTT(unsigned i & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE)) | APIC_TDR_DIV_16); - apic_write(APIC_TMICT, clocks/APIC_DIVISOR); + if (!oneshot) + apic_write(APIC_TMICT, clocks/APIC_DIVISOR); } -static void setup_APIC_timer(unsigned int clocks) +static int lapic_next_event(unsigned long delta, + struct clock_event_device *evt) +{ + apic_write(APIC_TMICT, delta); + return 0; +} + +static void lapic_timer_setup(enum clock_event_mode mode, + struct clock_event_device *evt) { unsigned long flags; + unsigned int v; + + /* Lapic used for broadcast ? */ + if (!local_apic_timer_verify_ok) + return; local_irq_save(flags); - /* wait for irq slice */ - if (hpet_address && hpet_use_timer) { - int trigger = hpet_readl(HPET_T0_CMP); - while (hpet_readl(HPET_COUNTER) >= trigger) - /* do nothing */ ; - while (hpet_readl(HPET_COUNTER) < trigger) - /* do nothing */ ; - } else { - int c1, c2; - outb_p(0x00, 0x43); - c2 = inb_p(0x40); - c2 |= inb_p(0x40) << 8; - do { - c1 = c2; - outb_p(0x00, 0x43); - c2 = inb_p(0x40); - c2 |= inb_p(0x40) << 8; - } while (c2 - c1 < 300); - } - __setup_APIC_LVTT(clocks); - /* Turn off PIT interrupt if we use APIC timer as main timer. - Only works with the PM timer right now - TBD fix it for HPET too. */ - if ((pmtmr_ioport != 0) && - smp_processor_id() == boot_cpu_id && - apic_runs_main_timer == 1 && - !cpu_isset(boot_cpu_id, timer_interrupt_broadcast_ipi_mask)) { - stop_timer_interrupt(); - apic_runs_main_timer++; + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + case CLOCK_EVT_MODE_ONESHOT: + __setup_APIC_LVTT(calibration_result, + mode != CLOCK_EVT_MODE_PERIODIC, 1); + break; + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_SHUTDOWN: + v = apic_read(APIC_LVTT); + v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR); + apic_write(APIC_LVTT, v); + break; + case CLOCK_EVT_MODE_RESUME: + /* Nothing to do here */ + break; } + local_irq_restore(flags); } /* - * In this function we calibrate APIC bus clocks to the external - * timer. Unfortunately we cannot use jiffies and the timer irq - * to calibrate, since some later bootup code depends on getting - * the first irq? Ugh. - * - * We want to do the calibration only once since we - * want to have local timer irqs syncron. CPUs connected - * by the same APIC bus have the very same bus frequency. - * And we want to have irqs off anyways, no accidental - * APIC irq that way. + * Local APIC timer broadcast function */ - -#define TICK_COUNT 100000000 - -static int __init calibrate_APIC_clock(void) +static void lapic_timer_broadcast(cpumask_t mask) { - unsigned apic, apic_start; - unsigned long tsc, tsc_start; - int result; - /* - * Put whatever arbitrary (but long enough) timeout - * value into the APIC clock, we just want to get the - * counter running for calibration. - */ - __setup_APIC_LVTT(4000000000); - - apic_start = apic_read(APIC_TMCCT); -#ifdef CONFIG_X86_PM_TIMER - if (apic_calibrate_pmtmr && pmtmr_ioport) { - pmtimer_wait(5000); /* 5ms wait */ - apic = apic_read(APIC_TMCCT); - result = (apic_start - apic) * 1000L / 5; - } else +#ifdef CONFIG_SMP + send_IPI_mask(mask, LOCAL_TIMER_VECTOR); #endif - { - rdtscll(tsc_start); +} - do { - apic = apic_read(APIC_TMCCT); - rdtscll(tsc); - } while ((tsc - tsc_start) < TICK_COUNT && - (apic_start - apic) < TICK_COUNT); +static void __devinit setup_APIC_timer(void) +{ + struct clock_event_device *levt = &__get_cpu_var(lapic_events); - result = (apic_start - apic) * 1000L * tsc_khz / - (tsc - tsc_start); - } - printk("result %d\n", result); + memcpy(levt, &lapic_clockevent, sizeof(*levt)); + levt->cpumask = cpumask_of_cpu(smp_processor_id()); + + clockevents_register_device(levt); +} + +/* + * In this functions we calibrate APIC bus clocks to the external timer. + * + * We want to do the calibration only once since we want to have local timer + * irqs syncron. CPUs connected by the same APIC bus have the very same bus + * frequency. + * + * This was previously done by reading the PIT/HPET and waiting for a wrap + * around to find out, that a tick has elapsed. I have a box, where the PIT + * readout is broken, so it never gets out of the wait loop again. This was + * also reported by others. + * + * Monitoring the jiffies value is inaccurate and the clockevents + * infrastructure allows us to do a simple substitution of the interrupt + * handler. + * + * The calibration routine also uses the pm_timer when possible, as the PIT + * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes + * back to normal later in the boot process). + */ +#define LAPIC_CAL_LOOPS (HZ/10) - printk(KERN_INFO "Detected %d.%03d MHz APIC timer.\n", - result / 1000 / 1000, result / 1000 % 1000); +static __initdata volatile int lapic_cal_loops = -1; +static __initdata long lapic_cal_t1, lapic_cal_t2; +static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2; +static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2; +static __initdata unsigned long lapic_cal_j1, lapic_cal_j2; - return result * APIC_DIVISOR / HZ; +/* + * Temporary interrupt handler. + */ +static void __init lapic_cal_handler(struct clock_event_device *dev) +{ + unsigned long long tsc = 0; + long tapic = apic_read(APIC_TMCCT); + unsigned long pm = acpi_pm_read_early(); + + if (cpu_has_tsc) + rdtscll(tsc); + + switch (lapic_cal_loops++) { + case 0: + lapic_cal_t1 = tapic; + lapic_cal_tsc1 = tsc; + lapic_cal_pm1 = pm; + lapic_cal_j1 = jiffies; + break; + + case LAPIC_CAL_LOOPS: + lapic_cal_t2 = tapic; + lapic_cal_tsc2 = tsc; + if (pm < lapic_cal_pm1) + pm += ACPI_PM_OVRRUN; + lapic_cal_pm2 = pm; + lapic_cal_j2 = jiffies; + break; + } } -static unsigned int calibration_result; - void __init setup_boot_APIC_clock (void) { - if (disable_apic_timer) { - printk(KERN_INFO "Disabling APIC timer\n"); - return; - } + struct clock_event_device *levt = &__get_cpu_var(lapic_events); + const long pm_100ms = PMTMR_TICKS_PER_SEC/10; + const long pm_thresh = pm_100ms/100; + void (*real_handler)(struct clock_event_device *dev); + unsigned long deltaj; + long delta, deltapm; + int pm_referenced = 0; + + /* + * The local apic timer can be disabled via the kernel + * commandline or from the test above. Register the lapic + * timer as a dummy clock event source on SMP systems, so the + * broadcast mechanism is used. On UP systems simply ignore it. + */ + if (disable_apic_timer) { + printk(KERN_INFO "Disabling APIC timer\n"); + /* No broadcast on UP ! */ + if (num_possible_cpus() > 1) + setup_APIC_timer(); + return; + } printk(KERN_INFO "Using local APIC timer interrupts.\n"); - using_apic_timer = 1; - local_irq_disable(); + /* Replace the global interrupt handler */ + real_handler = global_clock_event->event_handler; + global_clock_event->event_handler = lapic_cal_handler; - calibration_result = calibrate_APIC_clock(); /* - * Now set up the timer for real. + * Setup the APIC counter to 1e9. There is no way the lapic + * can underflow in the 100ms detection time frame */ - setup_APIC_timer(calibration_result); + __setup_APIC_LVTT(1000000000, 0, 0); + /* Let the interrupts run */ local_irq_enable(); -} -void __cpuinit setup_secondary_APIC_clock(void) -{ - local_irq_disable(); /* FIXME: Do we need this? --RR */ - setup_APIC_timer(calibration_result); - local_irq_enable(); -} + while (lapic_cal_loops <= LAPIC_CAL_LOOPS) + cpu_relax(); -void disable_APIC_timer(void) -{ - if (using_apic_timer) { - unsigned long v; + local_irq_disable(); - v = apic_read(APIC_LVTT); - /* - * When an illegal vector value (0-15) is written to an LVT - * entry and delivery mode is Fixed, the APIC may signal an - * illegal vector error, with out regard to whether the mask - * bit is set or whether an interrupt is actually seen on input. - * - * Boot sequence might call this function when the LVTT has - * '0' vector value. So make sure vector field is set to - * valid value. - */ - v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR); - apic_write(APIC_LVTT, v); + /* Restore the real event handler */ + global_clock_event->event_handler = real_handler; + + /* Build delta t1-t2 as apic timer counts down */ + delta = lapic_cal_t1 - lapic_cal_t2; + apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta); + + /* Check, if the PM timer is available */ + deltapm = lapic_cal_pm2 - lapic_cal_pm1; + apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm); + + if (deltapm) { + unsigned long mult; + u64 res; + + mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22); + + if (deltapm > (pm_100ms - pm_thresh) && + deltapm < (pm_100ms + pm_thresh)) { + apic_printk(APIC_VERBOSE, "... PM timer result ok\n"); + } else { + res = (((u64) deltapm) * mult) >> 22; + do_div(res, 1000000); + printk(KERN_WARNING "APIC calibration not consistent " + "with PM Timer: %ldms instead of 100ms\n", + (long)res); + /* Correct the lapic counter value */ + res = (((u64) delta ) * pm_100ms); + do_div(res, deltapm); + printk(KERN_INFO "APIC delta adjusted to PM-Timer: " + "%lu (%ld)\n", (unsigned long) res, delta); + delta = (long) res; + } + pm_referenced = 1; } -} -void enable_APIC_timer(void) -{ - int cpu = smp_processor_id(); + /* Calculate the scaled math multiplication factor */ + lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS, 32); + lapic_clockevent.max_delta_ns = + clockevent_delta2ns(0x7FFFFF, &lapic_clockevent); + lapic_clockevent.min_delta_ns = + clockevent_delta2ns(0xF, &lapic_clockevent); - if (using_apic_timer && - !cpu_isset(cpu, timer_interrupt_broadcast_ipi_mask)) { - unsigned long v; + calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS; - v = apic_read(APIC_LVTT); - apic_write(APIC_LVTT, v & ~APIC_LVT_MASKED); + apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta); + apic_printk(APIC_VERBOSE, "..... mult: %ld\n", lapic_clockevent.mult); + apic_printk(APIC_VERBOSE, "..... calibration result: %u\n", + calibration_result); + + if (cpu_has_tsc) { + delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1); + apic_printk(APIC_VERBOSE, "..... CPU clock speed is " + "%ld.%04ld MHz.\n", + (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ), + (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ)); } -} -void switch_APIC_timer_to_ipi(void *cpumask) -{ - cpumask_t mask = *(cpumask_t *)cpumask; - int cpu = smp_processor_id(); + apic_printk(APIC_VERBOSE, "..... host bus clock speed is " + "%u.%04u MHz.\n", + calibration_result / (1000000 / HZ), + calibration_result % (1000000 / HZ)); - if (cpu_isset(cpu, mask) && - !cpu_isset(cpu, timer_interrupt_broadcast_ipi_mask)) { - disable_APIC_timer(); - cpu_set(cpu, timer_interrupt_broadcast_ipi_mask); - } -} -EXPORT_SYMBOL(switch_APIC_timer_to_ipi); + local_apic_timer_verify_ok = 1; -void smp_send_timer_broadcast_ipi(void) -{ - int cpu = smp_processor_id(); - cpumask_t mask; + /* We trust the pm timer based calibration */ + if (!pm_referenced) { + apic_printk(APIC_VERBOSE, "... verify APIC timer\n"); - cpus_and(mask, cpu_online_map, timer_interrupt_broadcast_ipi_mask); + /* + * Setup the apic timer manually + */ + levt->event_handler = lapic_cal_handler; + lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt); + lapic_cal_loops = -1; - if (cpu_isset(cpu, mask)) { - cpu_clear(cpu, mask); - add_pda(apic_timer_irqs, 1); - smp_local_timer_interrupt(); - } + /* Let the interrupts run */ + local_irq_enable(); + + while(lapic_cal_loops <= LAPIC_CAL_LOOPS) + cpu_relax(); + + local_irq_disable(); + + /* Stop the lapic timer */ + lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt); + + local_irq_enable(); - if (!cpus_empty(mask)) { - send_IPI_mask(mask, LOCAL_TIMER_VECTOR); + /* Jiffies delta */ + deltaj = lapic_cal_j2 - lapic_cal_j1; + apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj); + + /* Check, if the jiffies result is consistent */ + if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2) + apic_printk(APIC_VERBOSE, "... jiffies result ok\n"); + else + local_apic_timer_verify_ok = 0; + } else + local_irq_enable(); + + if (!local_apic_timer_verify_ok) { + printk(KERN_WARNING + "APIC timer disabled due to verification failure.\n"); + /* No broadcast on UP ! */ + if (num_possible_cpus() == 1) + return; + } else { + /* + * If nmi_watchdog is set to IO_APIC, we need the + * PIT/HPET going. Otherwise register lapic as a dummy + * device. + */ + if (nmi_watchdog != NMI_IO_APIC) + lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY; } + + /* Setup the lapic or request the broadcast */ + setup_APIC_timer(); } -void switch_ipi_to_APIC_timer(void *cpumask) +void __cpuinit setup_secondary_APIC_clock(void) { - cpumask_t mask = *(cpumask_t *)cpumask; - int cpu = smp_processor_id(); - - if (cpu_isset(cpu, mask) && - cpu_isset(cpu, timer_interrupt_broadcast_ipi_mask)) { - cpu_clear(cpu, timer_interrupt_broadcast_ipi_mask); - enable_APIC_timer(); - } + setup_APIC_timer(); } -EXPORT_SYMBOL(switch_ipi_to_APIC_timer); int setup_profiling_timer(unsigned int multiplier) { return -EINVAL; } -void setup_APIC_extened_lvt(unsigned char lvt_off, unsigned char vector, - unsigned char msg_type, unsigned char mask) +void setup_APIC_extended_lvt(unsigned char lvt_off, unsigned char vector, + unsigned char msg_type, unsigned char mask) { unsigned long reg = (lvt_off << 4) + K8_APIC_EXT_LVT_BASE; unsigned int v = (mask << 16) | (msg_type << 8) | vector; + apic_write(reg, v); } -#undef APIC_DIVISOR - /* * Local timer interrupt handler. It does both profiling and * process statistics/rescheduling. @@ -1010,24 +1114,36 @@ void setup_APIC_extened_lvt(unsigned cha * value into /proc/profile. */ -void smp_local_timer_interrupt(void) +void local_apic_timer_interrupt(void) { - profile_tick(CPU_PROFILING); -#ifdef CONFIG_SMP - update_process_times(user_mode(get_irq_regs())); -#endif - if (apic_runs_main_timer > 1 && smp_processor_id() == boot_cpu_id) - main_timer_handler(); + int cpu = smp_processor_id(); + struct clock_event_device *evt = &per_cpu(lapic_events, cpu); + /* - * We take the 'long' return path, and there every subsystem - * grabs the appropriate locks (kernel lock/ irq lock). - * - * We might want to decouple profiling from the 'long path', - * and do the profiling totally in assembly. + * Normally we should not be here till LAPIC has been initialized but + * in some cases like kdump, its possible that there is a pending LAPIC + * timer interrupt from previous kernel's context and is delivered in + * new kernel the moment interrupts are enabled. * - * Currently this isn't too much of an issue (performance wise), - * we can take more than 100K local irqs per second on a 100 MHz P5. + * Interrupts are enabled early and LAPIC is setup much later, hence + * its possible that when we get here evt->event_handler is NULL. + * Check for event_handler being NULL and discard the interrupt as + * spurious. + */ + if (!evt->event_handler) { + printk(KERN_WARNING + "Spurious LAPIC timer interrupt on cpu %d\n", cpu); + /* Switch it off */ + lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt); + return; + } + + /* + * the NMI deadlock-detector uses this. */ + add_pda(apic_timer_irqs, 1); + + evt->event_handler(evt); } /* @@ -1043,11 +1159,6 @@ void smp_apic_timer_interrupt(struct pt_ struct pt_regs *old_regs = set_irq_regs(regs); /* - * the NMI deadlock-detector uses this. - */ - add_pda(apic_timer_irqs, 1); - - /* * NOTE! We'd better ACK the irq immediately, * because timer handling can be slow. */ @@ -1059,7 +1170,7 @@ void smp_apic_timer_interrupt(struct pt_ */ exit_idle(); irq_enter(); - smp_local_timer_interrupt(); + local_apic_timer_interrupt(); irq_exit(); set_irq_regs(old_regs); } @@ -1127,21 +1238,6 @@ asmlinkage void smp_spurious_interrupt(v v = apic_read(APIC_ISR + ((SPURIOUS_APIC_VECTOR & ~0x1f) >> 1)); if (v & (1 << (SPURIOUS_APIC_VECTOR & 0x1f))) ack_APIC_irq(); - -#if 0 - static unsigned long last_warning; - static unsigned long skipped; - - /* see sw-dev-man vol 3, chapter 7.4.13.5 */ - if (time_before(last_warning+30*HZ,jiffies)) { - printk(KERN_INFO "spurious APIC interrupt on CPU#%d, %ld skipped.\n", - smp_processor_id(), skipped); - last_warning = jiffies; - skipped = 0; - } else { - skipped++; - } -#endif irq_exit(); } @@ -1173,11 +1269,11 @@ asmlinkage void smp_error_interrupt(void 7: Illegal register address */ printk (KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n", - smp_processor_id(), v , v1); + smp_processor_id(), v , v1); irq_exit(); } -int disable_apic; +int disable_apic; /* * This initializes the IO-APIC and APIC hardware if this is @@ -1185,11 +1281,11 @@ int disable_apic; */ int __init APIC_init_uniprocessor (void) { - if (disable_apic) { + if (disable_apic) { printk(KERN_INFO "Apic disabled\n"); - return -1; + return -1; } - if (!cpu_has_apic) { + if (!cpu_has_apic) { disable_apic = 1; printk(KERN_INFO "Apic disabled by BIOS\n"); return -1; @@ -1211,8 +1307,8 @@ int __init APIC_init_uniprocessor (void) return 0; } -static __init int setup_disableapic(char *str) -{ +static __init int setup_disableapic(char *str) +{ disable_apic = 1; clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability); return 0; @@ -1220,10 +1316,10 @@ static __init int setup_disableapic(char early_param("disableapic", setup_disableapic); /* same as disableapic, for compatibility */ -static __init int setup_nolapic(char *str) -{ +static __init int setup_nolapic(char *str) +{ return setup_disableapic(str); -} +} early_param("nolapic", setup_nolapic); static int __init parse_lapic_timer_c2_ok(char *arg) @@ -1233,36 +1329,12 @@ static int __init parse_lapic_timer_c2_o } early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok); -static __init int setup_noapictimer(char *str) -{ +static __init int setup_noapictimer(char *str) +{ if (str[0] != ' ' && str[0] != 0) return 0; disable_apic_timer = 1; return 1; -} - -static __init int setup_apicmaintimer(char *str) -{ - apic_runs_main_timer = 1; - nohpet = 1; - return 1; } -__setup("apicmaintimer", setup_apicmaintimer); - -static __init int setup_noapicmaintimer(char *str) -{ - apic_runs_main_timer = -1; - return 1; -} -__setup("noapicmaintimer", setup_noapicmaintimer); - -static __init int setup_apicpmtimer(char *s) -{ - apic_calibrate_pmtmr = 1; - notsc_setup(NULL); - return setup_apicmaintimer(NULL); -} -__setup("apicpmtimer", setup_apicpmtimer); - -__setup("noapictimer", setup_noapictimer); +__setup("noapictimer", setup_noapictimer); Index: linux/arch/x86_64/kernel/crash.c =================================================================== --- linux.orig/arch/x86_64/kernel/crash.c +++ linux/arch/x86_64/kernel/crash.c @@ -62,11 +62,6 @@ static int crash_nmi_callback(struct not return 1; } -static void smp_send_nmi_allbutself(void) -{ - send_IPI_allbutself(NMI_VECTOR); -} - /* * This code is a best effort heuristic to get the * other cpus to stop executing. So races with Index: linux/arch/x86_64/kernel/early_printk.c =================================================================== --- linux.orig/arch/x86_64/kernel/early_printk.c +++ linux/arch/x86_64/kernel/early_printk.c @@ -202,7 +202,7 @@ static int early_console_initialized = 0 void early_printk(const char *fmt, ...) { - char buf[512]; + static char buf[512]; int n; va_list ap; Index: linux/arch/x86_64/kernel/entry.S =================================================================== --- linux.orig/arch/x86_64/kernel/entry.S +++ linux/arch/x86_64/kernel/entry.S @@ -53,6 +53,47 @@ .code64 +#ifdef CONFIG_EVENT_TRACE + +ENTRY(mcount) + cmpl $0, mcount_enabled + jz out + + push %rbp + mov %rsp,%rbp + + push %r11 + push %r10 + push %r9 + push %r8 + push %rdi + push %rsi + push %rdx + push %rcx + push %rax + + mov 0x0(%rbp),%rax + mov 0x8(%rbp),%rdi + mov 0x8(%rax),%rsi + + call __trace + + pop %rax + pop %rcx + pop %rdx + pop %rsi + pop %rdi + pop %r8 + pop %r9 + pop %r10 + pop %r11 + + pop %rbp +out: + ret + +#endif + #ifndef CONFIG_PREEMPT #define retint_kernel retint_restore_args #endif @@ -234,7 +275,9 @@ ENTRY(system_call) cmpq $__NR_syscall_max,%rax ja badsys movq %r10,%rcx + TRACE_SYS_CALL call *sys_call_table(,%rax,8) # XXX: rip relative + TRACE_SYS_RET movq %rax,RAX-ARGOFFSET(%rsp) /* * Syscall return path ending with SYSRET (fast path) @@ -267,8 +310,8 @@ sysret_check: /* Handle reschedules */ /* edx: work, edi: workmask */ sysret_careful: - bt $TIF_NEED_RESCHED,%edx - jnc sysret_signal + testl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edx + jz sysret_signal TRACE_IRQS_ON sti pushq %rdi @@ -291,7 +334,7 @@ sysret_signal: leaq -ARGOFFSET(%rsp),%rdi # &pt_regs -> arg1 xorl %esi,%esi # oldset -> arg2 call ptregscall_common -1: movl $_TIF_NEED_RESCHED,%edi +1: movl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edi /* Use IRET because user could have changed frame. This works because ptregscall_common has called FIXUP_TOP_OF_STACK. */ cli @@ -316,7 +359,9 @@ tracesys: cmova %rcx,%rax ja 1f movq %r10,%rcx /* fixup for C */ + TRACE_SYS_CALL call *sys_call_table(,%rax,8) + TRACE_SYS_RET 1: movq %rax,RAX-ARGOFFSET(%rsp) /* Use IRET because user could have changed frame */ @@ -344,8 +389,8 @@ int_with_check: /* First do a reschedule test. */ /* edx: work, edi: workmask */ int_careful: - bt $TIF_NEED_RESCHED,%edx - jnc int_very_careful + testl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edx + jz int_very_careful TRACE_IRQS_ON sti pushq %rdi @@ -380,7 +425,7 @@ int_signal: movq %rsp,%rdi # &ptregs -> arg1 xorl %esi,%esi # oldset -> arg2 call do_notify_resume -1: movl $_TIF_NEED_RESCHED,%edi +1: movl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edi int_restore_rest: RESTORE_REST cli @@ -584,8 +629,8 @@ bad_iret: /* edi: workmask, edx: work */ retint_careful: CFI_RESTORE_STATE - bt $TIF_NEED_RESCHED,%edx - jnc retint_signal + testl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edx + jz retint_signal TRACE_IRQS_ON sti pushq %rdi @@ -611,7 +656,7 @@ retint_signal: RESTORE_REST cli TRACE_IRQS_OFF - movl $_TIF_NEED_RESCHED,%edi + movl $(_TIF_NEED_RESCHED|_TIF_NEED_RESCHED_DELAYED),%edi GET_THREAD_INFO(%rcx) jmp retint_check Index: linux/arch/x86_64/kernel/head64.c =================================================================== --- linux.orig/arch/x86_64/kernel/head64.c +++ linux/arch/x86_64/kernel/head64.c @@ -10,6 +10,7 @@ #include #include #include +#include #include #include @@ -25,7 +26,11 @@ static void __init zap_identity_mappings { pgd_t *pgd = pgd_offset_k(0UL); pgd_clear(pgd); - __flush_tlb(); + /* + * preempt_disable/enable does not work this early in the + * bootup yet: + */ + write_cr3(read_cr3()); } /* Don't add a printk in there. printk relies on the PDA which is not initialized @@ -58,7 +63,7 @@ static void __init copy_bootdata(char *r memcpy(boot_command_line, command_line, COMMAND_LINE_SIZE); } -void __init x86_64_start_kernel(char * real_mode_data) +void __init notrace x86_64_start_kernel(char * real_mode_data) { int i; Index: linux/arch/x86_64/kernel/hpet.c =================================================================== --- linux.orig/arch/x86_64/kernel/hpet.c +++ /dev/null @@ -1,493 +0,0 @@ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define HPET_MASK 0xFFFFFFFF -#define HPET_SHIFT 22 - -/* FSEC = 10^-15 NSEC = 10^-9 */ -#define FSEC_PER_NSEC 1000000 - -int nohpet __initdata; - -unsigned long hpet_address; -unsigned long hpet_period; /* fsecs / HPET clock */ -unsigned long hpet_tick; /* HPET clocks / interrupt */ - -int hpet_use_timer; /* Use counter of hpet for time keeping, - * otherwise PIT - */ - -#ifdef CONFIG_HPET -static __init int late_hpet_init(void) -{ - struct hpet_data hd; - unsigned int ntimer; - - if (!hpet_address) - return 0; - - memset(&hd, 0, sizeof(hd)); - - ntimer = hpet_readl(HPET_ID); - ntimer = (ntimer & HPET_ID_NUMBER) >> HPET_ID_NUMBER_SHIFT; - ntimer++; - - /* - * Register with driver. - * Timer0 and Timer1 is used by platform. - */ - hd.hd_phys_address = hpet_address; - hd.hd_address = (void __iomem *)fix_to_virt(FIX_HPET_BASE); - hd.hd_nirqs = ntimer; - hd.hd_flags = HPET_DATA_PLATFORM; - hpet_reserve_timer(&hd, 0); -#ifdef CONFIG_HPET_EMULATE_RTC - hpet_reserve_timer(&hd, 1); -#endif - hd.hd_irq[0] = HPET_LEGACY_8254; - hd.hd_irq[1] = HPET_LEGACY_RTC; - if (ntimer > 2) { - struct hpet *hpet; - struct hpet_timer *timer; - int i; - - hpet = (struct hpet *) fix_to_virt(FIX_HPET_BASE); - timer = &hpet->hpet_timers[2]; - for (i = 2; i < ntimer; timer++, i++) - hd.hd_irq[i] = (timer->hpet_config & - Tn_INT_ROUTE_CNF_MASK) >> - Tn_INT_ROUTE_CNF_SHIFT; - - } - - hpet_alloc(&hd); - return 0; -} -fs_initcall(late_hpet_init); -#endif - -int hpet_timer_stop_set_go(unsigned long tick) -{ - unsigned int cfg; - -/* - * Stop the timers and reset the main counter. - */ - - cfg = hpet_readl(HPET_CFG); - cfg &= ~(HPET_CFG_ENABLE | HPET_CFG_LEGACY); - hpet_writel(cfg, HPET_CFG); - hpet_writel(0, HPET_COUNTER); - hpet_writel(0, HPET_COUNTER + 4); - -/* - * Set up timer 0, as periodic with first interrupt to happen at hpet_tick, - * and period also hpet_tick. - */ - if (hpet_use_timer) { - hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL | - HPET_TN_32BIT, HPET_T0_CFG); - hpet_writel(hpet_tick, HPET_T0_CMP); /* next interrupt */ - hpet_writel(hpet_tick, HPET_T0_CMP); /* period */ - cfg |= HPET_CFG_LEGACY; - } -/* - * Go! - */ - - cfg |= HPET_CFG_ENABLE; - hpet_writel(cfg, HPET_CFG); - - return 0; -} - -static cycle_t read_hpet(void) -{ - return (cycle_t)hpet_readl(HPET_COUNTER); -} - -static cycle_t __vsyscall_fn vread_hpet(void) -{ - return readl((void __iomem *)fix_to_virt(VSYSCALL_HPET) + 0xf0); -} - -struct clocksource clocksource_hpet = { - .name = "hpet", - .rating = 250, - .read = read_hpet, - .mask = (cycle_t)HPET_MASK, - .mult = 0, /* set below */ - .shift = HPET_SHIFT, - .flags = CLOCK_SOURCE_IS_CONTINUOUS, - .vread = vread_hpet, -}; - -int hpet_arch_init(void) -{ - unsigned int id; - u64 tmp; - - if (!hpet_address) - return -1; - set_fixmap_nocache(FIX_HPET_BASE, hpet_address); - __set_fixmap(VSYSCALL_HPET, hpet_address, PAGE_KERNEL_VSYSCALL_NOCACHE); - -/* - * Read the period, compute tick and quotient. - */ - - id = hpet_readl(HPET_ID); - - if (!(id & HPET_ID_VENDOR) || !(id & HPET_ID_NUMBER)) - return -1; - - hpet_period = hpet_readl(HPET_PERIOD); - if (hpet_period < 100000 || hpet_period > 100000000) - return -1; - - hpet_tick = (FSEC_PER_TICK + hpet_period / 2) / hpet_period; - - hpet_use_timer = (id & HPET_ID_LEGSUP); - - /* - * hpet period is in femto seconds per cycle - * so we need to convert this to ns/cyc units - * aproximated by mult/2^shift - * - * fsec/cyc * 1nsec/1000000fsec = nsec/cyc = mult/2^shift - * fsec/cyc * 1ns/1000000fsec * 2^shift = mult - * fsec/cyc * 2^shift * 1nsec/1000000fsec = mult - * (fsec/cyc << shift)/1000000 = mult - * (hpet_period << shift)/FSEC_PER_NSEC = mult - */ - tmp = (u64)hpet_period << HPET_SHIFT; - do_div(tmp, FSEC_PER_NSEC); - clocksource_hpet.mult = (u32)tmp; - clocksource_register(&clocksource_hpet); - - return hpet_timer_stop_set_go(hpet_tick); -} - -int hpet_reenable(void) -{ - return hpet_timer_stop_set_go(hpet_tick); -} - -/* - * calibrate_tsc() calibrates the processor TSC in a very simple way, comparing - * it to the HPET timer of known frequency. - */ - -#define TICK_COUNT 100000000 -#define TICK_MIN 5000 -#define MAX_TRIES 5 - -/* - * Some platforms take periodic SMI interrupts with 5ms duration. Make sure none - * occurs between the reads of the hpet & TSC. - */ -static void __init read_hpet_tsc(int *hpet, int *tsc) -{ - int tsc1, tsc2, hpet1, i; - - for (i = 0; i < MAX_TRIES; i++) { - tsc1 = get_cycles_sync(); - hpet1 = hpet_readl(HPET_COUNTER); - tsc2 = get_cycles_sync(); - if (tsc2 - tsc1 > TICK_MIN) - break; - } - *hpet = hpet1; - *tsc = tsc2; -} - -unsigned int __init hpet_calibrate_tsc(void) -{ - int tsc_start, hpet_start; - int tsc_now, hpet_now; - unsigned long flags; - - local_irq_save(flags); - - read_hpet_tsc(&hpet_start, &tsc_start); - - do { - local_irq_disable(); - read_hpet_tsc(&hpet_now, &tsc_now); - local_irq_restore(flags); - } while ((tsc_now - tsc_start) < TICK_COUNT && - (hpet_now - hpet_start) < TICK_COUNT); - - return (tsc_now - tsc_start) * 1000000000L - / ((hpet_now - hpet_start) * hpet_period / 1000); -} - -#ifdef CONFIG_HPET_EMULATE_RTC -/* HPET in LegacyReplacement Mode eats up RTC interrupt line. When, HPET - * is enabled, we support RTC interrupt functionality in software. - * RTC has 3 kinds of interrupts: - * 1) Update Interrupt - generate an interrupt, every sec, when RTC clock - * is updated - * 2) Alarm Interrupt - generate an interrupt at a specific time of day - * 3) Periodic Interrupt - generate periodic interrupt, with frequencies - * 2Hz-8192Hz (2Hz-64Hz for non-root user) (all freqs in powers of 2) - * (1) and (2) above are implemented using polling at a frequency of - * 64 Hz. The exact frequency is a tradeoff between accuracy and interrupt - * overhead. (DEFAULT_RTC_INT_FREQ) - * For (3), we use interrupts at 64Hz or user specified periodic - * frequency, whichever is higher. - */ -#include - -#define DEFAULT_RTC_INT_FREQ 64 -#define RTC_NUM_INTS 1 - -static unsigned long UIE_on; -static unsigned long prev_update_sec; - -static unsigned long AIE_on; -static struct rtc_time alarm_time; - -static unsigned long PIE_on; -static unsigned long PIE_freq = DEFAULT_RTC_INT_FREQ; -static unsigned long PIE_count; - -static unsigned long hpet_rtc_int_freq; /* RTC interrupt frequency */ -static unsigned int hpet_t1_cmp; /* cached comparator register */ - -int is_hpet_enabled(void) -{ - return hpet_address != 0; -} - -/* - * Timer 1 for RTC, we do not use periodic interrupt feature, - * even if HPET supports periodic interrupts on Timer 1. - * The reason being, to set up a periodic interrupt in HPET, we need to - * stop the main counter. And if we do that everytime someone diables/enables - * RTC, we will have adverse effect on main kernel timer running on Timer 0. - * So, for the time being, simulate the periodic interrupt in software. - * - * hpet_rtc_timer_init() is called for the first time and during subsequent - * interuppts reinit happens through hpet_rtc_timer_reinit(). - */ -int hpet_rtc_timer_init(void) -{ - unsigned int cfg, cnt; - unsigned long flags; - - if (!is_hpet_enabled()) - return 0; - /* - * Set the counter 1 and enable the interrupts. - */ - if (PIE_on && (PIE_freq > DEFAULT_RTC_INT_FREQ)) - hpet_rtc_int_freq = PIE_freq; - else - hpet_rtc_int_freq = DEFAULT_RTC_INT_FREQ; - - local_irq_save(flags); - - cnt = hpet_readl(HPET_COUNTER); - cnt += ((hpet_tick*HZ)/hpet_rtc_int_freq); - hpet_writel(cnt, HPET_T1_CMP); - hpet_t1_cmp = cnt; - - cfg = hpet_readl(HPET_T1_CFG); - cfg &= ~HPET_TN_PERIODIC; - cfg |= HPET_TN_ENABLE | HPET_TN_32BIT; - hpet_writel(cfg, HPET_T1_CFG); - - local_irq_restore(flags); - - return 1; -} - -static void hpet_rtc_timer_reinit(void) -{ - unsigned int cfg, cnt, ticks_per_int, lost_ints; - - if (unlikely(!(PIE_on | AIE_on | UIE_on))) { - cfg = hpet_readl(HPET_T1_CFG); - cfg &= ~HPET_TN_ENABLE; - hpet_writel(cfg, HPET_T1_CFG); - return; - } - - if (PIE_on && (PIE_freq > DEFAULT_RTC_INT_FREQ)) - hpet_rtc_int_freq = PIE_freq; - else - hpet_rtc_int_freq = DEFAULT_RTC_INT_FREQ; - - /* It is more accurate to use the comparator value than current count.*/ - ticks_per_int = hpet_tick * HZ / hpet_rtc_int_freq; - hpet_t1_cmp += ticks_per_int; - hpet_writel(hpet_t1_cmp, HPET_T1_CMP); - - /* - * If the interrupt handler was delayed too long, the write above tries - * to schedule the next interrupt in the past and the hardware would - * not interrupt until the counter had wrapped around. - * So we have to check that the comparator wasn't set to a past time. - */ - cnt = hpet_readl(HPET_COUNTER); - if (unlikely((int)(cnt - hpet_t1_cmp) > 0)) { - lost_ints = (cnt - hpet_t1_cmp) / ticks_per_int + 1; - /* Make sure that, even with the time needed to execute - * this code, the next scheduled interrupt has been moved - * back to the future: */ - lost_ints++; - - hpet_t1_cmp += lost_ints * ticks_per_int; - hpet_writel(hpet_t1_cmp, HPET_T1_CMP); - - if (PIE_on) - PIE_count += lost_ints; - - if (printk_ratelimit()) - printk(KERN_WARNING "rtc: lost some interrupts at %ldHz.\n", - hpet_rtc_int_freq); - } -} - -/* - * The functions below are called from rtc driver. - * Return 0 if HPET is not being used. - * Otherwise do the necessary changes and return 1. - */ -int hpet_mask_rtc_irq_bit(unsigned long bit_mask) -{ - if (!is_hpet_enabled()) - return 0; - - if (bit_mask & RTC_UIE) - UIE_on = 0; - if (bit_mask & RTC_PIE) - PIE_on = 0; - if (bit_mask & RTC_AIE) - AIE_on = 0; - - return 1; -} - -int hpet_set_rtc_irq_bit(unsigned long bit_mask) -{ - int timer_init_reqd = 0; - - if (!is_hpet_enabled()) - return 0; - - if (!(PIE_on | AIE_on | UIE_on)) - timer_init_reqd = 1; - - if (bit_mask & RTC_UIE) { - UIE_on = 1; - } - if (bit_mask & RTC_PIE) { - PIE_on = 1; - PIE_count = 0; - } - if (bit_mask & RTC_AIE) { - AIE_on = 1; - } - - if (timer_init_reqd) - hpet_rtc_timer_init(); - - return 1; -} - -int hpet_set_alarm_time(unsigned char hrs, unsigned char min, unsigned char sec) -{ - if (!is_hpet_enabled()) - return 0; - - alarm_time.tm_hour = hrs; - alarm_time.tm_min = min; - alarm_time.tm_sec = sec; - - return 1; -} - -int hpet_set_periodic_freq(unsigned long freq) -{ - if (!is_hpet_enabled()) - return 0; - - PIE_freq = freq; - PIE_count = 0; - - return 1; -} - -int hpet_rtc_dropped_irq(void) -{ - if (!is_hpet_enabled()) - return 0; - - return 1; -} - -irqreturn_t hpet_rtc_interrupt(int irq, void *dev_id, struct pt_regs *regs) -{ - struct rtc_time curr_time; - unsigned long rtc_int_flag = 0; - int call_rtc_interrupt = 0; - - hpet_rtc_timer_reinit(); - - if (UIE_on | AIE_on) { - rtc_get_rtc_time(&curr_time); - } - if (UIE_on) { - if (curr_time.tm_sec != prev_update_sec) { - /* Set update int info, call real rtc int routine */ - call_rtc_interrupt = 1; - rtc_int_flag = RTC_UF; - prev_update_sec = curr_time.tm_sec; - } - } - if (PIE_on) { - PIE_count++; - if (PIE_count >= hpet_rtc_int_freq/PIE_freq) { - /* Set periodic int info, call real rtc int routine */ - call_rtc_interrupt = 1; - rtc_int_flag |= RTC_PF; - PIE_count = 0; - } - } - if (AIE_on) { - if ((curr_time.tm_sec == alarm_time.tm_sec) && - (curr_time.tm_min == alarm_time.tm_min) && - (curr_time.tm_hour == alarm_time.tm_hour)) { - /* Set alarm int info, call real rtc int routine */ - call_rtc_interrupt = 1; - rtc_int_flag |= RTC_AF; - } - } - if (call_rtc_interrupt) { - rtc_int_flag |= (RTC_IRQF | (RTC_NUM_INTS << 8)); - rtc_interrupt(rtc_int_flag, dev_id); - } - return IRQ_HANDLED; -} -#endif - -static int __init nohpet_setup(char *s) -{ - nohpet = 1; - return 1; -} - -__setup("nohpet", nohpet_setup); Index: linux/arch/x86_64/kernel/i8259.c =================================================================== --- linux.orig/arch/x86_64/kernel/i8259.c +++ linux/arch/x86_64/kernel/i8259.c @@ -96,8 +96,8 @@ static void (*interrupt[NR_VECTORS - FIR */ static int i8259A_auto_eoi; -DEFINE_SPINLOCK(i8259A_lock); static void mask_and_ack_8259A(unsigned int); +DEFINE_RAW_SPINLOCK(i8259A_lock); static struct irq_chip i8259A_chip = { .name = "XT-PIC", @@ -395,7 +395,8 @@ device_initcall(i8259A_init_sysfs); * IRQ2 is cascade interrupt to second interrupt controller */ -static struct irqaction irq2 = { no_action, 0, CPU_MASK_NONE, "cascade", NULL, NULL}; +static struct irqaction irq2 = { no_action, IRQF_NODELAY, CPU_MASK_NONE, "cascade", NULL, NULL}; + DEFINE_PER_CPU(vector_irq_t, vector_irq) = { [0 ... IRQ0_VECTOR - 1] = -1, [IRQ0_VECTOR] = 0, @@ -460,47 +461,6 @@ void invalidate_interrupt6(void); void invalidate_interrupt7(void); void thermal_interrupt(void); void threshold_interrupt(void); -void i8254_timer_resume(void); - -static void setup_timer_hardware(void) -{ - outb_p(0x34,0x43); /* binary, mode 2, LSB/MSB, ch 0 */ - udelay(10); - outb_p(LATCH & 0xff , 0x40); /* LSB */ - udelay(10); - outb(LATCH >> 8 , 0x40); /* MSB */ -} - -static int timer_resume(struct sys_device *dev) -{ - setup_timer_hardware(); - return 0; -} - -void i8254_timer_resume(void) -{ - setup_timer_hardware(); -} - -static struct sysdev_class timer_sysclass = { - set_kset_name("timer_pit"), - .resume = timer_resume, -}; - -static struct sys_device device_timer = { - .id = 0, - .cls = &timer_sysclass, -}; - -static int __init init_timer_sysfs(void) -{ - int error = sysdev_class_register(&timer_sysclass); - if (!error) - error = sysdev_register(&device_timer); - return error; -} - -device_initcall(init_timer_sysfs); void __init init_IRQ(void) { @@ -551,12 +511,6 @@ void __init init_IRQ(void) set_intr_gate(SPURIOUS_APIC_VECTOR, spurious_interrupt); set_intr_gate(ERROR_APIC_VECTOR, error_interrupt); - /* - * Set the clock to HZ Hz, we already have a valid - * vector now: - */ - setup_timer_hardware(); - if (!acpi_ioapic) setup_irq(2, &irq2); } Index: linux/arch/x86_64/kernel/io_apic.c =================================================================== --- linux.orig/arch/x86_64/kernel/io_apic.c +++ linux/arch/x86_64/kernel/io_apic.c @@ -90,8 +90,8 @@ int timer_over_8254 __initdata = 1; /* Where if anywhere is the i8259 connect in external int mode */ static struct { int pin, apic; } ioapic_i8259 = { -1, -1 }; -static DEFINE_SPINLOCK(ioapic_lock); -DEFINE_SPINLOCK(vector_lock); +static DEFINE_RAW_SPINLOCK(ioapic_lock); +DEFINE_RAW_SPINLOCK(vector_lock); /* * # of IRQ routing registers @@ -178,6 +178,9 @@ static inline void io_apic_sync(unsigned reg ACTION; \ io_apic_modify(entry->apic, reg); \ FINAL; \ + /* Force POST flush by reading: */ \ + reg = io_apic_read(entry->apic, 0x10 + R + pin*2); \ + \ if (!entry->next) \ break; \ entry = irq_2_pin + entry->next; \ @@ -322,10 +325,11 @@ static void add_pin_to_irq(unsigned int static void name##_IO_APIC_irq (unsigned int irq) \ __DO_ACTION(R, ACTION, FINAL) -DO_ACTION( __mask, 0, |= 0x00010000, io_apic_sync(entry->apic) ) - /* mask = 1 */ -DO_ACTION( __unmask, 0, &= 0xfffeffff, ) - /* mask = 0 */ +DO_ACTION( __mask, 0, |= 0x00010000, ) /* mask = 1 */ +DO_ACTION( __unmask, 0, &= 0xfffeffff, ) /* mask = 0 */ + +DO_ACTION( __pcix_mask, 0, &= 0xffff7fff, ) /* edge */ +DO_ACTION( __pcix_unmask, 0, = (reg & 0xfffeffff) | 0x00008000, ) /* level */ static void mask_IO_APIC_irq (unsigned int irq) { @@ -344,6 +348,23 @@ static void unmask_IO_APIC_irq (unsigned __unmask_IO_APIC_irq(irq); spin_unlock_irqrestore(&ioapic_lock, flags); } +static void pcix_mask_IO_APIC_irq (unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&ioapic_lock, flags); + __pcix_mask_IO_APIC_irq(irq); + spin_unlock_irqrestore(&ioapic_lock, flags); +} + +static void pcix_unmask_IO_APIC_irq (unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&ioapic_lock, flags); + __pcix_unmask_IO_APIC_irq(irq); + spin_unlock_irqrestore(&ioapic_lock, flags); +} static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin) { @@ -771,15 +792,18 @@ void __setup_vector_irq(int cpu) static struct irq_chip ioapic_chip; +static struct irq_chip pcix_ioapic_chip; -static void ioapic_register_intr(int irq, unsigned long trigger) +static void ioapic_register_intr(int irq, unsigned long trigger, int pcix) { + struct irq_chip *chip = pcix ? &pcix_ioapic_chip : &ioapic_chip; + if (trigger) - set_irq_chip_and_handler_name(irq, &ioapic_chip, - handle_fasteoi_irq, "fasteoi"); + set_irq_chip_and_handler_name(irq, chip, handle_fasteoi_irq, + pcix ? "pcix-fasteoi" : "fasteoi"); else - set_irq_chip_and_handler_name(irq, &ioapic_chip, - handle_edge_irq, "edge"); + set_irq_chip_and_handler_name(irq, chip, handle_edge_irq, + pcix ? "pcix-edge" : "edge"); } static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, @@ -823,7 +847,7 @@ static void setup_IO_APIC_irq(int apic, if (trigger) entry.mask = 1; - ioapic_register_intr(irq, trigger); + ioapic_register_intr(irq, trigger, apic > 0); if (irq < 16) disable_8259A_irq(irq); @@ -1405,7 +1429,8 @@ static void ack_apic_level(unsigned int irq_complete_move(irq); #if defined(CONFIG_GENERIC_PENDING_IRQ) || defined(CONFIG_IRQBALANCE) /* If we are moving the irq we need to mask it */ - if (unlikely(irq_desc[irq].status & IRQ_MOVE_PENDING)) { + if (unlikely(irq_desc[irq].status & IRQ_MOVE_PENDING) && + !(irq_desc[irq].status & IRQ_INPROGRESS)) { do_unmask_irq = 1; mask_IO_APIC_irq(irq); } @@ -1424,14 +1449,27 @@ static void ack_apic_level(unsigned int } static struct irq_chip ioapic_chip __read_mostly = { - .name = "IO-APIC", - .startup = startup_ioapic_irq, - .mask = mask_IO_APIC_irq, - .unmask = unmask_IO_APIC_irq, - .ack = ack_apic_edge, - .eoi = ack_apic_level, + .name = "IO-APIC", + .startup = startup_ioapic_irq, + .mask = mask_IO_APIC_irq, + .unmask = unmask_IO_APIC_irq, + .ack = ack_apic_edge, + .eoi = ack_apic_level, +#ifdef CONFIG_SMP + .set_affinity = set_ioapic_affinity_irq, +#endif + .retrigger = ioapic_retrigger_irq, +}; + +static struct irq_chip pcix_ioapic_chip __read_mostly = { + .name = "IO-APIC", + .startup = startup_ioapic_irq, + .mask = pcix_mask_IO_APIC_irq, + .unmask = pcix_unmask_IO_APIC_irq, + .ack = ack_apic_edge, + .eoi = ack_apic_level, #ifdef CONFIG_SMP - .set_affinity = set_ioapic_affinity_irq, + .set_affinity = set_ioapic_affinity_irq, #endif .retrigger = ioapic_retrigger_irq, }; @@ -1628,7 +1666,6 @@ static inline void check_timer(void) */ unmask_IO_APIC_irq(0); if (!no_timer_check && timer_irq_works()) { - nmi_watchdog_default(); if (nmi_watchdog == NMI_IO_APIC) { disable_8259A_irq(0); setup_nmi(); @@ -1654,7 +1691,6 @@ static inline void check_timer(void) setup_ExtINT_IRQ0_pin(apic2, pin2, cfg->vector); if (timer_irq_works()) { apic_printk(APIC_VERBOSE," works.\n"); - nmi_watchdog_default(); if (nmi_watchdog == NMI_IO_APIC) { setup_nmi(); } Index: linux/arch/x86_64/kernel/irq.c =================================================================== --- linux.orig/arch/x86_64/kernel/irq.c +++ linux/arch/x86_64/kernel/irq.c @@ -111,10 +111,18 @@ asmlinkage unsigned int do_IRQ(struct pt unsigned vector = ~regs->orig_rax; unsigned irq; + irq_show_regs_callback(smp_processor_id(), regs); + exit_idle(); irq_enter(); irq = __get_cpu_var(vector_irq)[vector]; +#ifdef CONFIG_EVENT_TRACE + if (irq == trace_user_trigger_irq) + user_trace_start(); +#endif + trace_special(regs->rip, irq, 0); + #ifdef CONFIG_DEBUG_STACKOVERFLOW stack_overflow_check(regs); #endif Index: linux/arch/x86_64/kernel/kprobes.c =================================================================== --- linux.orig/arch/x86_64/kernel/kprobes.c +++ linux/arch/x86_64/kernel/kprobes.c @@ -658,11 +658,9 @@ int __kprobes kprobe_exceptions_notify(s case DIE_GPF: case DIE_PAGE_FAULT: /* kprobe_running() needs smp_processor_id() */ - preempt_disable(); - if (kprobe_running() && + if (per_cpu(current_kprobe, raw_smp_processor_id()) && kprobe_fault_handler(args->regs, args->trapnr)) ret = NOTIFY_STOP; - preempt_enable(); break; default: break; Index: linux/arch/x86_64/kernel/mce_amd.c =================================================================== --- linux.orig/arch/x86_64/kernel/mce_amd.c +++ linux/arch/x86_64/kernel/mce_amd.c @@ -157,9 +157,9 @@ void __cpuinit mce_amd_feature_init(stru high |= K8_APIC_EXT_LVT_ENTRY_THRESHOLD << 20; wrmsr(address, low, high); - setup_APIC_extened_lvt(K8_APIC_EXT_LVT_ENTRY_THRESHOLD, - THRESHOLD_APIC_VECTOR, - K8_APIC_EXT_INT_MSG_FIX, 0); + setup_APIC_extended_lvt(K8_APIC_EXT_LVT_ENTRY_THRESHOLD, + THRESHOLD_APIC_VECTOR, + K8_APIC_EXT_INT_MSG_FIX, 0); threshold_defaults.address = address; threshold_restart_bank(&threshold_defaults, 0, 0); Index: linux/arch/x86_64/kernel/nmi.c =================================================================== --- linux.orig/arch/x86_64/kernel/nmi.c +++ linux/arch/x86_64/kernel/nmi.c @@ -22,11 +22,13 @@ #include #include #include +#include #include #include #include #include +#include int unknown_nmi_panic; int nmi_watchdog_enabled; @@ -44,7 +46,7 @@ atomic_t nmi_active = ATOMIC_INIT(0); / int panic_on_timeout; unsigned int nmi_watchdog = NMI_DEFAULT; -static unsigned int nmi_hz = HZ; +static unsigned int nmi_hz = 1000; static DEFINE_PER_CPU(short, wd_enabled); @@ -52,7 +54,7 @@ static DEFINE_PER_CPU(short, wd_enabled) static int unknown_nmi_panic_callback(struct pt_regs *regs, int cpu); /* Run after command line and cpu_init init, but before all other checks */ -void nmi_watchdog_default(void) +static inline void nmi_watchdog_default(void) { if (nmi_watchdog != NMI_DEFAULT) return; @@ -68,7 +70,9 @@ static int endflag __initdata = 0; */ static __init void nmi_cpu_busy(void *data) { +#ifndef CONFIG_PREEMPT_RT local_irq_enable_in_hardirq(); +#endif /* Intentionally don't use cpu_relax here. This is to make sure that the performance counter really ticks, even if there is a simulator or similar that catches the @@ -302,7 +306,7 @@ void touch_nmi_watchdog (void) unsigned cpu; /* - * Tell other CPUs to reset their alert counters. We cannot + * Tell other CPUs to reset their alert counters. We cannot * do it ourselves because the alert count increase is not * atomic. */ @@ -310,16 +314,54 @@ void touch_nmi_watchdog (void) per_cpu(nmi_touch, cpu) = 1; } - touch_softlockup_watchdog(); + touch_softlockup_watchdog(); +} + +int nmi_show_regs[NR_CPUS]; + +void nmi_show_all_regs(void) +{ + int i; + + if (system_state == SYSTEM_BOOTING) + return; + + smp_send_nmi_allbutself(); + + for_each_online_cpu(i) + nmi_show_regs[i] = 1; + + for_each_online_cpu(i) { + while (nmi_show_regs[i] == 1) + barrier(); + } +} + +static DEFINE_RAW_SPINLOCK(nmi_print_lock); + +notrace void irq_show_regs_callback(int cpu, struct pt_regs *regs) +{ + if (!nmi_show_regs[cpu]) + return; + + nmi_show_regs[cpu] = 0; + spin_lock(&nmi_print_lock); + printk(KERN_WARNING "NMI show regs on CPU#%d:\n", cpu); + printk(KERN_WARNING "apic_timer_irqs: %d\n", read_pda(apic_timer_irqs)); + show_regs(regs); + spin_unlock(&nmi_print_lock); } -int __kprobes nmi_watchdog_tick(struct pt_regs * regs, unsigned reason) +int notrace __kprobes nmi_watchdog_tick(struct pt_regs * regs, unsigned reason) { int sum; int touched = 0; int cpu = smp_processor_id(); int rc = 0; + irq_show_regs_callback(cpu, regs); + __profile_tick(CPU_PROFILING, regs); + /* check for other users first */ if (notify_die(DIE_NMI, "nmi", regs, reason, 2, SIGINT) == NOTIFY_STOP) { @@ -328,6 +370,7 @@ int __kprobes nmi_watchdog_tick(struct p } sum = read_pda(apic_timer_irqs); + if (__get_cpu_var(nmi_touch)) { __get_cpu_var(nmi_touch) = 0; touched = 1; @@ -356,9 +399,20 @@ int __kprobes nmi_watchdog_tick(struct p * wait a few IRQs (5 seconds) before doing the oops ... */ local_inc(&__get_cpu_var(alert_counter)); - if (local_read(&__get_cpu_var(alert_counter)) == 5*nmi_hz) + if (local_read(&__get_cpu_var(alert_counter)) == 5*nmi_hz) { + int i; + + for_each_online_cpu(i) { + if (i == cpu) + continue; + nmi_show_regs[i] = 1; + while (nmi_show_regs[i] == 1) + cpu_relax(); + } + die_nmi("NMI Watchdog detected LOCKUP on CPU %d\n", regs, panic_on_timeout); + } } else { __get_cpu_var(last_irq_sum) = sum; local_set(&__get_cpu_var(alert_counter), 0); @@ -461,6 +515,13 @@ void __trigger_all_cpu_backtrace(void) } } +void smp_send_nmi_allbutself(void) +{ +#ifdef CONFIG_SMP + send_IPI_allbutself(NMI_VECTOR); +#endif +} + EXPORT_SYMBOL(nmi_active); EXPORT_SYMBOL(nmi_watchdog); EXPORT_SYMBOL(touch_nmi_watchdog); Index: linux/arch/x86_64/kernel/process.c =================================================================== --- linux.orig/arch/x86_64/kernel/process.c +++ linux/arch/x86_64/kernel/process.c @@ -37,6 +37,7 @@ #include #include #include +#include #include #include @@ -115,7 +116,7 @@ static void default_idle(void) */ smp_mb(); local_irq_disable(); - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { /* Enables interrupts one instruction before HLT. x86 special cases this so there is no race. */ safe_halt(); @@ -201,12 +202,14 @@ void cpu_idle (void) current_thread_info()->status |= TS_POLLING; /* endless idle loop with no priority at all */ while (1) { - while (!need_resched()) { + while (!need_resched() && !need_resched_delayed()) { void (*idle)(void); if (__get_cpu_var(cpu_idle_state)) __get_cpu_var(cpu_idle_state) = 0; + tick_nohz_stop_sched_tick(); + rmb(); idle = pm_idle; if (!idle) @@ -227,9 +230,14 @@ void cpu_idle (void) __exit_idle(); } - preempt_enable_no_resched(); - schedule(); + tick_nohz_restart_sched_tick(); + local_irq_disable(); + trace_preempt_exit_idle(); + __preempt_enable_no_resched(); + __schedule(); preempt_disable(); + trace_preempt_enter_idle(); + local_irq_enable(); } } @@ -245,10 +253,10 @@ void cpu_idle (void) */ void mwait_idle_with_hints(unsigned long eax, unsigned long ecx) { - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { __monitor((void *)¤t_thread_info()->flags, 0, 0); smp_mb(); - if (!need_resched()) + if (!need_resched() && !need_resched_delayed()) __mwait(eax, ecx); } } @@ -256,12 +264,13 @@ void mwait_idle_with_hints(unsigned long /* Default MONITOR/MWAIT with no hints, used for default C1 state */ static void mwait_idle(void) { - if (!need_resched()) { + if (!need_resched() && !need_resched_delayed()) { __monitor((void *)¤t_thread_info()->flags, 0, 0); smp_mb(); - if (!need_resched()) + if (!need_resched() && !need_resched_delayed()) { + trace_hardirqs_on(); __sti_mwait(0, 0); - else + } else local_irq_enable(); } else { local_irq_enable(); @@ -367,7 +376,7 @@ void exit_thread(void) struct thread_struct *t = &me->thread; if (me->thread.io_bitmap_ptr) { - struct tss_struct *tss = &per_cpu(init_tss, get_cpu()); + struct tss_struct *tss; kfree(t->io_bitmap_ptr); t->io_bitmap_ptr = NULL; @@ -375,6 +384,7 @@ void exit_thread(void) /* * Careful, clear this in the TSS too: */ + tss = &per_cpu(init_tss, get_cpu()); memset(tss->io_bitmap, 0xff, t->io_bitmap_max); t->io_bitmap_max = 0; put_cpu(); Index: linux/arch/x86_64/kernel/setup64.c =================================================================== --- linux.orig/arch/x86_64/kernel/setup64.c +++ linux/arch/x86_64/kernel/setup64.c @@ -114,7 +114,7 @@ void __init setup_per_cpu_areas(void) } } -void pda_init(int cpu) +void notrace pda_init(int cpu) { struct x8664_pda *pda = cpu_pda(cpu); @@ -191,7 +191,7 @@ unsigned long kernel_eflags; * 'CPU state barrier', nothing should get across. * A lot of state is already set up in PDA init. */ -void __cpuinit cpu_init (void) +void __cpuinit notrace cpu_init (void) { int cpu = stack_smp_processor_id(); struct tss_struct *t = &per_cpu(init_tss, cpu); Index: linux/arch/x86_64/kernel/signal.c =================================================================== --- linux.orig/arch/x86_64/kernel/signal.c +++ linux/arch/x86_64/kernel/signal.c @@ -395,6 +395,13 @@ static void do_signal(struct pt_regs *re int signr; sigset_t *oldset; +#ifdef CONFIG_PREEMPT_RT + /* + * Fully-preemptible kernel does not need interrupts disabled: + */ + local_irq_enable(); + preempt_check_resched(); +#endif /* * We want the common case to go fast, which * is why we may in certain cases get here from Index: linux/arch/x86_64/kernel/smp.c =================================================================== --- linux.orig/arch/x86_64/kernel/smp.c +++ linux/arch/x86_64/kernel/smp.c @@ -56,7 +56,7 @@ union smp_flush_state { struct mm_struct *flush_mm; unsigned long flush_va; #define FLUSH_ALL -1ULL - spinlock_t tlbstate_lock; + raw_spinlock_t tlbstate_lock; }; char pad[SMP_CACHE_BYTES]; } ____cacheline_aligned; @@ -295,10 +295,20 @@ void smp_send_reschedule(int cpu) } /* + * this function sends a 'reschedule' IPI to all other CPUs. + * This is used when RT tasks are starving and other CPUs + * might be able to run them: + */ +void smp_send_reschedule_allbutself(void) +{ + send_IPI_allbutself(RESCHEDULE_VECTOR); +} + +/* * Structure and data for smp_call_function(). This is designed to minimise * static memory requirements. It also looks cleaner. */ -static DEFINE_SPINLOCK(call_lock); +static DEFINE_RAW_SPINLOCK(call_lock); struct call_data_struct { void (*func) (void *info); Index: linux/arch/x86_64/kernel/smpboot.c =================================================================== --- linux.orig/arch/x86_64/kernel/smpboot.c +++ linux/arch/x86_64/kernel/smpboot.c @@ -223,8 +223,6 @@ void __cpuinit smp_callin(void) local_irq_disable(); Dprintk("Stack at about %p\n",&cpuid); - disable_APIC_timer(); - /* * Save our processor parameters */ @@ -318,7 +316,7 @@ static inline void set_cpu_sibling_map(i /* * Setup code on secondary processor (after comming out of the trampoline) */ -void __cpuinit start_secondary(void) +void __cpuinit notrace start_secondary(void) { /* * Dont put anything before smp_callin(), SMP @@ -333,8 +331,8 @@ void __cpuinit start_secondary(void) barrier(); /* - * Check TSC sync first: - */ + * Check TSC sync first: + */ check_tsc_sync_target(); Dprintk("cpu %d: setting up apic clock\n", smp_processor_id()); @@ -348,8 +346,6 @@ void __cpuinit start_secondary(void) enable_8259A_irq(0); } - enable_APIC_timer(); - /* * The sibling maps must be set before turing the online map on for * this cpu @@ -854,7 +850,6 @@ static int __init smp_sanity_check(unsig */ void __init smp_prepare_cpus(unsigned int max_cpus) { - nmi_watchdog_default(); current_cpu_data = boot_cpu_data; current_thread_info()->cpu = 0; /* needed? */ set_cpu_sibling_map(0); Index: linux/arch/x86_64/kernel/time.c =================================================================== --- linux.orig/arch/x86_64/kernel/time.c +++ linux/arch/x86_64/kernel/time.c @@ -28,11 +28,12 @@ #include #include #include +#include #ifdef CONFIG_ACPI #include /* for PM timer frequency */ #include #endif -#include +#include #include #include #include @@ -44,12 +45,10 @@ #include #include #include - -static char *timename = NULL; +#include DEFINE_SPINLOCK(rtc_lock); EXPORT_SYMBOL(rtc_lock); -DEFINE_SPINLOCK(i8253_lock); volatile unsigned long __jiffies __section_jiffies = INITIAL_JIFFIES; @@ -79,8 +78,9 @@ EXPORT_SYMBOL(profile_pc); * sheet for details. */ -static void set_rtc_mmss(unsigned long nowtime) +static int set_rtc_mmss(unsigned long nowtime) { + int retval = 0; int real_seconds, real_minutes, cmos_minutes; unsigned char control, freq_select; @@ -120,6 +120,7 @@ static void set_rtc_mmss(unsigned long n if (abs(real_minutes - cmos_minutes) >= 30) { printk(KERN_WARNING "time.c: can't update CMOS clock " "from %d to %d\n", cmos_minutes, real_minutes); + retval = -1; } else { BIN_TO_BCD(real_seconds); BIN_TO_BCD(real_minutes); @@ -139,67 +140,23 @@ static void set_rtc_mmss(unsigned long n CMOS_WRITE(freq_select, RTC_FREQ_SELECT); spin_unlock(&rtc_lock); -} + return retval; +} -void main_timer_handler(void) +int update_persistent_clock(struct timespec now) { - static unsigned long rtc_update = 0; -/* - * Here we are in the timer irq handler. We have irqs locally disabled (so we - * don't need spin_lock_irqsave()) but we don't know if the timer_bh is running - * on the other CPU, so we need a lock. We also need to lock the vsyscall - * variables, because both do_timer() and us change them -arca+vojtech - */ - - write_seqlock(&xtime_lock); - -/* - * Do the timer stuff. - */ - - do_timer(1); -#ifndef CONFIG_SMP - update_process_times(user_mode(get_irq_regs())); -#endif - -/* - * In the SMP case we use the local APIC timer interrupt to do the profiling, - * except when we simulate SMP mode on a uniprocessor system, in that case we - * have to call the local interrupt handler. - */ - - if (!using_apic_timer) - smp_local_timer_interrupt(); - -/* - * If we have an externally synchronized Linux clock, then update CMOS clock - * accordingly every ~11 minutes. set_rtc_mmss() will be called in the jiffy - * closest to exactly 500 ms before the next second. If the update fails, we - * don't care, as it'll be updated on the next turn, and the problem (time way - * off) isn't likely to go away much sooner anyway. - */ - - if (ntp_synced() && xtime.tv_sec > rtc_update && - abs(xtime.tv_nsec - 500000000) <= tick_nsec / 2) { - set_rtc_mmss(xtime.tv_sec); - rtc_update = xtime.tv_sec + 660; - } - - write_sequnlock(&xtime_lock); + return set_rtc_mmss(now.tv_sec); } static irqreturn_t timer_interrupt(int irq, void *dev_id) { - if (apic_runs_main_timer > 1) - return IRQ_HANDLED; - main_timer_handler(); - if (using_apic_timer) - smp_send_timer_broadcast_ipi(); + global_clock_event->event_handler(global_clock_event); + return IRQ_HANDLED; } -static unsigned long get_cmos_time(void) +unsigned long read_persistent_clock(void) { unsigned int year, mon, day, hour, min, sec; unsigned long flags; @@ -226,7 +183,7 @@ static unsigned long get_cmos_time(void) /* * We know that x86-64 always uses BCD format, no need to check the * config register. - */ + */ BCD_TO_BIN(sec); BCD_TO_BIN(min); @@ -239,11 +196,11 @@ static unsigned long get_cmos_time(void) BCD_TO_BIN(century); year += century * 100; printk(KERN_INFO "Extended CMOS year: %d\n", century * 100); - } else { + } else { /* * x86-64 systems only exists since 2002. * This will work up to Dec 31, 2100 - */ + */ year += 2000; } @@ -261,17 +218,17 @@ static unsigned int __init tsc_calibrate unsigned long flags; for (i = 0; i < 4; i++) - if (avail_to_resrv_perfctr_nmi_bit(i)) - break; + if (avail_to_resrv_perfctr_nmi_bit(i)) + break; no_ctr_free = (i == 4); if (no_ctr_free) { - i = 3; - rdmsrl(MSR_K7_EVNTSEL3, evntsel3); - wrmsrl(MSR_K7_EVNTSEL3, 0); - rdmsrl(MSR_K7_PERFCTR3, pmc3); + i = 3; + rdmsrl(MSR_K7_EVNTSEL3, evntsel3); + wrmsrl(MSR_K7_EVNTSEL3, 0); + rdmsrl(MSR_K7_PERFCTR3, pmc3); } else { - reserve_perfctr_nmi(MSR_K7_PERFCTR0 + i); - reserve_evntsel_nmi(MSR_K7_EVNTSEL0 + i); + reserve_perfctr_nmi(MSR_K7_PERFCTR0 + i); + reserve_evntsel_nmi(MSR_K7_EVNTSEL0 + i); } local_irq_save(flags); /* start meauring cycles, incrementing from 0 */ @@ -279,119 +236,39 @@ static unsigned int __init tsc_calibrate wrmsrl(MSR_K7_EVNTSEL0 + i, 1 << 22 | 3 << 16 | 0x76); rdtscl(tsc_start); do { - rdmsrl(MSR_K7_PERFCTR0 + i, pmc_now); - tsc_now = get_cycles_sync(); + rdmsrl(MSR_K7_PERFCTR0 + i, pmc_now); + tsc_now = get_cycles_sync(); } while ((tsc_now - tsc_start) < TICK_COUNT); local_irq_restore(flags); if (no_ctr_free) { - wrmsrl(MSR_K7_EVNTSEL3, 0); - wrmsrl(MSR_K7_PERFCTR3, pmc3); - wrmsrl(MSR_K7_EVNTSEL3, evntsel3); + wrmsrl(MSR_K7_EVNTSEL3, 0); + wrmsrl(MSR_K7_PERFCTR3, pmc3); + wrmsrl(MSR_K7_EVNTSEL3, evntsel3); } else { - release_perfctr_nmi(MSR_K7_PERFCTR0 + i); - release_evntsel_nmi(MSR_K7_EVNTSEL0 + i); + release_perfctr_nmi(MSR_K7_PERFCTR0 + i); + release_evntsel_nmi(MSR_K7_EVNTSEL0 + i); } return pmc_now * tsc_khz / (tsc_now - tsc_start); } -/* - * pit_calibrate_tsc() uses the speaker output (channel 2) of - * the PIT. This is better than using the timer interrupt output, - * because we can read the value of the speaker with just one inb(), - * where we need three i/o operations for the interrupt channel. - * We count how many ticks the TSC does in 50 ms. - */ - -static unsigned int __init pit_calibrate_tsc(void) -{ - unsigned long start, end; - unsigned long flags; - - spin_lock_irqsave(&i8253_lock, flags); - - outb((inb(0x61) & ~0x02) | 0x01, 0x61); - - outb(0xb0, 0x43); - outb((PIT_TICK_RATE / (1000 / 50)) & 0xff, 0x42); - outb((PIT_TICK_RATE / (1000 / 50)) >> 8, 0x42); - start = get_cycles_sync(); - while ((inb(0x61) & 0x20) == 0); - end = get_cycles_sync(); - - spin_unlock_irqrestore(&i8253_lock, flags); - - return (end - start) / 50; -} - -#define PIT_MODE 0x43 -#define PIT_CH0 0x40 - -static void __pit_init(int val, u8 mode) -{ - unsigned long flags; - - spin_lock_irqsave(&i8253_lock, flags); - outb_p(mode, PIT_MODE); - outb_p(val & 0xff, PIT_CH0); /* LSB */ - outb_p(val >> 8, PIT_CH0); /* MSB */ - spin_unlock_irqrestore(&i8253_lock, flags); -} - -void __init pit_init(void) -{ - __pit_init(LATCH, 0x34); /* binary, mode 2, LSB/MSB, ch 0 */ -} - -void pit_stop_interrupt(void) -{ - __pit_init(0, 0x30); /* mode 0 */ -} - -void stop_timer_interrupt(void) -{ - char *name; - if (hpet_address) { - name = "HPET"; - hpet_timer_stop_set_go(0); - } else { - name = "PIT"; - pit_stop_interrupt(); - } - printk(KERN_INFO "timer: %s interrupt stopped.\n", name); -} - static struct irqaction irq0 = { .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_IRQPOLL, + .flags = IRQF_DISABLED | IRQF_IRQPOLL | IRQF_NOBALANCING | + IRQF_NODELAY, .mask = CPU_MASK_NONE, - .name = "timer" + .name = "timer" }; void __init time_init(void) { - if (nohpet) - hpet_address = 0; - xtime.tv_sec = get_cmos_time(); - xtime.tv_nsec = 0; - - set_normalized_timespec(&wall_to_monotonic, - -xtime.tv_sec, -xtime.tv_nsec); - - if (hpet_arch_init()) - hpet_address = 0; - - if (hpet_use_timer) { - /* set tick_nsec to use the proper rate for HPET */ - tick_nsec = TICK_NSEC_HPET; - tsc_khz = hpet_calibrate_tsc(); - timename = "HPET"; - } else { - pit_init(); - tsc_khz = pit_calibrate_tsc(); - timename = "PIT"; - } + if (!hpet_enable()) + setup_pit_timer(); + + setup_irq(0, &irq0); + + tsc_calibrate(); cpu_khz = tsc_khz; if (cpu_has(&boot_cpu_data, X86_FEATURE_CONSTANT_TSC) && @@ -411,79 +288,4 @@ void __init time_init(void) printk(KERN_INFO "time.c: Detected %d.%03d MHz processor.\n", cpu_khz / 1000, cpu_khz % 1000); init_tsc_clocksource(); - - setup_irq(0, &irq0); -} - - -static long clock_cmos_diff; -static unsigned long sleep_start; - -/* - * sysfs support for the timer. - */ - -static int timer_suspend(struct sys_device *dev, pm_message_t state) -{ - /* - * Estimate time zone so that set_time can update the clock - */ - long cmos_time = get_cmos_time(); - - clock_cmos_diff = -cmos_time; - clock_cmos_diff += get_seconds(); - sleep_start = cmos_time; - return 0; } - -static int timer_resume(struct sys_device *dev) -{ - unsigned long flags; - unsigned long sec; - unsigned long ctime = get_cmos_time(); - long sleep_length = (ctime - sleep_start) * HZ; - - if (sleep_length < 0) { - printk(KERN_WARNING "Time skew detected in timer resume!\n"); - /* The time after the resume must not be earlier than the time - * before the suspend or some nasty things will happen - */ - sleep_length = 0; - ctime = sleep_start; - } - if (hpet_address) - hpet_reenable(); - else - i8254_timer_resume(); - - sec = ctime + clock_cmos_diff; - write_seqlock_irqsave(&xtime_lock,flags); - xtime.tv_sec = sec; - xtime.tv_nsec = 0; - jiffies += sleep_length; - write_sequnlock_irqrestore(&xtime_lock,flags); - touch_softlockup_watchdog(); - return 0; -} - -static struct sysdev_class timer_sysclass = { - .resume = timer_resume, - .suspend = timer_suspend, - set_kset_name("timer"), -}; - -/* XXX this sysfs stuff should probably go elsewhere later -john */ -static struct sys_device device_timer = { - .id = 0, - .cls = &timer_sysclass, -}; - -static int time_init_device(void) -{ - int error = sysdev_class_register(&timer_sysclass); - if (!error) - error = sysdev_register(&device_timer); - return error; -} - -device_initcall(time_init_device); Index: linux/arch/x86_64/kernel/traps.c =================================================================== --- linux.orig/arch/x86_64/kernel/traps.c +++ linux/arch/x86_64/kernel/traps.c @@ -215,7 +215,7 @@ void dump_trace(struct task_struct *tsk, unsigned long *stack, struct stacktrace_ops *ops, void *data) { - const unsigned cpu = get_cpu(); + const unsigned cpu = raw_smp_processor_id(); unsigned long *irqstack_end = (unsigned long*)cpu_pda(cpu)->irqstackptr; unsigned used = 0; struct thread_info *tinfo; @@ -306,7 +306,6 @@ void dump_trace(struct task_struct *tsk, tinfo = task_thread_info(tsk); HANDLE_STACK (valid_stack_ptr(tinfo, stack)); #undef HANDLE_STACK - put_cpu(); } EXPORT_SYMBOL(dump_trace); @@ -343,9 +342,13 @@ static struct stacktrace_ops print_trace void show_trace(struct task_struct *tsk, struct pt_regs *regs, unsigned long *stack) { + pause_on_oops_head(); printk("\nCall Trace:\n"); dump_trace(tsk, regs, stack, &print_trace_ops, NULL); printk("\n"); + pause_on_oops_tail(); + debug_show_held_locks(tsk); + print_traces(tsk); } static void @@ -353,7 +356,7 @@ _show_stack(struct task_struct *tsk, str { unsigned long *stack; int i; - const int cpu = smp_processor_id(); + const int cpu = raw_smp_processor_id(); unsigned long *irqstack_end = (unsigned long *) (cpu_pda(cpu)->irqstackptr); unsigned long *irqstack = (unsigned long *) (cpu_pda(cpu)->irqstackptr - IRQSTACKSIZE); Index: linux/arch/x86_64/kernel/tsc.c =================================================================== --- linux.orig/arch/x86_64/kernel/tsc.c +++ linux/arch/x86_64/kernel/tsc.c @@ -6,7 +6,9 @@ #include #include #include +#include +#include #include static int notsc __initdata = 0; @@ -61,25 +63,9 @@ static inline int check_tsc_unstable(voi * first tick after the change will be slightly wrong. */ -#include - -static unsigned int cpufreq_delayed_issched = 0; -static unsigned int cpufreq_init = 0; -static struct work_struct cpufreq_delayed_get_work; - -static void handle_cpufreq_delayed_get(struct work_struct *v) -{ - unsigned int cpu; - for_each_online_cpu(cpu) { - cpufreq_get(cpu); - } - cpufreq_delayed_issched = 0; -} - -static unsigned int ref_freq = 0; -static unsigned long loops_per_jiffy_ref = 0; - -static unsigned long tsc_khz_ref = 0; +static unsigned int ref_freq; +static unsigned long loops_per_jiffy_ref; +static unsigned long tsc_khz_ref; static int time_cpufreq_notifier(struct notifier_block *nb, unsigned long val, void *data) @@ -125,10 +111,8 @@ static struct notifier_block time_cpufre static int __init cpufreq_tsc(void) { - INIT_WORK(&cpufreq_delayed_get_work, handle_cpufreq_delayed_get); - if (!cpufreq_register_notifier(&time_cpufreq_notifier_block, - CPUFREQ_TRANSITION_NOTIFIER)) - cpufreq_init = 1; + cpufreq_register_notifier(&time_cpufreq_notifier_block, + CPUFREQ_TRANSITION_NOTIFIER); return 0; } @@ -136,7 +120,93 @@ core_initcall(cpufreq_tsc); #endif -static int tsc_unstable = 0; +#define MAX_RETRIES 5 +#define SMI_TRESHOLD 50000 + +/* + * Read TSC and the reference counters. Take care of SMI disturbance + */ +static unsigned long __init tsc_read_refs(unsigned long *pm, + unsigned long *hpet) +{ + unsigned long t1, t2; + int i; + + for (i = 0; i < MAX_RETRIES; i++) { + t1 = get_cycles_sync(); + if (hpet) + *hpet = hpet_readl(HPET_COUNTER) & 0xFFFFFFFF; + else + *pm = acpi_pm_read_early(); + t2 = get_cycles_sync(); + if ((t2 - t1) < SMI_TRESHOLD) + return t2; + } + return ULONG_MAX; +} + +/** + * tsc_calibrate - calibrate the tsc on boot + */ +void __init tsc_calibrate(void) +{ + unsigned long flags, tsc1, tsc2, tr1, tr2, pm1, pm2, hpet1, hpet2; + int hpet = is_hpet_enabled(); + + local_irq_save(flags); + + tsc1 = tsc_read_refs(&pm1, hpet ? &hpet1 : NULL); + + outb((inb(0x61) & ~0x02) | 0x01, 0x61); + + outb(0xb0, 0x43); + outb((CLOCK_TICK_RATE / (1000 / 50)) & 0xff, 0x42); + outb((CLOCK_TICK_RATE / (1000 / 50)) >> 8, 0x42); + tr1 = get_cycles_sync(); + while ((inb(0x61) & 0x20) == 0); + tr2 = get_cycles_sync(); + + tsc2 = tsc_read_refs(&pm2, hpet ? &hpet2 : NULL); + + local_irq_restore(flags); + + /* + * Preset the result with the raw and inaccurate PIT + * calibration value + */ + tsc_khz = (tr2 - tr1) / 50; + + /* hpet or pmtimer available ? */ + if (!hpet && !pm1 && !pm2) { + printk(KERN_INFO "TSC calibrated against PIT\n"); + return; + } + + /* Check, whether the sampling was disturbed by an SMI */ + if (tsc1 == ULONG_MAX || tsc2 == ULONG_MAX) { + printk(KERN_WARNING "TSC calibration disturbed by SMI, " + "using PIT calibration result\n"); + return; + } + + tsc2 = (tsc2 - tsc1) * 1000000L; + + if (hpet) { + printk(KERN_INFO "TSC calibrated against HPET\n"); + if (hpet2 < hpet1) + hpet2 += 0x100000000; + hpet2 -= hpet1; + tsc1 = (hpet2 * hpet_readl(HPET_PERIOD)) / 1000000; + } else { + printk(KERN_INFO "TSC calibrated against PM_TIMER\n"); + if (pm2 < pm1) + pm2 += ACPI_PM_OVRRUN; + pm2 -= pm1; + tsc1 = (pm2 * 1000000000) / PMTMR_TICKS_PER_SEC; + } + + tsc_khz = tsc2 / tsc1; +} /* * Make an educated guess if the TSC is trustworthy and synchronized @@ -153,17 +223,18 @@ __cpuinit int unsynchronized_tsc(void) #endif /* Most intel systems have synchronized TSCs except for multi node systems */ - if (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) { + if (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) { #ifdef CONFIG_ACPI /* But TSC doesn't tick in C3 so don't use it there */ - if (acpi_gbl_FADT.header.length > 0 && acpi_gbl_FADT.C3latency < 1000) + if (acpi_gbl_FADT.header.length > 0 && + acpi_gbl_FADT.C3latency < 1000) return 1; #endif - return 0; + return 0; } - /* Assume multi socket systems are not synchronized */ - return num_present_cpus() > 1; + /* Assume multi socket systems are not synchronized */ + return num_present_cpus() > 1; } int __init notsc_setup(char *s) @@ -176,13 +247,13 @@ __setup("notsc", notsc_setup); /* clock source code: */ -static cycle_t read_tsc(void) +static notrace cycle_t read_tsc(void) { cycle_t ret = (cycle_t)get_cycles_sync(); return ret; } -static cycle_t __vsyscall_fn vread_tsc(void) +static notrace cycle_t __vsyscall_fn vread_tsc(void) { cycle_t ret = (cycle_t)get_cycles_sync(); return ret; @@ -216,8 +287,9 @@ EXPORT_SYMBOL_GPL(mark_tsc_unstable); void __init init_tsc_clocksource(void) { if (!notsc) { - clocksource_tsc.mult = clocksource_khz2mult(tsc_khz, - clocksource_tsc.shift); + clocksource_tsc.mult = + clocksource_khz2mult(tsc_khz, clocksource_tsc.shift); + if (check_tsc_unstable()) clocksource_tsc.rating = 0; Index: linux/arch/x86_64/kernel/tsc_sync.c =================================================================== --- linux.orig/arch/x86_64/kernel/tsc_sync.c +++ linux/arch/x86_64/kernel/tsc_sync.c @@ -33,7 +33,7 @@ static __cpuinitdata atomic_t stop_count * we want to have the fastest, inlined, non-debug version * of a critical section, to be able to prove TSC time-warps: */ -static __cpuinitdata raw_spinlock_t sync_lock = __RAW_SPIN_LOCK_UNLOCKED; +static __cpuinitdata __raw_spinlock_t sync_lock = __RAW_SPIN_LOCK_UNLOCKED; static __cpuinitdata cycles_t last_tsc; static __cpuinitdata cycles_t max_warp; static __cpuinitdata int nr_warps; @@ -97,6 +97,7 @@ static __cpuinit void check_tsc_warp(voi */ void __cpuinit check_tsc_sync_source(int cpu) { + unsigned long flags; int cpus = 2; /* @@ -117,8 +118,11 @@ void __cpuinit check_tsc_sync_source(int /* * Wait for the target to arrive: */ + local_save_flags(flags); + local_irq_enable(); while (atomic_read(&start_count) != cpus-1) cpu_relax(); + local_irq_restore(flags); /* * Trigger the target to continue into the measurement too: */ Index: linux/arch/x86_64/kernel/vsyscall.c =================================================================== --- linux.orig/arch/x86_64/kernel/vsyscall.c +++ linux/arch/x86_64/kernel/vsyscall.c @@ -43,7 +43,7 @@ #include #include -#define __vsyscall(nr) __attribute__ ((unused,__section__(".vsyscall_" #nr))) +#define __vsyscall(nr) __attribute__ ((unused,__section__(".vsyscall_" #nr))) notrace #define __syscall_clobber "r11","rcx","memory" #define __pa_vsymbol(x) \ ({unsigned long v; \ @@ -58,7 +58,7 @@ * Try to keep this structure as small as possible to avoid cache line ping pongs */ struct vsyscall_gtod_data_t { - seqlock_t lock; + raw_seqlock_t lock; /* open coded 'struct timespec' */ time_t wall_time_sec; @@ -68,7 +68,7 @@ struct vsyscall_gtod_data_t { struct timezone sys_tz; struct { /* extract of a clocksource struct */ cycle_t (*vread)(void); - cycle_t cycle_last; + cycle_t cycle_last, cycle_accumulated; cycle_t mask; u32 mult; u32 shift; @@ -78,7 +78,7 @@ int __vgetcpu_mode __section_vgetcpu_mod struct vsyscall_gtod_data_t __vsyscall_gtod_data __section_vsyscall_gtod_data = { - .lock = SEQLOCK_UNLOCKED, + .lock = __RAW_SEQLOCK_UNLOCKED(__vsyscall_gtod_data.lock), .sysctl_enabled = 1, }; @@ -128,10 +128,29 @@ static __always_inline long time_syscall static __always_inline void do_vgettimeofday(struct timeval * tv) { - cycle_t now, base, mask, cycle_delta; + cycle_t now, base, accumulated, mask, cycle_delta; unsigned seq; unsigned long mult, shift, nsec; cycle_t (*vread)(void); + + if (likely(__vsyscall_gtod_data.sysctl_enabled == 2)) { + struct timeval tmp; + + do { + barrier(); + tv->tv_sec = __vsyscall_gtod_data.wall_time_sec; + tv->tv_usec = __vsyscall_gtod_data.wall_time_nsec; + barrier(); + tmp.tv_sec = __vsyscall_gtod_data.wall_time_sec; + tmp.tv_usec = __vsyscall_gtod_data.wall_time_nsec; + + } while (tmp.tv_usec != tv->tv_usec || + tmp.tv_sec != tv->tv_sec); + + tv->tv_usec /= NSEC_PER_USEC; + return; + } + do { seq = read_seqbegin(&__vsyscall_gtod_data.lock); @@ -142,6 +161,7 @@ static __always_inline void do_vgettimeo } now = vread(); base = __vsyscall_gtod_data.clock.cycle_last; + accumulated = __vsyscall_gtod_data.clock.cycle_accumulated; mask = __vsyscall_gtod_data.clock.mask; mult = __vsyscall_gtod_data.clock.mult; shift = __vsyscall_gtod_data.clock.shift; @@ -152,6 +172,7 @@ static __always_inline void do_vgettimeo /* calculate interval: */ cycle_delta = (now - base) & mask; + cycle_delta += accumulated; /* convert to nsecs: */ nsec += (cycle_delta * mult) >> shift; Index: linux/arch/x86_64/kernel/x8664_ksyms.c =================================================================== --- linux.orig/arch/x86_64/kernel/x8664_ksyms.c +++ linux/arch/x86_64/kernel/x8664_ksyms.c @@ -11,10 +11,12 @@ EXPORT_SYMBOL(kernel_thread); -EXPORT_SYMBOL(__down_failed); -EXPORT_SYMBOL(__down_failed_interruptible); -EXPORT_SYMBOL(__down_failed_trylock); -EXPORT_SYMBOL(__up_wakeup); +#ifdef CONFIG_RWSEM_GENERIC_SPINLOCK +EXPORT_SYMBOL(__compat_down_failed); +EXPORT_SYMBOL(__compat_down_failed_interruptible); +EXPORT_SYMBOL(__compat_down_failed_trylock); +EXPORT_SYMBOL(__compat_up_wakeup); +#endif EXPORT_SYMBOL(__get_user_1); EXPORT_SYMBOL(__get_user_2); Index: linux/arch/x86_64/lib/thunk.S =================================================================== --- linux.orig/arch/x86_64/lib/thunk.S +++ linux/arch/x86_64/lib/thunk.S @@ -40,15 +40,31 @@ thunk rwsem_wake_thunk,rwsem_wake thunk rwsem_downgrade_thunk,rwsem_downgrade_wake #endif - - thunk __down_failed,__down - thunk_retrax __down_failed_interruptible,__down_interruptible - thunk_retrax __down_failed_trylock,__down_trylock - thunk __up_wakeup,__up + +#ifdef CONFIG_RWSEM_GENERIC_SPINLOCK + thunk __compat_down_failed,__compat_down + thunk_retrax __compat_down_failed_interruptible,__compat_down_interruptible + thunk_retrax __compat_down_failed_trylock,__compat_down_trylock + thunk __compat_up_wakeup,__compat_up +#endif #ifdef CONFIG_TRACE_IRQFLAGS - thunk trace_hardirqs_on_thunk,trace_hardirqs_on - thunk trace_hardirqs_off_thunk,trace_hardirqs_off + /* put return address in rdi (arg1) */ + .macro thunk_ra name,func + .globl \name +\name: + CFI_STARTPROC + SAVE_ARGS + /* SAVE_ARGS pushs 9 elements */ + /* the next element would be the rip */ + movq 9*8(%rsp), %rdi + call \func + jmp restore + CFI_ENDPROC + .endm + + thunk_ra trace_hardirqs_on_thunk,trace_hardirqs_on_caller + thunk_ra trace_hardirqs_off_thunk,trace_hardirqs_off_caller #endif /* SAVE_ARGS below is used only for the .cfi directives it contains. */ Index: linux/arch/x86_64/mm/fault.c =================================================================== --- linux.orig/arch/x86_64/mm/fault.c +++ linux/arch/x86_64/mm/fault.c @@ -381,7 +381,7 @@ asmlinkage void __kprobes do_page_fault( * If we're in an interrupt or have no user * context, we must not take the fault.. */ - if (unlikely(in_atomic() || !mm)) + if (unlikely(in_atomic() || !mm || current->pagefault_disabled)) goto bad_area_nosemaphore; again: Index: linux/arch/x86_64/mm/init.c =================================================================== --- linux.orig/arch/x86_64/mm/init.c +++ linux/arch/x86_64/mm/init.c @@ -53,7 +53,7 @@ EXPORT_SYMBOL(dma_ops); static unsigned long dma_reserve __initdata; -DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); +DEFINE_PER_CPU_LOCKED(struct mmu_gather, mmu_gathers); /* * NOTE: pagetable_init alloc all the fixmap pagetables contiguous on the Index: linux/block/cfq-iosched.c =================================================================== --- linux.orig/block/cfq-iosched.c +++ linux/block/cfq-iosched.c @@ -1278,6 +1278,8 @@ static void cfq_init_prio_data(struct cf /* * no prio set, place us in the middle of the BE classes */ + if (tsk->policy == SCHED_IDLE) + goto set_class_idle; cfqq->ioprio = task_nice_ioprio(tsk); cfqq->ioprio_class = IOPRIO_CLASS_BE; break; @@ -1290,6 +1292,7 @@ static void cfq_init_prio_data(struct cf cfqq->ioprio_class = IOPRIO_CLASS_BE; break; case IOPRIO_CLASS_IDLE: + set_class_idle: cfqq->ioprio_class = IOPRIO_CLASS_IDLE; cfqq->ioprio = 7; cfq_clear_cfqq_idle_window(cfqq); Index: linux/block/ll_rw_blk.c =================================================================== --- linux.orig/block/ll_rw_blk.c +++ linux/block/ll_rw_blk.c @@ -1549,7 +1549,7 @@ static int ll_merge_requests_fn(request_ */ void blk_plug_device(request_queue_t *q) { - WARN_ON(!irqs_disabled()); + WARN_ON_NONRT(!irqs_disabled()); /* * don't plug a stopped queue, it must be paired with blk_start_queue() @@ -1572,7 +1572,7 @@ EXPORT_SYMBOL(blk_plug_device); */ int blk_remove_plug(request_queue_t *q) { - WARN_ON(!irqs_disabled()); + WARN_ON_NONRT(!irqs_disabled()); if (!test_and_clear_bit(QUEUE_FLAG_PLUGGED, &q->queue_flags)) return 0; @@ -1664,7 +1664,7 @@ static void blk_unplug_timeout(unsigned **/ void blk_start_queue(request_queue_t *q) { - WARN_ON(!irqs_disabled()); + WARN_ON_NONRT(!irqs_disabled()); clear_bit(QUEUE_FLAG_STOPPED, &q->queue_flags); Index: linux/drivers/Makefile =================================================================== --- linux.orig/drivers/Makefile +++ linux/drivers/Makefile @@ -70,6 +70,7 @@ obj-$(CONFIG_EDAC) += edac/ obj-$(CONFIG_MCA) += mca/ obj-$(CONFIG_EISA) += eisa/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ +obj-$(CONFIG_CPU_IDLE) += cpuidle/ obj-$(CONFIG_MMC) += mmc/ obj-$(CONFIG_NEW_LEDS) += leds/ obj-$(CONFIG_INFINIBAND) += infiniband/ Index: linux/drivers/acpi/ec.c =================================================================== --- linux.orig/drivers/acpi/ec.c +++ linux/drivers/acpi/ec.c @@ -420,7 +420,19 @@ static u32 acpi_ec_gpe_handler(void *dat atomic_inc(&ec->event_count); if (acpi_ec_mode == EC_INTR) { +#if 0 wake_up(&ec->wait); +#else + // hack ... + if (waitqueue_active(&ec->wait)) { + struct task_struct *task; + + task = list_entry(ec->wait.task_list.next, + wait_queue_t, task_list)->private; + if (task) + wake_up_process(task); + } +#endif } value = acpi_ec_read_status(ec); Index: linux/drivers/acpi/hardware/hwregs.c =================================================================== --- linux.orig/drivers/acpi/hardware/hwregs.c +++ linux/drivers/acpi/hardware/hwregs.c @@ -73,7 +73,7 @@ acpi_status acpi_hw_clear_acpi_status(vo ACPI_BITMASK_ALL_FIXED_STATUS, (u16) acpi_gbl_FADT.xpm1a_event_block.address)); - lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock); + spin_lock_irqsave(acpi_gbl_hardware_lock, lock_flags); status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1_STATUS, @@ -98,7 +98,7 @@ acpi_status acpi_hw_clear_acpi_status(vo status = acpi_ev_walk_gpe_list(acpi_hw_clear_gpe_block); unlock_and_exit: - acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags); + spin_unlock_irqrestore(acpi_gbl_hardware_lock, lock_flags); return_ACPI_STATUS(status); } @@ -331,7 +331,7 @@ acpi_status acpi_set_register(u32 regist return_ACPI_STATUS(AE_BAD_PARAMETER); } - lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock); + spin_lock_irqsave(acpi_gbl_hardware_lock, lock_flags); /* Always do a register read first so we can insert the new bits */ @@ -441,7 +441,7 @@ acpi_status acpi_set_register(u32 regist unlock_and_exit: - acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags); + spin_unlock_irqrestore(acpi_gbl_hardware_lock, lock_flags); /* Normalize the value that was read */ @@ -481,7 +481,7 @@ acpi_hw_register_read(u8 use_lock, u32 r ACPI_FUNCTION_TRACE(hw_register_read); if (ACPI_MTX_LOCK == use_lock) { - lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock); + spin_lock_irqsave(acpi_gbl_hardware_lock, lock_flags); } switch (register_id) { @@ -560,7 +560,7 @@ acpi_hw_register_read(u8 use_lock, u32 r unlock_and_exit: if (ACPI_MTX_LOCK == use_lock) { - acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags); + spin_unlock_irqrestore(acpi_gbl_hardware_lock, lock_flags); } if (ACPI_SUCCESS(status)) { @@ -606,7 +606,7 @@ acpi_status acpi_hw_register_write(u8 us ACPI_FUNCTION_TRACE(hw_register_write); if (ACPI_MTX_LOCK == use_lock) { - lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock); + spin_lock_irqsave(acpi_gbl_hardware_lock, lock_flags); } switch (register_id) { @@ -730,7 +730,7 @@ acpi_status acpi_hw_register_write(u8 us unlock_and_exit: if (ACPI_MTX_LOCK == use_lock) { - acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags); + spin_unlock_irqrestore(acpi_gbl_hardware_lock, lock_flags); } return_ACPI_STATUS(status); Index: linux/drivers/acpi/osl.c =================================================================== --- linux.orig/drivers/acpi/osl.c +++ linux/drivers/acpi/osl.c @@ -745,13 +745,13 @@ void acpi_os_delete_lock(acpi_spinlock h acpi_status acpi_os_create_semaphore(u32 max_units, u32 initial_units, acpi_handle * handle) { - struct semaphore *sem = NULL; + struct compat_semaphore *sem = NULL; - sem = acpi_os_allocate(sizeof(struct semaphore)); + sem = acpi_os_allocate(sizeof(struct compat_semaphore)); if (!sem) return AE_NO_MEMORY; - memset(sem, 0, sizeof(struct semaphore)); + memset(sem, 0, sizeof(struct compat_semaphore)); sema_init(sem, initial_units); @@ -774,7 +774,7 @@ EXPORT_SYMBOL(acpi_os_create_semaphore); acpi_status acpi_os_delete_semaphore(acpi_handle handle) { - struct semaphore *sem = (struct semaphore *)handle; + struct compat_semaphore *sem = (struct compat_semaphore *)handle; if (!sem) @@ -802,7 +802,7 @@ EXPORT_SYMBOL(acpi_os_delete_semaphore); acpi_status acpi_os_wait_semaphore(acpi_handle handle, u32 units, u16 timeout) { acpi_status status = AE_OK; - struct semaphore *sem = (struct semaphore *)handle; + struct compat_semaphore *sem = (struct compat_semaphore *)handle; int ret = 0; @@ -889,7 +889,7 @@ EXPORT_SYMBOL(acpi_os_wait_semaphore); */ acpi_status acpi_os_signal_semaphore(acpi_handle handle, u32 units) { - struct semaphore *sem = (struct semaphore *)handle; + struct compat_semaphore *sem = (struct compat_semaphore *)handle; if (!sem || (units < 1)) @@ -1056,6 +1056,17 @@ unsigned int max_cstate = ACPI_PROCESSOR EXPORT_SYMBOL(max_cstate); +void (*acpi_do_set_cstate_limit)(void); +EXPORT_SYMBOL(acpi_do_set_cstate_limit); + +void acpi_set_cstate_limit(unsigned int new_limit) +{ + max_cstate = new_limit; + if (acpi_do_set_cstate_limit) + acpi_do_set_cstate_limit(); +} +EXPORT_SYMBOL(acpi_set_cstate_limit); + /* * Acquire a spinlock. * Index: linux/drivers/acpi/processor_core.c =================================================================== --- linux.orig/drivers/acpi/processor_core.c +++ linux/drivers/acpi/processor_core.c @@ -44,6 +44,7 @@ #include #include #include +#include #include #include @@ -1022,11 +1023,15 @@ static int __init acpi_processor_init(vo acpi_processor_ppc_init(); + cpuidle_register_driver(&acpi_idle_driver); + acpi_do_set_cstate_limit = acpi_max_cstate_changed; return 0; } static void __exit acpi_processor_exit(void) { + acpi_do_set_cstate_limit = NULL; + cpuidle_unregister_driver(&acpi_idle_driver); acpi_processor_ppc_exit(); Index: linux/drivers/acpi/processor_idle.c =================================================================== --- linux.orig/drivers/acpi/processor_idle.c +++ linux/drivers/acpi/processor_idle.c @@ -40,6 +40,7 @@ #include /* need_resched() */ #include #include +#include /* * Include the apic definitions for x86 to have the APIC timer related defines @@ -62,25 +63,34 @@ #define _COMPONENT ACPI_PROCESSOR_COMPONENT ACPI_MODULE_NAME("processor_idle"); #define ACPI_PROCESSOR_FILE_POWER "power" -#define US_TO_PM_TIMER_TICKS(t) ((t * (PM_TIMER_FREQUENCY/1000)) / 1000) -#define C2_OVERHEAD 4 /* 1us (3.579 ticks per us) */ -#define C3_OVERHEAD 4 /* 1us (3.579 ticks per us) */ -static void (*pm_idle_save) (void) __read_mostly; -module_param(max_cstate, uint, 0644); +#define PM_TIMER_TICKS_TO_US(p) (((p) * 1000)/(PM_TIMER_FREQUENCY/1000)) +#define C2_OVERHEAD 1 /* 1us */ +#define C3_OVERHEAD 1 /* 1us */ + +void acpi_max_cstate_changed(void) +{ + /* Driver will reset devices' max cstate limit */ + cpuidle_force_redetect_devices(&acpi_idle_driver); +} + +static int change_max_cstate(const char *val, struct kernel_param *kp) +{ + int max; + + max = simple_strtol(val, NULL, 0); + if (!max) + return -EINVAL; + max_cstate = max; + if (acpi_do_set_cstate_limit) + acpi_do_set_cstate_limit(); + return 0; +} + +module_param_call(max_cstate, change_max_cstate, param_get_uint, &max_cstate, 0644); static unsigned int nocst __read_mostly; module_param(nocst, uint, 0000); -/* - * bm_history -- bit-mask with a bit per jiffy of bus-master activity - * 1000 HZ: 0xFFFFFFFF: 32 jiffies = 32ms - * 800 HZ: 0xFFFFFFFF: 32 jiffies = 40ms - * 100 HZ: 0x0000000F: 4 jiffies = 40ms - * reduce history for more aggressive entry into C3 - */ -static unsigned int bm_history __read_mostly = - (HZ >= 800 ? 0xFFFFFFFF : ((1U << (HZ / 25)) - 1)); -module_param(bm_history, uint, 0644); /* -------------------------------------------------------------------------- Power Management -------------------------------------------------------------------------- */ @@ -166,88 +176,6 @@ static struct dmi_system_id __cpuinitdat {}, }; -static inline u32 ticks_elapsed(u32 t1, u32 t2) -{ - if (t2 >= t1) - return (t2 - t1); - else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER)) - return (((0x00FFFFFF - t1) + t2) & 0x00FFFFFF); - else - return ((0xFFFFFFFF - t1) + t2); -} - -static void -acpi_processor_power_activate(struct acpi_processor *pr, - struct acpi_processor_cx *new) -{ - struct acpi_processor_cx *old; - - if (!pr || !new) - return; - - old = pr->power.state; - - if (old) - old->promotion.count = 0; - new->demotion.count = 0; - - /* Cleanup from old state. */ - if (old) { - switch (old->type) { - case ACPI_STATE_C3: - /* Disable bus master reload */ - if (new->type != ACPI_STATE_C3 && pr->flags.bm_check) - acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 0); - break; - } - } - - /* Prepare to use new state. */ - switch (new->type) { - case ACPI_STATE_C3: - /* Enable bus master reload */ - if (old->type != ACPI_STATE_C3 && pr->flags.bm_check) - acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 1); - break; - } - - pr->power.state = new; - - return; -} - -static void acpi_safe_halt(void) -{ - current_thread_info()->status &= ~TS_POLLING; - /* - * TS_POLLING-cleared state must be visible before we - * test NEED_RESCHED: - */ - smp_mb(); - if (!need_resched()) - safe_halt(); - current_thread_info()->status |= TS_POLLING; -} - -static atomic_t c3_cpu_count; - -/* Common C-state entry for C2, C3, .. */ -static void acpi_cstate_enter(struct acpi_processor_cx *cstate) -{ - if (cstate->space_id == ACPI_CSTATE_FFH) { - /* Call into architectural FFH based C-state */ - acpi_processor_ffh_cstate_enter(cstate); - } else { - int unused; - /* IO port based C-state */ - inb(cstate->address); - /* Dummy wait op - must do something useless after P_LVL2 read - because chipsets cannot guarantee that STPCLK# signal - gets asserted in time to freeze execution properly. */ - unused = inl(acpi_gbl_FADT.xpm_timer_block.address); - } -} - #ifdef ARCH_APICTIMER_STOPS_ON_C3 /* @@ -275,21 +203,12 @@ static void acpi_timer_check_state(int s static void acpi_propagate_timer_broadcast(struct acpi_processor *pr) { -#ifdef CONFIG_GENERIC_CLOCKEVENTS unsigned long reason; reason = pr->power.timer_broadcast_on_state < INT_MAX ? CLOCK_EVT_NOTIFY_BROADCAST_ON : CLOCK_EVT_NOTIFY_BROADCAST_OFF; clockevents_notify(reason, &pr->id); -#else - cpumask_t mask = cpumask_of_cpu(pr->id); - - if (pr->power.timer_broadcast_on_state < INT_MAX) - on_each_cpu(switch_APIC_timer_to_ipi, &mask, 1, 1); - else - on_each_cpu(switch_ipi_to_APIC_timer, &mask, 1, 1); -#endif } /* Power(C) State timer broadcast control */ @@ -297,8 +216,6 @@ static void acpi_state_timer_broadcast(s struct acpi_processor_cx *cx, int broadcast) { -#ifdef CONFIG_GENERIC_CLOCKEVENTS - int state = cx - pr->power.states; if (state >= pr->power.timer_broadcast_on_state) { @@ -308,7 +225,6 @@ static void acpi_state_timer_broadcast(s CLOCK_EVT_NOTIFY_BROADCAST_EXIT; clockevents_notify(reason, &pr->id); } -#endif } #else @@ -323,378 +239,6 @@ static void acpi_state_timer_broadcast(s } #endif - -static void acpi_processor_idle(void) -{ - struct acpi_processor *pr = NULL; - struct acpi_processor_cx *cx = NULL; - struct acpi_processor_cx *next_state = NULL; - int sleep_ticks = 0; - u32 t1, t2 = 0; - - /* - * Interrupts must be disabled during bus mastering calculations and - * for C2/C3 transitions. - */ - local_irq_disable(); - - pr = processors[smp_processor_id()]; - if (!pr) { - local_irq_enable(); - return; - } - - /* - * Check whether we truly need to go idle, or should - * reschedule: - */ - if (unlikely(need_resched())) { - local_irq_enable(); - return; - } - - cx = pr->power.state; - if (!cx) { - if (pm_idle_save) - pm_idle_save(); - else - acpi_safe_halt(); - return; - } - - /* - * Check BM Activity - * ----------------- - * Check for bus mastering activity (if required), record, and check - * for demotion. - */ - if (pr->flags.bm_check) { - u32 bm_status = 0; - unsigned long diff = jiffies - pr->power.bm_check_timestamp; - - if (diff > 31) - diff = 31; - - pr->power.bm_activity <<= diff; - - acpi_get_register(ACPI_BITREG_BUS_MASTER_STATUS, &bm_status); - if (bm_status) { - pr->power.bm_activity |= 0x1; - acpi_set_register(ACPI_BITREG_BUS_MASTER_STATUS, 1); - } - /* - * PIIX4 Erratum #18: Note that BM_STS doesn't always reflect - * the true state of bus mastering activity; forcing us to - * manually check the BMIDEA bit of each IDE channel. - */ - else if (errata.piix4.bmisx) { - if ((inb_p(errata.piix4.bmisx + 0x02) & 0x01) - || (inb_p(errata.piix4.bmisx + 0x0A) & 0x01)) - pr->power.bm_activity |= 0x1; - } - - pr->power.bm_check_timestamp = jiffies; - - /* - * If bus mastering is or was active this jiffy, demote - * to avoid a faulty transition. Note that the processor - * won't enter a low-power state during this call (to this - * function) but should upon the next. - * - * TBD: A better policy might be to fallback to the demotion - * state (use it for this quantum only) istead of - * demoting -- and rely on duration as our sole demotion - * qualification. This may, however, introduce DMA - * issues (e.g. floppy DMA transfer overrun/underrun). - */ - if ((pr->power.bm_activity & 0x1) && - cx->demotion.threshold.bm) { - local_irq_enable(); - next_state = cx->demotion.state; - goto end; - } - } - -#ifdef CONFIG_HOTPLUG_CPU - /* - * Check for P_LVL2_UP flag before entering C2 and above on - * an SMP system. We do it here instead of doing it at _CST/P_LVL - * detection phase, to work cleanly with logical CPU hotplug. - */ - if ((cx->type != ACPI_STATE_C1) && (num_online_cpus() > 1) && - !pr->flags.has_cst && !(acpi_gbl_FADT.flags & ACPI_FADT_C2_MP_SUPPORTED)) - cx = &pr->power.states[ACPI_STATE_C1]; -#endif - - /* - * Sleep: - * ------ - * Invoke the current Cx state to put the processor to sleep. - */ - if (cx->type == ACPI_STATE_C2 || cx->type == ACPI_STATE_C3) { - current_thread_info()->status &= ~TS_POLLING; - /* - * TS_POLLING-cleared state must be visible before we - * test NEED_RESCHED: - */ - smp_mb(); - if (need_resched()) { - current_thread_info()->status |= TS_POLLING; - local_irq_enable(); - return; - } - } - - switch (cx->type) { - - case ACPI_STATE_C1: - /* - * Invoke C1. - * Use the appropriate idle routine, the one that would - * be used without acpi C-states. - */ - if (pm_idle_save) - pm_idle_save(); - else - acpi_safe_halt(); - - /* - * TBD: Can't get time duration while in C1, as resumes - * go to an ISR rather than here. Need to instrument - * base interrupt handler. - */ - sleep_ticks = 0xFFFFFFFF; - break; - - case ACPI_STATE_C2: - /* Get start time (ticks) */ - t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); - /* Invoke C2 */ - acpi_state_timer_broadcast(pr, cx, 1); - acpi_cstate_enter(cx); - /* Get end time (ticks) */ - t2 = inl(acpi_gbl_FADT.xpm_timer_block.address); - -#ifdef CONFIG_GENERIC_TIME - /* TSC halts in C2, so notify users */ - mark_tsc_unstable("possible TSC halt in C2"); -#endif - /* Re-enable interrupts */ - local_irq_enable(); - current_thread_info()->status |= TS_POLLING; - /* Compute time (ticks) that we were actually asleep */ - sleep_ticks = - ticks_elapsed(t1, t2) - cx->latency_ticks - C2_OVERHEAD; - acpi_state_timer_broadcast(pr, cx, 0); - break; - - case ACPI_STATE_C3: - - if (pr->flags.bm_check) { - if (atomic_inc_return(&c3_cpu_count) == - num_online_cpus()) { - /* - * All CPUs are trying to go to C3 - * Disable bus master arbitration - */ - acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1); - } - } else { - /* SMP with no shared cache... Invalidate cache */ - ACPI_FLUSH_CPU_CACHE(); - } - - /* Get start time (ticks) */ - t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); - /* Invoke C3 */ - acpi_state_timer_broadcast(pr, cx, 1); - acpi_cstate_enter(cx); - /* Get end time (ticks) */ - t2 = inl(acpi_gbl_FADT.xpm_timer_block.address); - if (pr->flags.bm_check) { - /* Enable bus master arbitration */ - atomic_dec(&c3_cpu_count); - acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0); - } - -#ifdef CONFIG_GENERIC_TIME - /* TSC halts in C3, so notify users */ - mark_tsc_unstable("TSC halts in C3"); -#endif - /* Re-enable interrupts */ - local_irq_enable(); - current_thread_info()->status |= TS_POLLING; - /* Compute time (ticks) that we were actually asleep */ - sleep_ticks = - ticks_elapsed(t1, t2) - cx->latency_ticks - C3_OVERHEAD; - acpi_state_timer_broadcast(pr, cx, 0); - break; - - default: - local_irq_enable(); - return; - } - cx->usage++; - if ((cx->type != ACPI_STATE_C1) && (sleep_ticks > 0)) - cx->time += sleep_ticks; - - next_state = pr->power.state; - -#ifdef CONFIG_HOTPLUG_CPU - /* Don't do promotion/demotion */ - if ((cx->type == ACPI_STATE_C1) && (num_online_cpus() > 1) && - !pr->flags.has_cst && !(acpi_gbl_FADT.flags & ACPI_FADT_C2_MP_SUPPORTED)) { - next_state = cx; - goto end; - } -#endif - - /* - * Promotion? - * ---------- - * Track the number of longs (time asleep is greater than threshold) - * and promote when the count threshold is reached. Note that bus - * mastering activity may prevent promotions. - * Do not promote above max_cstate. - */ - if (cx->promotion.state && - ((cx->promotion.state - pr->power.states) <= max_cstate)) { - if (sleep_ticks > cx->promotion.threshold.ticks && - cx->promotion.state->latency <= system_latency_constraint()) { - cx->promotion.count++; - cx->demotion.count = 0; - if (cx->promotion.count >= - cx->promotion.threshold.count) { - if (pr->flags.bm_check) { - if (! - (pr->power.bm_activity & cx-> - promotion.threshold.bm)) { - next_state = - cx->promotion.state; - goto end; - } - } else { - next_state = cx->promotion.state; - goto end; - } - } - } - } - - /* - * Demotion? - * --------- - * Track the number of shorts (time asleep is less than time threshold) - * and demote when the usage threshold is reached. - */ - if (cx->demotion.state) { - if (sleep_ticks < cx->demotion.threshold.ticks) { - cx->demotion.count++; - cx->promotion.count = 0; - if (cx->demotion.count >= cx->demotion.threshold.count) { - next_state = cx->demotion.state; - goto end; - } - } - } - - end: - /* - * Demote if current state exceeds max_cstate - * or if the latency of the current state is unacceptable - */ - if ((pr->power.state - pr->power.states) > max_cstate || - pr->power.state->latency > system_latency_constraint()) { - if (cx->demotion.state) - next_state = cx->demotion.state; - } - - /* - * New Cx State? - * ------------- - * If we're going to start using a new Cx state we must clean up - * from the previous and prepare to use the new. - */ - if (next_state != pr->power.state) - acpi_processor_power_activate(pr, next_state); -} - -static int acpi_processor_set_power_policy(struct acpi_processor *pr) -{ - unsigned int i; - unsigned int state_is_set = 0; - struct acpi_processor_cx *lower = NULL; - struct acpi_processor_cx *higher = NULL; - struct acpi_processor_cx *cx; - - - if (!pr) - return -EINVAL; - - /* - * This function sets the default Cx state policy (OS idle handler). - * Our scheme is to promote quickly to C2 but more conservatively - * to C3. We're favoring C2 for its characteristics of low latency - * (quick response), good power savings, and ability to allow bus - * mastering activity. Note that the Cx state policy is completely - * customizable and can be altered dynamically. - */ - - /* startup state */ - for (i = 1; i < ACPI_PROCESSOR_MAX_POWER; i++) { - cx = &pr->power.states[i]; - if (!cx->valid) - continue; - - if (!state_is_set) - pr->power.state = cx; - state_is_set++; - break; - } - - if (!state_is_set) - return -ENODEV; - - /* demotion */ - for (i = 1; i < ACPI_PROCESSOR_MAX_POWER; i++) { - cx = &pr->power.states[i]; - if (!cx->valid) - continue; - - if (lower) { - cx->demotion.state = lower; - cx->demotion.threshold.ticks = cx->latency_ticks; - cx->demotion.threshold.count = 1; - if (cx->type == ACPI_STATE_C3) - cx->demotion.threshold.bm = bm_history; - } - - lower = cx; - } - - /* promotion */ - for (i = (ACPI_PROCESSOR_MAX_POWER - 1); i > 0; i--) { - cx = &pr->power.states[i]; - if (!cx->valid) - continue; - - if (higher) { - cx->promotion.state = higher; - cx->promotion.threshold.ticks = cx->latency_ticks; - if (cx->type >= ACPI_STATE_C2) - cx->promotion.threshold.count = 4; - else - cx->promotion.threshold.count = 10; - if (higher->type == ACPI_STATE_C3) - cx->promotion.threshold.bm = bm_history; - } - - higher = cx; - } - - return 0; -} - static int acpi_processor_get_power_info_fadt(struct acpi_processor *pr) { @@ -912,7 +456,7 @@ static void acpi_processor_power_verify_ * Normalize the C2 latency to expidite policy */ cx->valid = 1; - cx->latency_ticks = US_TO_PM_TIMER_TICKS(cx->latency); + cx->latency_ticks = cx->latency; return; } @@ -986,7 +530,7 @@ static void acpi_processor_power_verify_ * use this in our C3 policy */ cx->valid = 1; - cx->latency_ticks = US_TO_PM_TIMER_TICKS(cx->latency); + cx->latency_ticks = cx->latency; return; } @@ -1052,18 +596,6 @@ static int acpi_processor_get_power_info pr->power.count = acpi_processor_power_verify(pr); /* - * Set Default Policy - * ------------------ - * Now that we know which states are supported, set the default - * policy. Note that this policy can be changed dynamically - * (e.g. encourage deeper sleeps to conserve battery life when - * not on AC). - */ - result = acpi_processor_set_power_policy(pr); - if (result) - return result; - - /* * if one state of type C2 or C3 is available, mark this * CPU as being "idle manageable" */ @@ -1080,9 +612,6 @@ static int acpi_processor_get_power_info int acpi_processor_cst_has_changed(struct acpi_processor *pr) { - int result = 0; - - if (!pr) return -EINVAL; @@ -1093,16 +622,9 @@ int acpi_processor_cst_has_changed(struc if (!pr->flags.power_setup_done) return -ENODEV; - /* Fall back to the default idle loop */ - pm_idle = pm_idle_save; - synchronize_sched(); /* Relies on interrupts forcing exit from idle. */ - - pr->flags.power = 0; - result = acpi_processor_get_power_info(pr); - if ((pr->flags.power == 1) && (pr->flags.power_setup_done)) - pm_idle = acpi_processor_idle; - - return result; + acpi_processor_get_power_info(pr); + return cpuidle_force_redetect(per_cpu(cpuidle_devices, pr->id), + &acpi_idle_driver); } /* proc interface */ @@ -1188,30 +710,6 @@ static const struct file_operations acpi .release = single_release, }; -#ifdef CONFIG_SMP -static void smp_callback(void *v) -{ - /* we already woke the CPU up, nothing more to do */ -} - -/* - * This function gets called when a part of the kernel has a new latency - * requirement. This means we need to get all processors out of their C-state, - * and then recalculate a new suitable C-state. Just do a cross-cpu IPI; that - * wakes them all right up. - */ -static int acpi_processor_latency_notify(struct notifier_block *b, - unsigned long l, void *v) -{ - smp_call_function(smp_callback, NULL, 0, 1); - return NOTIFY_OK; -} - -static struct notifier_block acpi_processor_latency_notifier = { - .notifier_call = acpi_processor_latency_notify, -}; -#endif - int __cpuinit acpi_processor_power_init(struct acpi_processor *pr, struct acpi_device *device) { @@ -1228,9 +726,6 @@ int __cpuinit acpi_processor_power_init( "ACPI: processor limited to max C-state %d\n", max_cstate); first_run++; -#ifdef CONFIG_SMP - register_latency_notifier(&acpi_processor_latency_notifier); -#endif } if (!pr) @@ -1247,6 +742,7 @@ int __cpuinit acpi_processor_power_init( acpi_processor_get_power_info(pr); + /* * Install the idle handler if processor power management is supported. * Note that we use previously set idle handler will be used on @@ -1259,11 +755,6 @@ int __cpuinit acpi_processor_power_init( printk(" C%d[C%d]", i, pr->power.states[i].type); printk(")\n"); - - if (pr->id == 0) { - pm_idle_save = pm_idle; - pm_idle = acpi_processor_idle; - } } /* 'power' [R] */ @@ -1291,21 +782,357 @@ int acpi_processor_power_exit(struct acp if (acpi_device_dir(device)) remove_proc_entry(ACPI_PROCESSOR_FILE_POWER, acpi_device_dir(device)); + return 0; +} - /* Unregister the idle handler when processor #0 is removed. */ - if (pr->id == 0) { - pm_idle = pm_idle_save; +/** + * ticks_elapsed - a helper function that determines how many ticks (in US) + * have elapsed between two PM Timer timestamps + * @t1: the start time + * @t2: the end time + */ +static inline u32 ticks_elapsed_in_us(u32 t1, u32 t2) +{ + if (t2 >= t1) + return PM_TIMER_TICKS_TO_US(t2 - t1); + else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER)) + return PM_TIMER_TICKS_TO_US(((0x00FFFFFF - t1) + t2) & 0x00FFFFFF); + else + return PM_TIMER_TICKS_TO_US((0xFFFFFFFF - t1) + t2); +} - /* - * We are about to unload the current idle thread pm callback - * (pm_idle), Wait for all processors to update cached/local - * copies of pm_idle before proceeding. - */ - cpu_idle_wait(); -#ifdef CONFIG_SMP - unregister_latency_notifier(&acpi_processor_latency_notifier); +static inline u32 ticks_elapsed(u32 t1, u32 t2) +{ + if (t2 >= t1) + return (t2 - t1); + else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER)) + return (((0x00FFFFFF - t1) + t2) & 0x00FFFFFF); + else + return ((0xFFFFFFFF - t1) + t2); +} + +/** + * acpi_idle_update_bm_rld - updates the BM_RLD bit depending on target state + * @pr: the processor + * @target: the new target state + */ +static inline void acpi_idle_update_bm_rld(struct acpi_processor *pr, + struct acpi_processor_cx *target) +{ + if (pr->flags.bm_rld_set && target->type != ACPI_STATE_C3) { + acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 0); + pr->flags.bm_rld_set = 0; + } + + if (!pr->flags.bm_rld_set && target->type == ACPI_STATE_C3) { + acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 1); + pr->flags.bm_rld_set = 1; + } +} + +/** + * acpi_idle_do_entry - a helper function that does C2 and C3 type entry + * @cx: cstate data + */ +static inline void acpi_idle_do_entry(struct acpi_processor_cx *cx) +{ + /* + * We have irqs disabled here, so stop latency tracing + * at this point and restart it after we return: + */ + stop_critical_timing(); + + if (cx->space_id == ACPI_CSTATE_FFH) { + /* Call into architectural FFH based C-state */ + acpi_processor_ffh_cstate_enter(cx); + } else { + int unused; + /* IO port based C-state */ + inb(cx->address); + /* Dummy wait op - must do something useless after P_LVL2 read + because chipsets cannot guarantee that STPCLK# signal + gets asserted in time to freeze execution properly. */ + unused = inl(acpi_gbl_FADT.xpm_timer_block.address); + } + + touch_critical_timing(); +} + +/** + * acpi_idle_enter_c1 - enters an ACPI C1 state-type + * @dev: the target CPU + * @state: the state data + * + * This is equivalent to the HALT instruction. + */ +static int acpi_idle_enter_c1(struct cpuidle_device *dev, + struct cpuidle_state *state) +{ + struct acpi_processor *pr; + struct acpi_processor_cx *cx = cpuidle_get_statedata(state); + pr = processors[smp_processor_id()]; + + if (unlikely(!pr)) + return 0; + + if (pr->flags.bm_check) + acpi_idle_update_bm_rld(pr, cx); + + current_thread_info()->status &= ~TS_POLLING; + /* + * TS_POLLING-cleared state must be visible before we test + * NEED_RESCHED: + */ + smp_mb(); + if (!need_resched() || !need_resched_delayed()) + safe_halt(); + current_thread_info()->status |= TS_POLLING; + + cx->usage++; + + return 0; +} + +/** + * acpi_idle_enter_c2 - enters an ACPI C2 state-type + * @dev: the target CPU + * @state: the state data + */ +static int acpi_idle_enter_c2(struct cpuidle_device *dev, + struct cpuidle_state *state) +{ + struct acpi_processor *pr; + struct acpi_processor_cx *cx = cpuidle_get_statedata(state); + u32 t1, t2; + pr = processors[smp_processor_id()]; + + if (unlikely(!pr)) + return 0; + + if (pr->flags.bm_check) + acpi_idle_update_bm_rld(pr, cx); + + local_irq_disable(); + current_thread_info()->status &= ~TS_POLLING; + /* + * TS_POLLING-cleared state must be visible before we test + * NEED_RESCHED: + */ + smp_mb(); + + if (unlikely(need_resched() || need_resched_delayed())) { + current_thread_info()->status |= TS_POLLING; + local_irq_enable(); + return 0; + } + + t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); + acpi_state_timer_broadcast(pr, cx, 1); + acpi_idle_do_entry(cx); + t2 = inl(acpi_gbl_FADT.xpm_timer_block.address); + +#ifdef CONFIG_GENERIC_TIME + /* TSC halts in C2, so notify users */ + mark_tsc_unstable("possible TSC halt in C2"); #endif + + local_irq_enable(); + current_thread_info()->status |= TS_POLLING; + + cx->usage++; + + acpi_state_timer_broadcast(pr, cx, 0); + cx->time += ticks_elapsed(t1, t2); + return ticks_elapsed_in_us(t1, t2); +} + +static int c3_cpu_count; +static DEFINE_SPINLOCK(c3_lock); + +/** + * acpi_idle_enter_c3 - enters an ACPI C3 state-type + * @dev: the target CPU + * @state: the state data + * + * Similar to C2 entry, except special bus master handling is needed. + */ +static int acpi_idle_enter_c3(struct cpuidle_device *dev, + struct cpuidle_state *state) +{ + struct acpi_processor *pr; + struct acpi_processor_cx *cx = cpuidle_get_statedata(state); + u32 t1, t2; + pr = processors[smp_processor_id()]; + + if (unlikely(!pr)) + return 0; + + if (pr->flags.bm_check) + acpi_idle_update_bm_rld(pr, cx); + + local_irq_disable(); + current_thread_info()->status &= ~TS_POLLING; + /* + * TS_POLLING-cleared state must be visible before we test + * NEED_RESCHED: + */ + smp_mb(); + + if (unlikely(need_resched() || need_resched_delayed())) { + current_thread_info()->status |= TS_POLLING; + local_irq_enable(); + return 0; + } + + /* + * Must be done before busmaster disable as we might need to + * access HPET ! + */ + acpi_state_timer_broadcast(pr, cx, 1); + + /* disable bus master */ + if (pr->flags.bm_check) { + spin_lock(&c3_lock); + c3_cpu_count++; + if (c3_cpu_count == num_online_cpus()) { + /* + * All CPUs are trying to go to C3 + * Disable bus master arbitration + */ + acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1); + } + spin_unlock(&c3_lock); + } else { + /* SMP with no shared cache... Invalidate cache */ + ACPI_FLUSH_CPU_CACHE(); } + /* Get start time (ticks) */ + t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); + acpi_idle_do_entry(cx); + t2 = inl(acpi_gbl_FADT.xpm_timer_block.address); + + if (pr->flags.bm_check) { + spin_lock(&c3_lock); + /* Enable bus master arbitration */ + if (c3_cpu_count == num_online_cpus()) + acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0); + c3_cpu_count--; + spin_unlock(&c3_lock); + } + +#ifdef CONFIG_GENERIC_TIME + /* TSC halts in C3, so notify users */ + mark_tsc_unstable("TSC halts in C3"); +#endif + + local_irq_enable(); + current_thread_info()->status |= TS_POLLING; + + cx->usage++; + + acpi_state_timer_broadcast(pr, cx, 0); + cx->time += ticks_elapsed(t1, t2); + return ticks_elapsed_in_us(t1, t2); +} + +/** + * acpi_idle_bm_check - checks if bus master activity was detected + */ +static int acpi_idle_bm_check(void) +{ + u32 bm_status = 0; + + acpi_get_register(ACPI_BITREG_BUS_MASTER_STATUS, &bm_status); + if (bm_status) + acpi_set_register(ACPI_BITREG_BUS_MASTER_STATUS, 1); + /* + * PIIX4 Erratum #18: Note that BM_STS doesn't always reflect + * the true state of bus mastering activity; forcing us to + * manually check the BMIDEA bit of each IDE channel. + */ + else if (errata.piix4.bmisx) { + if ((inb_p(errata.piix4.bmisx + 0x02) & 0x01) + || (inb_p(errata.piix4.bmisx + 0x0A) & 0x01)) + bm_status = 1; + } + return bm_status; +} + +/** + * acpi_idle_init - attaches the driver to a CPU + * @dev: the CPU + */ +static int acpi_idle_init(struct cpuidle_device *dev) +{ + int cpu = dev->cpu; + int i, count = 0; + struct acpi_processor_cx *cx; + struct cpuidle_state *state; + + struct acpi_processor *pr = processors[cpu]; + + if (!pr->flags.power_setup_done) + return -EINVAL; + + if (pr->flags.power == 0) { + return -EINVAL; + } + + for (i = 1; i < ACPI_PROCESSOR_MAX_POWER && i <= max_cstate; i++) { + cx = &pr->power.states[i]; + state = &dev->states[count]; + + if (!cx->valid) + continue; + +#ifdef CONFIG_HOTPLUG_CPU + if ((cx->type != ACPI_STATE_C1) && (num_online_cpus() > 1) && + !pr->flags.has_cst && + !(acpi_gbl_FADT.flags & ACPI_FADT_C2_MP_SUPPORTED)) + continue; +#endif + cpuidle_set_statedata(state, cx); + + state->exit_latency = cx->latency; + state->target_residency = cx->latency * 6; + state->power_usage = cx->power; + + state->flags = 0; + switch (cx->type) { + case ACPI_STATE_C1: + state->flags |= CPUIDLE_FLAG_SHALLOW; + state->enter = acpi_idle_enter_c1; + break; + + case ACPI_STATE_C2: + state->flags |= CPUIDLE_FLAG_BALANCED; + state->flags |= CPUIDLE_FLAG_TIME_VALID; + state->enter = acpi_idle_enter_c2; + break; + + case ACPI_STATE_C3: + state->flags |= CPUIDLE_FLAG_DEEP; + state->flags |= CPUIDLE_FLAG_TIME_VALID; + state->flags |= CPUIDLE_FLAG_CHECK_BM; + state->enter = acpi_idle_enter_c3; + break; + } + + count++; + } + + if (!count) + return -EINVAL; + + dev->state_count = count; return 0; } + +struct cpuidle_driver acpi_idle_driver = { + .name = "acpi_idle", + .init = acpi_idle_init, + .redetect = acpi_idle_init, + .bm_check = acpi_idle_bm_check, + .owner = THIS_MODULE, +}; Index: linux/drivers/acpi/utilities/utmutex.c =================================================================== --- linux.orig/drivers/acpi/utilities/utmutex.c +++ linux/drivers/acpi/utilities/utmutex.c @@ -116,7 +116,7 @@ void acpi_ut_mutex_terminate(void) /* Delete the spinlocks */ acpi_os_delete_lock(acpi_gbl_gpe_lock); - acpi_os_delete_lock(acpi_gbl_hardware_lock); +// acpi_os_delete_lock(acpi_gbl_hardware_lock); return_VOID; } Index: linux/drivers/base/power/resume.c =================================================================== --- linux.orig/drivers/base/power/resume.c +++ linux/drivers/base/power/resume.c @@ -9,6 +9,7 @@ */ #include +#include #include #include "../base.h" #include "power.h" Index: linux/drivers/block/floppy.c =================================================================== --- linux.orig/drivers/block/floppy.c +++ linux/drivers/block/floppy.c @@ -4157,6 +4157,28 @@ static void floppy_device_release(struct complete(&device_release); } +static int floppy_suspend(struct platform_device *dev, pm_message_t state) +{ + floppy_release_irq_and_dma(); + + return 0; +} + +static int floppy_resume(struct platform_device *dev) +{ + floppy_grab_irq_and_dma(); + + return 0; +} + +static struct platform_driver floppy_driver = { + .suspend = floppy_suspend, + .resume = floppy_resume, + .driver = { + .name = "floppy", + }, +}; + static struct platform_device floppy_device[N_DRIVE]; static struct kobject *floppy_find(dev_t dev, int *part, void *data) @@ -4205,10 +4227,14 @@ static int __init floppy_init(void) if (err) goto out_put_disk; + err = platform_driver_register(&floppy_driver); + if (err) + goto out_unreg_blkdev; + floppy_queue = blk_init_queue(do_fd_request, &floppy_lock); if (!floppy_queue) { err = -ENOMEM; - goto out_unreg_blkdev; + goto out_unreg_driver; } blk_queue_max_sectors(floppy_queue, 64); @@ -4357,6 +4383,8 @@ out_flush_work: out_unreg_region: blk_unregister_region(MKDEV(FLOPPY_MAJOR, 0), 256); blk_cleanup_queue(floppy_queue); +out_unreg_driver: + platform_driver_unregister(&floppy_driver); out_unreg_blkdev: unregister_blkdev(FLOPPY_MAJOR, "fd"); out_put_disk: @@ -4548,6 +4576,7 @@ void cleanup_module(void) init_completion(&device_release); blk_unregister_region(MKDEV(FLOPPY_MAJOR, 0), 256); unregister_blkdev(FLOPPY_MAJOR, "fd"); + platform_driver_unregister(&floppy_driver); for (drive = 0; drive < N_DRIVE; drive++) { del_timer_sync(&motor_off_timer[drive]); Index: linux/drivers/block/paride/pseudo.h =================================================================== --- linux.orig/drivers/block/paride/pseudo.h +++ linux/drivers/block/paride/pseudo.h @@ -43,7 +43,7 @@ static unsigned long ps_timeout; static int ps_tq_active = 0; static int ps_nice = 0; -static DEFINE_SPINLOCK(ps_spinlock __attribute__((unused))); +static __attribute__((unused)) DEFINE_SPINLOCK(ps_spinlock); static DECLARE_DELAYED_WORK(ps_tq, ps_tq_int); Index: linux/drivers/cdrom/sjcd.c =================================================================== --- linux.orig/drivers/cdrom/sjcd.c +++ linux/drivers/cdrom/sjcd.c @@ -69,6 +69,7 @@ #include #include #include +#include #include #include @@ -1709,12 +1710,11 @@ static int __init sjcd_init(void) printk(KERN_INFO "SJCD: Resetting: "); sjcd_send_cmd(SCMD_RESET); for (i = 1000; i > 0 && !sjcd_status_valid; --i) { - unsigned long timer; - /* * Wait 10ms approx. */ - for (timer = jiffies; time_before_eq(jiffies, timer);); + msleep(10); + if ((i % 100) == 0) printk("."); (void) sjcd_check_status(); Index: linux/drivers/char/Kconfig =================================================================== --- linux.orig/drivers/char/Kconfig +++ linux/drivers/char/Kconfig @@ -791,6 +791,46 @@ config RTC To compile this driver as a module, choose M here: the module will be called rtc. +config RTC_HISTOGRAM + bool "Real Time Clock Histogram Support" + default n + depends on RTC + ---help--- + If you say Y here then the kernel will track the delivery and + wakeup latency of /dev/rtc using tasks and will report a + histogram to the kernel log when the application closes /dev/rtc. + +config BLOCKER + tristate "Priority Inheritance Debugging (Blocker) Device Support" + depends on X86 + default y + ---help--- + If you say Y here then a device will be created that the userspace + pi_test suite uses to test and measure kernel locking primitives. + +config LPPTEST + tristate "Parallel Port Based Latency Measurement Device" + depends on !PARPORT && X86 + default y + ---help--- + If you say Y here then a device will be created that the userspace + testlpp utility uses to measure IRQ latencies of a target system + from an independent measurement system. + + NOTE: this code assumes x86 PCs and that the parallel port is + bidirectional and is on IRQ 7. + + to use the device, both the target and the source system needs to + run a kernel with CONFIG_LPPTEST enabled. To measure latencies, + use the scripts/testlpp utility in your kernel source directory, + and run it (as root) on the source system - it will start printing + out the latencies it took to get a response from the target system: + + Latency of response: 12.2 usecs (121265 cycles) + + then generate various workloads on the target system to see how + (worst-case-) latencies are impacted. + config SGI_DS1286 tristate "SGI DS1286 RTC support" depends on SGI_IP22 @@ -1075,6 +1115,24 @@ config TELCLOCK /sys/devices/platform/telco_clock, with a number of files for controlling the behavior of this hardware. +config RMEM + tristate "Access to physical memory via /dev/rmem" + default m + help + The /dev/mem device only allows mmap() memory available to + I/O mapped memory; it does not allow access to "real" + physical memory. The /dev/rmem device is a hack which does + allow access to physical memory. We use this instead of + patching /dev/mem because we don't expect this functionality + to ever be accepted into mainline. + +config ALLOC_RTSJ_MEM + tristate "RTSJ-specific hack to reserve memory" + default m + help + The RTSJ TCK conformance test requires reserving some physical + memory for testing /dev/rmem. + config DEVPORT bool depends on !M68K Index: linux/drivers/char/Makefile =================================================================== --- linux.orig/drivers/char/Makefile +++ linux/drivers/char/Makefile @@ -94,6 +94,10 @@ obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu. obj-$(CONFIG_GPIO_TB0219) += tb0219.o obj-$(CONFIG_TELCLOCK) += tlclk.o +obj-$(CONFIG_BLOCKER) += blocker.o +obj-$(CONFIG_LPPTEST) += lpptest.o +obj-$(CONFIG_RMEM) += rmem.o + obj-$(CONFIG_WATCHDOG) += watchdog/ obj-$(CONFIG_MWAVE) += mwave/ obj-$(CONFIG_AGP) += agp/ @@ -104,6 +108,8 @@ obj-$(CONFIG_IPMI_HANDLER) += ipmi/ obj-$(CONFIG_HANGCHECK_TIMER) += hangcheck-timer.o obj-$(CONFIG_TCG_TPM) += tpm/ +obj-$(CONFIG_ALLOC_RTSJ_MEM) += alloc_rtsj_mem.o + # Files generated that shall be removed upon make clean clean-files := consolemap_deftbl.c defkeymap.c Index: linux/drivers/char/alloc_rtsj_mem.c =================================================================== --- /dev/null +++ linux/drivers/char/alloc_rtsj_mem.c @@ -0,0 +1,88 @@ +/* + * alloc_rtsj_mem.c -- Hack to allocate some memory + * + * Copyright (C) 2005 by Theodore Ts'o + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#include +#include +#include +#include +#include + +#include + +MODULE_AUTHOR("Theodore Tso"); +MODULE_DESCRIPTION("RTSJ alloc memory"); +MODULE_LICENSE("GPL"); + +static void *mem = 0; +int size = 0, addr = 0; + +module_param(size, int, 0444); +module_param(addr, int, 0444); + +static void __exit shutdown_module(void) +{ + kfree(mem); +} + +#ifndef MODULE +void __init alloc_rtsj_mem_early_setup(void) +{ + if (size > PAGE_SIZE*2) { + mem = alloc_bootmem(size); + if (mem) { + printk(KERN_INFO "alloc_rtsj_mem: got %d bytes " + "using alloc_bootmem\n", size); + } else { + printk(KERN_INFO "alloc_rtsj_mem: failed to " + "get %d bytes from alloc_bootmem\n", size); + } + } +} +#endif + +static int __init startup_module(void) +{ + static char test_string[] = "The BOFH: Servicing users the way the " + "military\n\tservices targets for 15 years.\n"; + + if (!size) + return 0; + + if (!mem) { + mem = kmalloc(size, GFP_KERNEL); + if (mem) { + printk(KERN_INFO "alloc_rtsj_mem: got %d bytes " + "using kmalloc\n", size); + } else { + printk(KERN_ERR "alloc_rtsj_mem: failed to get " + "%d bytes using kmalloc\n", size); + return -ENOMEM; + } + } + memcpy(mem, test_string, min(sizeof(test_string), (size_t) size)); + addr = virt_to_phys(mem); + return 0; +} + +module_init(startup_module); +module_exit(shutdown_module); + Index: linux/drivers/char/blocker.c =================================================================== --- /dev/null +++ linux/drivers/char/blocker.c @@ -0,0 +1,107 @@ +/* + * priority inheritance testing device + */ + +#include +#include + +#define BLOCKER_MINOR 221 + +#define BLOCK_IOCTL 4245 +#define BLOCK_SET_DEPTH 4246 + +#define BLOCKER_MAX_LOCK_DEPTH 10 + +void loop(int loops) +{ + int i; + + for (i = 0; i < loops; i++) + get_cycles(); +} + +static spinlock_t blocker_lock[BLOCKER_MAX_LOCK_DEPTH]; + +static unsigned int lock_depth = 1; + +void do_the_lock_and_loop(unsigned int args) +{ + int i, max; + + if (rt_task(current)) + max = lock_depth; + else if (lock_depth > 1) + max = (current->pid % lock_depth) + 1; + else + max = 1; + + /* Always lock from the top down */ + for (i = max-1; i >= 0; i--) + spin_lock(&blocker_lock[i]); + loop(args); + for (i = 0; i < max; i++) + spin_unlock(&blocker_lock[i]); +} + +static int blocker_open(struct inode *in, struct file *file) +{ + printk(KERN_INFO "blocker_open called\n"); + + return 0; +} + +static long blocker_ioctl(struct file *file, + unsigned int cmd, unsigned long args) +{ + switch(cmd) { + case BLOCK_IOCTL: + do_the_lock_and_loop(args); + return 0; + case BLOCK_SET_DEPTH: + if (args >= BLOCKER_MAX_LOCK_DEPTH) + return -EINVAL; + lock_depth = args; + return 0; + default: + return -EINVAL; + } +} + +static struct file_operations blocker_fops = { + .owner = THIS_MODULE, + .llseek = no_llseek, + .unlocked_ioctl = blocker_ioctl, + .open = blocker_open, +}; + +static struct miscdevice blocker_dev = +{ + BLOCKER_MINOR, + "blocker", + &blocker_fops +}; + +static int __init blocker_init(void) +{ + int i; + + if (misc_register(&blocker_dev)) + return -ENODEV; + + for (i = 0; i < BLOCKER_MAX_LOCK_DEPTH; i++) + spin_lock_init(blocker_lock + i); + + return 0; +} + +void __exit blocker_exit(void) +{ + printk(KERN_INFO "blocker device uninstalled\n"); + misc_deregister(&blocker_dev); +} + +module_init(blocker_init); +module_exit(blocker_exit); + +MODULE_LICENSE("GPL"); + Index: linux/drivers/char/lpptest.c =================================================================== --- /dev/null +++ linux/drivers/char/lpptest.c @@ -0,0 +1,178 @@ +/* + * /dev/lpptest device: test IRQ handling latencies over parallel port + * + * Copyright (C) 2005 Thomas Gleixner, Ingo Molnar + * + * licensed under the GPL + * + * You need to have CONFIG_PARPORT disabled for this device, it is a + * completely self-contained device that assumes sole ownership of the + * parallel port. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * API wrappers so that the code can be shared with the -rt tree: + */ +#ifndef local_irq_disable +# define local_irq_disable local_irq_disable +# define local_irq_enable local_irq_enable +#endif + +#ifndef IRQ_NODELAY +# define IRQ_NODELAY 0 +# define IRQF_NODELAY 0 +#endif + +/* + * Driver: + */ +#define LPPTEST_CHAR_MAJOR 245 +#define LPPTEST_DEVICE_NAME "lpptest" + +#define LPPTEST_IRQ 7 + +#define LPPTEST_TEST _IOR (LPPTEST_CHAR_MAJOR, 1, unsigned long long) +#define LPPTEST_DISABLE _IOR (LPPTEST_CHAR_MAJOR, 2, unsigned long long) +#define LPPTEST_ENABLE _IOR (LPPTEST_CHAR_MAJOR, 3, unsigned long long) + +static char dev_id[] = "lpptest"; + +#define INIT_PORT() outb(0x04, 0x37a) +#define ENABLE_IRQ() outb(0x10, 0x37a) +#define DISABLE_IRQ() outb(0, 0x37a) + +static unsigned char out = 0x5a; + +/** + * Interrupt handler. Flip a bit in the reply. + */ +static int lpptest_irq (int irq, void *dev_id) +{ + out ^= 0xff; + outb(out, 0x378); + + return IRQ_HANDLED; +} + +static cycles_t test_response(void) +{ + cycles_t now, end; + unsigned char in; + int timeout = 0; + + local_irq_disable(); + in = inb(0x379); + inb(0x378); + outb(0x08, 0x378); + now = get_cycles(); + while(1) { + if (inb(0x379) != in) + break; + if (timeout++ > 1000000) { + outb(0x00, 0x378); + local_irq_enable(); + + return 0; + } + } + end = get_cycles(); + outb(0x00, 0x378); + local_irq_enable(); + + return end - now; +} + +static int lpptest_open(struct inode *inode, struct file *file) +{ + return 0; +} + +static int lpptest_close(struct inode *inode, struct file *file) +{ + return 0; +} + +int lpptest_ioctl(struct inode *inode, struct file *file, unsigned int ioctl_num, unsigned long ioctl_param) +{ + int retval = 0; + + switch (ioctl_num) { + + case LPPTEST_DISABLE: + DISABLE_IRQ(); + break; + + case LPPTEST_ENABLE: + ENABLE_IRQ(); + break; + + case LPPTEST_TEST: { + + cycles_t diff = test_response(); + if (copy_to_user((void *)ioctl_param, (void*) &diff, sizeof(diff))) + goto errcpy; + break; + } + default: retval = -EINVAL; + } + + return retval; + + errcpy: + return -EFAULT; +} + +static struct file_operations lpptest_dev_fops = { + .ioctl = lpptest_ioctl, + .open = lpptest_open, + .release = lpptest_close, +}; + +static int __init lpptest_init (void) +{ + if (register_chrdev(LPPTEST_CHAR_MAJOR, LPPTEST_DEVICE_NAME, &lpptest_dev_fops)) + { + printk(KERN_NOTICE "Can't allocate major number %d for lpptest.\n", + LPPTEST_CHAR_MAJOR); + return -EAGAIN; + } + + if (request_irq (LPPTEST_IRQ, lpptest_irq, 0, "lpptest", dev_id)) { + printk (KERN_WARNING "lpptest: irq %d in use. Unload parport module!\n", LPPTEST_IRQ); + unregister_chrdev(LPPTEST_CHAR_MAJOR, LPPTEST_DEVICE_NAME); + return -EAGAIN; + } + irq_desc[LPPTEST_IRQ].status |= IRQ_NODELAY; + irq_desc[LPPTEST_IRQ].action->flags |= IRQF_NODELAY | IRQF_DISABLED; + + INIT_PORT(); + ENABLE_IRQ(); + + return 0; +} +module_init (lpptest_init); + +static void __exit lpptest_exit (void) +{ + DISABLE_IRQ(); + + free_irq(LPPTEST_IRQ, dev_id); + unregister_chrdev(LPPTEST_CHAR_MAJOR, LPPTEST_DEVICE_NAME); +} +module_exit (lpptest_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("lpp test module"); + Index: linux/drivers/char/random.c =================================================================== --- linux.orig/drivers/char/random.c +++ linux/drivers/char/random.c @@ -580,8 +580,11 @@ static void add_timer_randomness(struct preempt_disable(); /* if over the trickle threshold, use only 1 in 4096 samples */ if (input_pool.entropy_count > trickle_thresh && - (__get_cpu_var(trickle_count)++ & 0xfff)) - goto out; + (__get_cpu_var(trickle_count)++ & 0xfff)) { + preempt_enable(); + return; + } + preempt_enable(); sample.jiffies = jiffies; sample.cycles = get_cycles(); @@ -626,9 +629,6 @@ static void add_timer_randomness(struct if(input_pool.entropy_count >= random_read_wakeup_thresh) wake_up_interruptible(&random_read_wait); - -out: - preempt_enable(); } void add_input_randomness(unsigned int type, unsigned int code, Index: linux/drivers/char/rmem.c =================================================================== --- /dev/null +++ linux/drivers/char/rmem.c @@ -0,0 +1,134 @@ +/* + * Rmem - REALLY simple memory mapping demonstration. + * + * Copyright (C) 2005 by Theodore Ts'o + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +static int rmem_major = 0; +module_param(rmem_major, int, 0444); + +static struct class *rmem_class; + +MODULE_AUTHOR("Theodore Ts'o"); +MODULE_LICENSE("GPL"); + +struct page *rmem_vma_nopage(struct vm_area_struct *vma, + unsigned long address, int *type) +{ + struct page *pageptr; + unsigned long offset = vma->vm_pgoff << PAGE_SHIFT; + unsigned long physaddr = address - vma->vm_start + offset; + unsigned long pageframe = physaddr >> PAGE_SHIFT; + + if (!pfn_valid(pageframe)) + return NOPAGE_SIGBUS; + pageptr = pfn_to_page(pageframe); + get_page(pageptr); + if (type) + *type = VM_FAULT_MINOR; + return pageptr; +} + +static struct vm_operations_struct rmem_nopage_vm_ops = { + .nopage = rmem_vma_nopage, +}; + +static int rmem_nopage_mmap(struct file *filp, struct vm_area_struct *vma) +{ + unsigned long offset = vma->vm_pgoff << PAGE_SHIFT; + + if (offset >= __pa(high_memory) || (filp->f_flags & O_SYNC)) + vma->vm_flags |= VM_IO; + vma->vm_flags |= VM_RESERVED; + vma->vm_ops = &rmem_nopage_vm_ops; +#ifdef TAINT_USER + add_taint(TAINT_USER); +#endif + return 0; +} + +static struct file_operations rmem_nopage_ops = { + .owner = THIS_MODULE, + .mmap = rmem_nopage_mmap, +}; + +static struct cdev rmem_cdev = { + .kobj = {.name = "rmem", }, + .owner = THIS_MODULE, +}; + +static int __init rmem_init(void) +{ + int result; + dev_t dev = MKDEV(rmem_major, 0); + + /* Figure out our device number. */ + if (rmem_major) + result = register_chrdev_region(dev, 1, "rmem"); + else { + result = alloc_chrdev_region(&dev, 0, 1, "rmem"); + rmem_major = MAJOR(dev); + } + if (result < 0) { + printk(KERN_WARNING "rmem: unable to get major %d\n", rmem_major); + return result; + } + if (rmem_major == 0) + rmem_major = result; + + cdev_init(&rmem_cdev, &rmem_nopage_ops); + result = cdev_add(&rmem_cdev, dev, 1); + if (result) { + printk (KERN_NOTICE "Error %d adding /dev/rmem", result); + kobject_put(&rmem_cdev.kobj); + unregister_chrdev_region(dev, 1); + return 1; + } + + rmem_class = class_create(THIS_MODULE, "rmem"); + class_device_create(rmem_class, NULL, dev, NULL, "rmem"); + + return 0; +} + + +static void __exit rmem_cleanup(void) +{ + cdev_del(&rmem_cdev); + unregister_chrdev_region(MKDEV(rmem_major, 0), 1); + class_destroy(rmem_class); +} + + +module_init(rmem_init); +module_exit(rmem_cleanup); Index: linux/drivers/char/rtc.c =================================================================== --- linux.orig/drivers/char/rtc.c +++ linux/drivers/char/rtc.c @@ -82,21 +82,48 @@ #include #include -#if defined(__i386__) -#include +#if defined(__i386__) || defined(__x86_64__) +# include #endif -#ifdef __sparc__ -#include -#include -#ifdef __sparc_v9__ -#include +#ifdef CONFIG_MIPS +# include #endif +#ifdef __sparc__ + +# include +# include +# ifdef __sparc_v9__ +# include +# endif + static unsigned long rtc_port; static int rtc_irq = PCI_IRQ_NONE; #endif +#ifdef CONFIG_RTC_HISTOGRAM + +static cycles_t last_interrupt_time; + +#include + +#define CPU_MHZ (cpu_khz / 1000) + +#define HISTSIZE 10000 +static int histogram[HISTSIZE]; + +static int rtc_state; + +enum rtc_states { + S_STARTUP, /* First round - let the application start */ + S_IDLE, /* Waiting for an interrupt */ + S_WAITING_FOR_READ, /* Signal delivered. waiting for rtc_read() */ + S_READ_MISSED, /* Signal delivered, read() deadline missed */ +}; + +#endif + #ifdef CONFIG_HPET_RTC_IRQ #undef RTC_IRQ #endif @@ -225,7 +252,146 @@ static inline unsigned char rtc_is_updat return uip; } +#ifndef RTC_IRQ +# undef CONFIG_RTC_HISTOGRAM +#endif + +static inline void rtc_open_event(void) +{ +#ifdef CONFIG_RTC_HISTOGRAM + int i; + + last_interrupt_time = 0; + rtc_state = S_STARTUP; + rtc_irq_data = 0; + + for (i = 0; i < HISTSIZE; i++) + histogram[i] = 0; +#endif +} + +static inline void rtc_wake_event(void) +{ +#ifndef CONFIG_RTC_HISTOGRAM + kill_fasync (&rtc_async_queue, SIGIO, POLL_IN); +#else + if (!(rtc_status & RTC_IS_OPEN)) + return; + + switch (rtc_state) { + /* Startup */ + case S_STARTUP: + kill_fasync (&rtc_async_queue, SIGIO, POLL_IN); + break; + /* Waiting for an interrupt */ + case S_IDLE: + kill_fasync (&rtc_async_queue, SIGIO, POLL_IN); + last_interrupt_time = get_cycles(); + rtc_state = S_WAITING_FOR_READ; + break; + + /* Signal has been delivered. waiting for rtc_read() */ + case S_WAITING_FOR_READ: + /* + * Well foo. The usermode application didn't + * schedule and read in time. + */ + last_interrupt_time = get_cycles(); + rtc_state = S_READ_MISSED; + printk("Read missed before next interrupt\n"); + break; + /* Signal has been delivered, read() deadline was missed */ + case S_READ_MISSED: + /* + * Not much we can do here. We're waiting for the usermode + * application to read the rtc + */ + last_interrupt_time = get_cycles(); + break; + } +#endif +} + +static inline void rtc_read_event(void) +{ +#ifdef CONFIG_RTC_HISTOGRAM + cycles_t now = get_cycles(); + + switch (rtc_state) { + /* Startup */ + case S_STARTUP: + rtc_state = S_IDLE; + break; + + /* Waiting for an interrupt */ + case S_IDLE: + printk("bug in rtc_read(): called in state S_IDLE!\n"); + break; + case S_WAITING_FOR_READ: /* + * Signal has been delivered. + * waiting for rtc_read() + */ + /* + * Well done + */ + case S_READ_MISSED: /* + * Signal has been delivered, read() + * deadline was missed + */ + /* + * So, you finally got here. + */ + if (!last_interrupt_time) + printk("bug in rtc_read(): last_interrupt_time = 0\n"); + rtc_state = S_IDLE; + { + cycles_t latency = now - last_interrupt_time; + unsigned long delta; /* Microseconds */ + + delta = latency; + delta /= CPU_MHZ; + + if (delta > 1000 * 1000) { + printk("rtc: eek\n"); + } else { + unsigned long slot = delta; + if (slot >= HISTSIZE) + slot = HISTSIZE - 1; + histogram[slot]++; + if (delta > 2000) + printk("wow! That was a " + "%ld millisec bump\n", + delta / 1000); + } + } + rtc_state = S_IDLE; + break; + } +#endif +} + +static inline void rtc_close_event(void) +{ +#ifdef CONFIG_RTC_HISTOGRAM + int i = 0; + unsigned long total = 0; + + for (i = 0; i < HISTSIZE; i++) + total += histogram[i]; + if (!total) + return; + + printk("\nrtc latency histogram of {%s/%d, %lu samples}:\n", + current->comm, current->pid, total); + for (i = 0; i < HISTSIZE; i++) { + if (histogram[i]) + printk("%d %d\n", i, histogram[i]); + } +#endif +} + #ifdef RTC_IRQ + /* * A very tiny interrupt handler. It runs with IRQF_DISABLED set, * but there is possibility of conflicting with the set_rtc_mmss() @@ -269,9 +435,9 @@ irqreturn_t rtc_interrupt(int irq, void if (rtc_callback) rtc_callback->func(rtc_callback->private_data); spin_unlock(&rtc_task_lock); - wake_up_interruptible(&rtc_wait); - kill_fasync (&rtc_async_queue, SIGIO, POLL_IN); + rtc_wake_event(); + wake_up_interruptible(&rtc_wait); return IRQ_HANDLED; } @@ -381,6 +547,8 @@ static ssize_t rtc_read(struct file *fil schedule(); } while (1); + rtc_read_event(); + if (count == sizeof(unsigned int)) retval = put_user(data, (unsigned int __user *)buf) ?: sizeof(int); else @@ -613,6 +781,11 @@ static int rtc_do_ioctl(unsigned int cmd save_freq_select = CMOS_READ(RTC_FREQ_SELECT); CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT); + /* + * Make CMOS date writes nonpreemptible even on PREEMPT_RT. + * There's a limit to everything! =B-) + */ + preempt_disable(); #ifdef CONFIG_MACH_DECSTATION CMOS_WRITE(real_yrs, RTC_DEC_YEAR); #endif @@ -622,6 +795,7 @@ static int rtc_do_ioctl(unsigned int cmd CMOS_WRITE(hrs, RTC_HOURS); CMOS_WRITE(min, RTC_MINUTES); CMOS_WRITE(sec, RTC_SECONDS); + preempt_enable(); CMOS_WRITE(save_control, RTC_CONTROL); CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT); @@ -720,6 +894,7 @@ static int rtc_open(struct inode *inode, if(rtc_status & RTC_IS_OPEN) goto out_busy; + rtc_open_event(); rtc_status |= RTC_IS_OPEN; rtc_irq_data = 0; @@ -775,6 +950,7 @@ no_irq: rtc_irq_data = 0; rtc_status &= ~RTC_IS_OPEN; spin_unlock_irq (&rtc_lock); + rtc_close_event(); return 0; } @@ -1159,7 +1335,9 @@ static void rtc_dropped_irq(unsigned lon spin_unlock_irq(&rtc_lock); +#ifndef CONFIG_PREEMPT_RT printk(KERN_WARNING "rtc: lost some interrupts at %ldHz.\n", freq); +#endif /* Now we have new data */ wake_up_interruptible(&rtc_wait); Index: linux/drivers/char/sysrq.c =================================================================== --- linux.orig/drivers/char/sysrq.c +++ linux/drivers/char/sysrq.c @@ -208,6 +208,22 @@ static struct sysrq_key_op sysrq_showreg .enable_mask = SYSRQ_ENABLE_DUMP, }; +#if defined(__i386__) || defined(__x86_64__) + +static void sysrq_handle_showallregs(int key, struct tty_struct *tty) +{ + nmi_show_all_regs(); +} + +static struct sysrq_key_op sysrq_showallregs_op = { + .handler = sysrq_handle_showallregs, + .help_msg = "showalLcpupc", + .action_msg = "Show Regs On All CPUs", +}; +#else +#define sysrq_showallregs_op (*(struct sysrq_key_op *)0) +#endif + static void sysrq_handle_showstate(int key, struct tty_struct *tty) { show_state(); @@ -340,7 +356,7 @@ static struct sysrq_key_op *sysrq_key_ta &sysrq_kill_op, /* i */ NULL, /* j */ &sysrq_SAK_op, /* k */ - NULL, /* l */ + &sysrq_showallregs_op, /* l */ &sysrq_showmem_op, /* m */ &sysrq_unrt_op, /* n */ /* o: This will often be registered as 'Off' at init time */ Index: linux/drivers/char/tty_io.c =================================================================== --- linux.orig/drivers/char/tty_io.c +++ linux/drivers/char/tty_io.c @@ -257,6 +257,7 @@ static int check_tty_count(struct tty_st printk(KERN_WARNING "Warning: dev (%s) tty->count(%d) " "!= #fd's(%d) in %s\n", tty->name, tty->count, count, routine); + dump_stack(); return count; } #endif @@ -3624,10 +3625,14 @@ void tty_flip_buffer_push(struct tty_str tty->buf.tail->commit = tty->buf.tail->used; spin_unlock_irqrestore(&tty->buf.lock, flags); +#ifndef CONFIG_PREEMPT_RT if (tty->low_latency) flush_to_ldisc(&tty->buf.work.work); else schedule_delayed_work(&tty->buf.work, 1); +#else + flush_to_ldisc(&tty->buf.work.work); +#endif } EXPORT_SYMBOL(tty_flip_buffer_push); Index: linux/drivers/clocksource/acpi_pm.c =================================================================== --- linux.orig/drivers/clocksource/acpi_pm.c +++ linux/drivers/clocksource/acpi_pm.c @@ -30,13 +30,13 @@ */ u32 pmtmr_ioport __read_mostly; -static inline u32 read_pmtmr(void) +static notrace inline u32 read_pmtmr(void) { /* mask the output to 24 bits */ return inl(pmtmr_ioport) & ACPI_PM_MASK; } -u32 acpi_pm_read_verified(void) +u32 notrace acpi_pm_read_verified(void) { u32 v1 = 0, v2 = 0, v3 = 0; @@ -56,12 +56,12 @@ u32 acpi_pm_read_verified(void) return v2; } -static cycle_t acpi_pm_read_slow(void) +static notrace cycle_t acpi_pm_read_slow(void) { return (cycle_t)acpi_pm_read_verified(); } -static cycle_t acpi_pm_read(void) +static notrace cycle_t acpi_pm_read(void) { return (cycle_t)read_pmtmr(); } Index: linux/drivers/cpuidle/Kconfig =================================================================== --- /dev/null +++ linux/drivers/cpuidle/Kconfig @@ -0,0 +1,39 @@ +menu "CPU idle PM support" + +config CPU_IDLE + bool "CPU idle PM support" + help + CPU idle is a generic framework for supporting software-controlled + idle processor power management. It includes modular cross-platform + governors that can be swapped during runtime. + + If you're using a mobile platform that supports CPU idle PM (e.g. + an ACPI-capable notebook), you should say Y here. + +if CPU_IDLE + +comment "Governors" + +config CPU_IDLE_GOV_LADDER + tristate "'ladder' governor" + depends on CPU_IDLE + default y + help + This cpuidle governor promotes and demotes through the supported idle + states using residency time and bus master activity as metrics. This + algorithm was originally introduced in the old ACPI processor driver. + +config CPU_IDLE_GOV_MENU + tristate "'menu' governor" + depends on CPU_IDLE && NO_HZ + default y + help + This cpuidle governor evaluates all available states and chooses the + deepest state that meets all of the following constraints: BM activity, + expected time until next timer interrupt, and last break event time + delta. It is designed to minimize power consumption. Currently + dynticks is required. + +endif # CPU_IDLE + +endmenu Index: linux/drivers/cpuidle/Makefile =================================================================== --- /dev/null +++ linux/drivers/cpuidle/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for cpuidle. +# + +obj-y += cpuidle.o driver.o governor.o sysfs.o governors/ Index: linux/drivers/cpuidle/cpuidle.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/cpuidle.c @@ -0,0 +1,306 @@ +/* + * cpuidle.c - core cpuidle infrastructure + * + * (C) 2006-2007 Venkatesh Pallipadi + * Shaohua Li + * Adam Belay + * + * This code is licenced under the GPL. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "cpuidle.h" + +DEFINE_PER_CPU(struct cpuidle_device *, cpuidle_devices); +EXPORT_PER_CPU_SYMBOL_GPL(cpuidle_devices); + +DEFINE_MUTEX(cpuidle_lock); +LIST_HEAD(cpuidle_detected_devices); +static void (*pm_idle_old)(void); + +/** + * cpuidle_idle_call - the main idle loop + * + * NOTE: no locks or semaphores should be used here + */ +static void cpuidle_idle_call(void) +{ + struct cpuidle_device *dev = __get_cpu_var(cpuidle_devices); + struct cpuidle_state *target_state; + int next_state; + + /* check if the device is ready */ + if (!dev || dev->status != CPUIDLE_STATUS_DOIDLE) { + if (pm_idle_old) + pm_idle_old(); + else + local_irq_enable(); + return; + } + + /* ask the governor for the next state */ + next_state = cpuidle_curr_governor->select(dev); + if (need_resched()) + return; + target_state = &dev->states[next_state]; + + /* enter the state and update stats */ + dev->last_residency = target_state->enter(dev, target_state); + dev->last_state = target_state; + target_state->time += dev->last_residency; + target_state->usage++; + + /* give the governor an opportunity to reflect on the outcome */ + if (cpuidle_curr_governor->reflect) + cpuidle_curr_governor->reflect(dev); +} + +/** + * cpuidle_install_idle_handler - installs the cpuidle idle loop handler + */ +void cpuidle_install_idle_handler(void) +{ + if (pm_idle != cpuidle_idle_call) { + /* Make sure all changes finished before we switch to new idle */ + smp_wmb(); + pm_idle = cpuidle_idle_call; + } +} + +/** + * cpuidle_uninstall_idle_handler - uninstalls the cpuidle idle loop handler + */ +void cpuidle_uninstall_idle_handler(void) +{ + if (pm_idle != pm_idle_old) { + pm_idle = pm_idle_old; + cpu_idle_wait(); + } +} + +/** + * cpuidle_rescan_device - prepares for a new state configuration + * @dev: the target device + * + * Must be called with cpuidle_lock aquired. + */ +void cpuidle_rescan_device(struct cpuidle_device *dev) +{ + int i; + + if (cpuidle_curr_governor->scan) + cpuidle_curr_governor->scan(dev); + + for (i = 0; i < dev->state_count; i++) { + dev->states[i].usage = 0; + dev->states[i].time = 0; + } +} + +/** + * cpuidle_add_device - attaches the driver to a CPU instance + * @sys_dev: the system device (driver model CPU representation) + */ +static int cpuidle_add_device(struct sys_device *sys_dev) +{ + int cpu = sys_dev->id; + struct cpuidle_device *dev; + + dev = per_cpu(cpuidle_devices, cpu); + + mutex_lock(&cpuidle_lock); + if (cpu_is_offline(cpu)) { + mutex_unlock(&cpuidle_lock); + return 0; + } + + if (!dev) { + dev = kzalloc(sizeof(struct cpuidle_device), GFP_KERNEL); + if (!dev) { + mutex_unlock(&cpuidle_lock); + return -ENOMEM; + } + init_completion(&dev->kobj_unregister); + per_cpu(cpuidle_devices, cpu) = dev; + } + dev->cpu = cpu; + + if (dev->status & CPUIDLE_STATUS_DETECTED) { + mutex_unlock(&cpuidle_lock); + return 0; + } + + cpuidle_add_sysfs(sys_dev); + + if (cpuidle_curr_driver) { + if (cpuidle_attach_driver(dev)) + goto err_ret; + } + + if (cpuidle_curr_governor) { + if (cpuidle_attach_governor(dev)) { + cpuidle_detach_driver(dev); + goto err_ret; + } + } + + if (cpuidle_device_can_idle(dev)) + cpuidle_install_idle_handler(); + + list_add(&dev->device_list, &cpuidle_detected_devices); + dev->status |= CPUIDLE_STATUS_DETECTED; + +err_ret: + mutex_unlock(&cpuidle_lock); + + return 0; +} + +/** + * __cpuidle_remove_device - detaches the driver from a CPU instance + * @sys_dev: the system device (driver model CPU representation) + * + * Must be called with cpuidle_lock aquired. + */ +static int __cpuidle_remove_device(struct sys_device *sys_dev) +{ + struct cpuidle_device *dev; + + dev = per_cpu(cpuidle_devices, sys_dev->id); + + if (!(dev->status & CPUIDLE_STATUS_DETECTED)) { + return 0; + } + dev->status &= ~CPUIDLE_STATUS_DETECTED; + /* NOTE: we don't wait because the cpu is already offline */ + if (cpuidle_curr_governor) + cpuidle_detach_governor(dev); + if (cpuidle_curr_driver) + cpuidle_detach_driver(dev); + cpuidle_remove_sysfs(sys_dev); + list_del(&dev->device_list); + wait_for_completion(&dev->kobj_unregister); + per_cpu(cpuidle_devices, sys_dev->id) = NULL; + kfree(dev); + + return 0; +} + +/** + * cpuidle_remove_device - detaches the driver from a CPU instance + * @sys_dev: the system device (driver model CPU representation) + */ +static int cpuidle_remove_device(struct sys_device *sys_dev) +{ + int ret; + mutex_lock(&cpuidle_lock); + ret = __cpuidle_remove_device(sys_dev); + mutex_unlock(&cpuidle_lock); + + return ret; +} + +static struct sysdev_driver cpuidle_sysdev_driver = { + .add = cpuidle_add_device, + .remove = cpuidle_remove_device, +}; + +static int cpuidle_cpu_callback(struct notifier_block *nfb, + unsigned long action, void *hcpu) +{ + struct sys_device *sys_dev; + + sys_dev = get_cpu_sysdev((unsigned long)hcpu); + + switch (action) { + case CPU_ONLINE: + cpuidle_add_device(sys_dev); + break; + case CPU_DOWN_PREPARE: + mutex_lock(&cpuidle_lock); + break; + case CPU_DEAD: + __cpuidle_remove_device(sys_dev); + mutex_unlock(&cpuidle_lock); + break; + case CPU_DOWN_FAILED: + mutex_unlock(&cpuidle_lock); + break; + } + + return NOTIFY_OK; +} + +static struct notifier_block __cpuinitdata cpuidle_cpu_notifier = +{ + .notifier_call = cpuidle_cpu_callback, +}; + +#ifdef CONFIG_SMP + +static void smp_callback(void *v) +{ + /* we already woke the CPU up, nothing more to do */ +} + +/* + * This function gets called when a part of the kernel has a new latency + * requirement. This means we need to get all processors out of their C-state, + * and then recalculate a new suitable C-state. Just do a cross-cpu IPI; that + * wakes them all right up. + */ +static int cpuidle_latency_notify(struct notifier_block *b, + unsigned long l, void *v) +{ + smp_call_function(smp_callback, NULL, 0, 1); + return NOTIFY_OK; +} + +static struct notifier_block cpuidle_latency_notifier = { + .notifier_call = cpuidle_latency_notify, +}; + +#define latency_notifier_init(x) do { register_latency_notifier(x); } while (0) + +#else /* CONFIG_SMP */ + +#define latency_notifier_init(x) do { } while (0) + +#endif /* CONFIG_SMP */ + +/** + * cpuidle_init - core initializer + */ +static int __init cpuidle_init(void) +{ + int ret; + + pm_idle_old = pm_idle; + + ret = cpuidle_add_class_sysfs(&cpu_sysdev_class); + if (ret) + return ret; + + register_hotcpu_notifier(&cpuidle_cpu_notifier); + + ret = sysdev_driver_register(&cpu_sysdev_class, &cpuidle_sysdev_driver); + + if (ret) { + cpuidle_remove_class_sysfs(&cpu_sysdev_class); + printk(KERN_ERR "cpuidle: failed to initialize\n"); + return ret; + } + + latency_notifier_init(&cpuidle_latency_notifier); + + return 0; +} + +core_initcall(cpuidle_init); Index: linux/drivers/cpuidle/cpuidle.h =================================================================== --- /dev/null +++ linux/drivers/cpuidle/cpuidle.h @@ -0,0 +1,50 @@ +/* + * cpuidle.h - The internal header file + */ + +#ifndef __DRIVER_CPUIDLE_H +#define __DRIVER_CPUIDLE_H + +#include + +/* For internal use only */ +extern struct cpuidle_governor *cpuidle_curr_governor; +extern struct cpuidle_driver *cpuidle_curr_driver; +extern struct list_head cpuidle_drivers; +extern struct list_head cpuidle_governors; +extern struct list_head cpuidle_detected_devices; +extern struct mutex cpuidle_lock; + +/* idle loop */ +extern void cpuidle_install_idle_handler(void); +extern void cpuidle_uninstall_idle_handler(void); +extern void cpuidle_rescan_device(struct cpuidle_device *dev); + +/* drivers */ +extern int cpuidle_attach_driver(struct cpuidle_device *dev); +extern void cpuidle_detach_driver(struct cpuidle_device *dev); +extern int cpuidle_switch_driver(struct cpuidle_driver *drv); + +/* governors */ +extern int cpuidle_attach_governor(struct cpuidle_device *dev); +extern void cpuidle_detach_governor(struct cpuidle_device *dev); +extern int cpuidle_switch_governor(struct cpuidle_governor *gov); + +/* sysfs */ +extern int cpuidle_add_class_sysfs(struct sysdev_class *cls); +extern void cpuidle_remove_class_sysfs(struct sysdev_class *cls); +extern int cpuidle_add_driver_sysfs(struct cpuidle_device *device); +extern void cpuidle_remove_driver_sysfs(struct cpuidle_device *device); +extern int cpuidle_add_sysfs(struct sys_device *sysdev); +extern void cpuidle_remove_sysfs(struct sys_device *sysdev); + +/** + * cpuidle_device_can_idle - determines if a CPU can utilize the idle loop + * @dev: the target CPU + */ +static inline int cpuidle_device_can_idle(struct cpuidle_device *dev) +{ + return (dev->status == CPUIDLE_STATUS_DOIDLE); +} + +#endif /* __DRIVER_CPUIDLE_H */ Index: linux/drivers/cpuidle/driver.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/driver.c @@ -0,0 +1,276 @@ +/* + * driver.c - driver support + * + * (C) 2006-2007 Venkatesh Pallipadi + * Shaohua Li + * Adam Belay + * + * This code is licenced under the GPL. + */ + +#include +#include +#include + +#include "cpuidle.h" + +LIST_HEAD(cpuidle_drivers); +struct cpuidle_driver *cpuidle_curr_driver; + + +/** + * cpuidle_attach_driver - attaches a driver to a CPU + * @dev: the target CPU + * + * Must be called with cpuidle_lock aquired. + */ +int cpuidle_attach_driver(struct cpuidle_device *dev) +{ + int ret; + + if (dev->status & CPUIDLE_STATUS_DRIVER_ATTACHED) + return -EIO; + + if (!try_module_get(cpuidle_curr_driver->owner)) + return -EINVAL; + + ret = cpuidle_curr_driver->init(dev); + if (ret) { + module_put(cpuidle_curr_driver->owner); + printk(KERN_INFO "cpuidle: driver %s failed to attach to " + "cpu %d\n", cpuidle_curr_driver->name, dev->cpu); + } else { + if (dev->status & CPUIDLE_STATUS_GOVERNOR_ATTACHED) + cpuidle_rescan_device(dev); + smp_wmb(); + dev->status |= CPUIDLE_STATUS_DRIVER_ATTACHED; + cpuidle_add_driver_sysfs(dev); + } + + return ret; +} + +/** + * cpuidle_detach_govenor - detaches a driver from a CPU + * @dev: the target CPU + * + * Must be called with cpuidle_lock aquired. + */ +void cpuidle_detach_driver(struct cpuidle_device *dev) +{ + if (dev->status & CPUIDLE_STATUS_DRIVER_ATTACHED) { + cpuidle_remove_driver_sysfs(dev); + dev->status &= ~CPUIDLE_STATUS_DRIVER_ATTACHED; + if (cpuidle_curr_driver->exit) + cpuidle_curr_driver->exit(dev); + module_put(cpuidle_curr_driver->owner); + } +} + +/** + * __cpuidle_find_driver - finds a driver of the specified name + * @str: the name + * + * Must be called with cpuidle_lock aquired. + */ +static struct cpuidle_driver * __cpuidle_find_driver(const char *str) +{ + struct cpuidle_driver *drv; + + list_for_each_entry(drv, &cpuidle_drivers, driver_list) + if (!strnicmp(str, drv->name, CPUIDLE_NAME_LEN)) + return drv; + + return NULL; +} + +/** + * cpuidle_switch_driver - changes the driver + * @drv: the new target driver + * + * NOTE: "drv" can be NULL to specify disabled + * Must be called with cpuidle_lock aquired. + */ +int cpuidle_switch_driver(struct cpuidle_driver *drv) +{ + struct cpuidle_device *dev; + + if (drv == cpuidle_curr_driver) + return -EINVAL; + + cpuidle_uninstall_idle_handler(); + + if (cpuidle_curr_driver) + list_for_each_entry(dev, &cpuidle_detected_devices, device_list) + cpuidle_detach_driver(dev); + + cpuidle_curr_driver = drv; + + if (drv) { + int ret = 1; + list_for_each_entry(dev, &cpuidle_detected_devices, device_list) + if (cpuidle_attach_driver(dev) == 0) + ret = 0; + + /* If attach on all devices fail, switch to NULL driver */ + if (ret) + cpuidle_curr_driver = NULL; + + if (cpuidle_curr_driver && cpuidle_curr_governor) { + printk(KERN_INFO "cpuidle: using driver %s\n", + drv->name); + cpuidle_install_idle_handler(); + } + } + + return 0; +} + +/** + * cpuidle_register_driver - registers a driver + * @drv: the driver + */ +int cpuidle_register_driver(struct cpuidle_driver *drv) +{ + int ret = -EEXIST; + + if (!drv || !drv->init) + return -EINVAL; + + mutex_lock(&cpuidle_lock); + if (__cpuidle_find_driver(drv->name) == NULL) { + ret = 0; + list_add_tail(&drv->driver_list, &cpuidle_drivers); + if (!cpuidle_curr_driver) + cpuidle_switch_driver(drv); + } + mutex_unlock(&cpuidle_lock); + + return ret; +} + +EXPORT_SYMBOL_GPL(cpuidle_register_driver); + +/** + * cpuidle_unregister_driver - unregisters a driver + * @drv: the driver + */ +void cpuidle_unregister_driver(struct cpuidle_driver *drv) +{ + if (!drv) + return; + + mutex_lock(&cpuidle_lock); + if (drv == cpuidle_curr_driver) + cpuidle_switch_driver(NULL); + list_del(&drv->driver_list); + mutex_unlock(&cpuidle_lock); +} + +EXPORT_SYMBOL_GPL(cpuidle_unregister_driver); + +static void __cpuidle_force_redetect(struct cpuidle_device *dev) +{ + cpuidle_remove_driver_sysfs(dev); + cpuidle_curr_driver->redetect(dev); + cpuidle_add_driver_sysfs(dev); +} + +/** + * cpuidle_force_redetect - redetects the idle states of a CPU + * + * @dev: the CPU to redetect + * @drv: the target driver + * + * Generally, the driver will call this when the supported states set has + * changed. (e.g. as the result of an ACPI transition to battery power) + */ +int cpuidle_force_redetect(struct cpuidle_device *dev, + struct cpuidle_driver *drv) +{ + int uninstalled = 0; + + mutex_lock(&cpuidle_lock); + + if (drv != cpuidle_curr_driver) { + mutex_unlock(&cpuidle_lock); + return 0; + } + + if (!(dev->status & CPUIDLE_STATUS_DRIVER_ATTACHED) || + !cpuidle_curr_driver->redetect) { + mutex_unlock(&cpuidle_lock); + return -EIO; + } + + if (cpuidle_device_can_idle(dev)) { + uninstalled = 1; + cpuidle_uninstall_idle_handler(); + } + + __cpuidle_force_redetect(dev); + + if (cpuidle_device_can_idle(dev)) { + cpuidle_rescan_device(dev); + cpuidle_install_idle_handler(); + } + + /* other devices are still ok */ + if (uninstalled) + cpuidle_install_idle_handler(); + + mutex_unlock(&cpuidle_lock); + + return 0; +} + +EXPORT_SYMBOL_GPL(cpuidle_force_redetect); + +/** + * cpuidle_force_redetect_devices - redetects the idle states of all CPUs + * + * @drv: the target driver + * + * Generally, the driver will call this when the supported states set has + * changed. (e.g. as the result of an ACPI transition to battery power) + */ +int cpuidle_force_redetect_devices(struct cpuidle_driver *drv) +{ + struct cpuidle_device *dev; + int ret = 0; + + mutex_lock(&cpuidle_lock); + + if (drv != cpuidle_curr_driver) + goto out; + + if (!cpuidle_curr_driver->redetect) { + ret = -EIO; + goto out; + } + + cpuidle_uninstall_idle_handler(); + + list_for_each_entry(dev, &cpuidle_detected_devices, device_list) + __cpuidle_force_redetect(dev); + + cpuidle_install_idle_handler(); +out: + mutex_unlock(&cpuidle_lock); + return ret; +} + +EXPORT_SYMBOL_GPL(cpuidle_force_redetect_devices); + +/** + * cpuidle_get_bm_activity - determines if BM activity has occured + */ +int cpuidle_get_bm_activity(void) +{ + if (cpuidle_curr_driver->bm_check) + return cpuidle_curr_driver->bm_check(); + else + return 0; +} +EXPORT_SYMBOL_GPL(cpuidle_get_bm_activity); + Index: linux/drivers/cpuidle/governor.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/governor.c @@ -0,0 +1,187 @@ +/* + * governor.c - governor support + * + * (C) 2006-2007 Venkatesh Pallipadi + * Shaohua Li + * Adam Belay + * + * This code is licenced under the GPL. + */ + +#include +#include +#include + +#include "cpuidle.h" + +LIST_HEAD(cpuidle_governors); +struct cpuidle_governor *cpuidle_curr_governor; + + +/** + * cpuidle_attach_governor - attaches a governor to a CPU + * @dev: the target CPU + * + * Must be called with cpuidle_lock aquired. + */ +int cpuidle_attach_governor(struct cpuidle_device *dev) +{ + int ret = 0; + + if(dev->status & CPUIDLE_STATUS_GOVERNOR_ATTACHED) + return -EIO; + + if (!try_module_get(cpuidle_curr_governor->owner)) + return -EINVAL; + + if (cpuidle_curr_governor->init) + ret = cpuidle_curr_governor->init(dev); + if (ret) { + module_put(cpuidle_curr_governor->owner); + printk(KERN_ERR "cpuidle: governor %s failed to attach to cpu %d\n", + cpuidle_curr_governor->name, dev->cpu); + } else { + if (dev->status & CPUIDLE_STATUS_DRIVER_ATTACHED) + cpuidle_rescan_device(dev); + smp_wmb(); + dev->status |= CPUIDLE_STATUS_GOVERNOR_ATTACHED; + } + + return ret; +} + +/** + * cpuidle_detach_govenor - detaches a governor from a CPU + * @dev: the target CPU + * + * Must be called with cpuidle_lock aquired. + */ +void cpuidle_detach_governor(struct cpuidle_device *dev) +{ + if (dev->status & CPUIDLE_STATUS_GOVERNOR_ATTACHED) { + dev->status &= ~CPUIDLE_STATUS_GOVERNOR_ATTACHED; + if (cpuidle_curr_governor->exit) + cpuidle_curr_governor->exit(dev); + module_put(cpuidle_curr_governor->owner); + } +} + +/** + * __cpuidle_find_governor - finds a governor of the specified name + * @str: the name + * + * Must be called with cpuidle_lock aquired. + */ +static struct cpuidle_governor * __cpuidle_find_governor(const char *str) +{ + struct cpuidle_governor *gov; + + list_for_each_entry(gov, &cpuidle_governors, governor_list) + if (!strnicmp(str, gov->name, CPUIDLE_NAME_LEN)) + return gov; + + return NULL; +} + +/** + * cpuidle_switch_governor - changes the governor + * @gov: the new target governor + * + * NOTE: "gov" can be NULL to specify disabled + * Must be called with cpuidle_lock aquired. + */ +int cpuidle_switch_governor(struct cpuidle_governor *gov) +{ + struct cpuidle_device *dev; + + if (gov == cpuidle_curr_governor) + return -EINVAL; + + cpuidle_uninstall_idle_handler(); + + if (cpuidle_curr_governor) + list_for_each_entry(dev, &cpuidle_detected_devices, device_list) + cpuidle_detach_governor(dev); + + cpuidle_curr_governor = gov; + + if (gov) { + list_for_each_entry(dev, &cpuidle_detected_devices, device_list) + cpuidle_attach_governor(dev); + if (cpuidle_curr_driver) + cpuidle_install_idle_handler(); + printk(KERN_INFO "cpuidle: using governor %s\n", gov->name); + } + + return 0; +} + +/** + * cpuidle_register_governor - registers a governor + * @gov: the governor + */ +int cpuidle_register_governor(struct cpuidle_governor *gov) +{ + int ret = -EEXIST; + + if (!gov || !gov->select) + return -EINVAL; + + mutex_lock(&cpuidle_lock); + if (__cpuidle_find_governor(gov->name) == NULL) { + ret = 0; + list_add_tail(&gov->governor_list, &cpuidle_governors); + if (!cpuidle_curr_governor || + cpuidle_curr_governor->rating < gov->rating) + cpuidle_switch_governor(gov); + } + mutex_unlock(&cpuidle_lock); + + return ret; +} + +EXPORT_SYMBOL_GPL(cpuidle_register_governor); + +/** + * cpuidle_replace_governor - find a replacement governor + * @exclude_rating: the rating that will be skipped while looking for + * new governor. + */ +struct cpuidle_governor *cpuidle_replace_governor(int exclude_rating) +{ + struct cpuidle_governor *gov; + struct cpuidle_governor *ret_gov = NULL; + unsigned int max_rating = 0; + + list_for_each_entry(gov, &cpuidle_governors, governor_list) { + if (gov->rating == exclude_rating) + continue; + if (gov->rating > max_rating) { + max_rating = gov->rating; + ret_gov = gov; + } + } + + return ret_gov; +} + +/** + * cpuidle_unregister_governor - unregisters a governor + * @gov: the governor + */ +void cpuidle_unregister_governor(struct cpuidle_governor *gov) +{ + if (!gov) + return; + + mutex_lock(&cpuidle_lock); + if (gov == cpuidle_curr_governor) { + struct cpuidle_governor *new_gov; + new_gov = cpuidle_replace_governor(gov->rating); + cpuidle_switch_governor(new_gov); + } + list_del(&gov->governor_list); + mutex_unlock(&cpuidle_lock); +} + +EXPORT_SYMBOL_GPL(cpuidle_unregister_governor); Index: linux/drivers/cpuidle/governors/Makefile =================================================================== --- /dev/null +++ linux/drivers/cpuidle/governors/Makefile @@ -0,0 +1,6 @@ +# +# Makefile for cpuidle governors. +# + +obj-$(CONFIG_CPU_IDLE_GOV_LADDER) += ladder.o +obj-$(CONFIG_CPU_IDLE_GOV_MENU) += menu.o Index: linux/drivers/cpuidle/governors/ladder.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/governors/ladder.c @@ -0,0 +1,228 @@ +/* + * ladder.c - the residency ladder algorithm + * + * Copyright (C) 2001, 2002 Andy Grover + * Copyright (C) 2001, 2002 Paul Diefenbaugh + * Copyright (C) 2004, 2005 Dominik Brodowski + * + * (C) 2006-2007 Venkatesh Pallipadi + * Shaohua Li + * Adam Belay + * + * This code is licenced under the GPL. + */ + +#include +#include +#include +#include +#include + +#include +#include + +#define PROMOTION_COUNT 4 +#define DEMOTION_COUNT 1 + +/* + * bm_history -- bit-mask with a bit per jiffy of bus-master activity + * 1000 HZ: 0xFFFFFFFF: 32 jiffies = 32ms + * 800 HZ: 0xFFFFFFFF: 32 jiffies = 40ms + * 100 HZ: 0x0000000F: 4 jiffies = 40ms + * reduce history for more aggressive entry into C3 + */ +static unsigned int bm_history __read_mostly = + (HZ >= 800 ? 0xFFFFFFFF : ((1U << (HZ / 25)) - 1)); +module_param(bm_history, uint, 0644); + +struct ladder_device_state { + struct { + u32 promotion_count; + u32 demotion_count; + u32 promotion_time; + u32 demotion_time; + u32 bm; + } threshold; + struct { + int promotion_count; + int demotion_count; + } stats; +}; + +struct ladder_device { + struct ladder_device_state states[CPUIDLE_STATE_MAX]; + unsigned int bm_check:1; + unsigned long bm_check_timestamp; + unsigned long bm_activity; /* FIXME: bm activity should be global */ + int last_state_idx; +}; + +/** + * ladder_do_selection - prepares private data for a state change + * @ldev: the ladder device + * @old_idx: the current state index + * @new_idx: the new target state index + */ +static inline void ladder_do_selection(struct ladder_device *ldev, + int old_idx, int new_idx) +{ + ldev->states[old_idx].stats.promotion_count = 0; + ldev->states[old_idx].stats.demotion_count = 0; + ldev->last_state_idx = new_idx; +} + +/** + * ladder_select_state - selects the next state to enter + * @dev: the CPU + */ +static int ladder_select_state(struct cpuidle_device *dev) +{ + struct ladder_device *ldev = dev->governor_data; + struct ladder_device_state *last_state; + int last_residency, last_idx = ldev->last_state_idx; + + if (unlikely(!ldev)) + return 0; + + last_state = &ldev->states[last_idx]; + + /* demote if within BM threshold */ + if (ldev->bm_check) { + unsigned long diff; + + diff = jiffies - ldev->bm_check_timestamp; + if (diff > 31) + diff = 31; + + ldev->bm_activity <<= diff; + if (cpuidle_get_bm_activity()) + ldev->bm_activity |= ((1 << diff) - 1); + + ldev->bm_check_timestamp = jiffies; + if ((last_idx > 0) && + (last_state->threshold.bm & ldev->bm_activity)) { + ladder_do_selection(ldev, last_idx, last_idx - 1); + return last_idx - 1; + } + } + + if (dev->states[last_idx].flags & CPUIDLE_FLAG_TIME_VALID) + last_residency = cpuidle_get_last_residency(dev) - dev->states[last_idx].exit_latency; + else + last_residency = last_state->threshold.promotion_time + 1; + + /* consider promotion */ + if (last_idx < dev->state_count - 1 && + last_residency > last_state->threshold.promotion_time && + dev->states[last_idx + 1].exit_latency <= system_latency_constraint()) { + last_state->stats.promotion_count++; + last_state->stats.demotion_count = 0; + if (last_state->stats.promotion_count >= last_state->threshold.promotion_count) { + ladder_do_selection(ldev, last_idx, last_idx + 1); + return last_idx + 1; + } + } + + /* consider demotion */ + if (last_idx > 0 && + last_residency < last_state->threshold.demotion_time) { + last_state->stats.demotion_count++; + last_state->stats.promotion_count = 0; + if (last_state->stats.demotion_count >= last_state->threshold.demotion_count) { + ladder_do_selection(ldev, last_idx, last_idx - 1); + return last_idx - 1; + } + } + + /* otherwise remain at the current state */ + return last_idx; +} + +/** + * ladder_scan_device - scans a CPU's states and does setup + * @dev: the CPU + */ +static void ladder_scan_device(struct cpuidle_device *dev) +{ + int i, bm_check = 0; + struct ladder_device *ldev = dev->governor_data; + struct ladder_device_state *lstate; + struct cpuidle_state *state; + + ldev->last_state_idx = 0; + ldev->bm_check_timestamp = 0; + ldev->bm_activity = 0; + + for (i = 0; i < dev->state_count; i++) { + state = &dev->states[i]; + lstate = &ldev->states[i]; + + lstate->stats.promotion_count = 0; + lstate->stats.demotion_count = 0; + + lstate->threshold.promotion_count = PROMOTION_COUNT; + lstate->threshold.demotion_count = DEMOTION_COUNT; + + if (i < dev->state_count - 1) + lstate->threshold.promotion_time = state->exit_latency; + if (i > 0) + lstate->threshold.demotion_time = state->exit_latency; + if (state->flags & CPUIDLE_FLAG_CHECK_BM) { + lstate->threshold.bm = bm_history; + bm_check = 1; + } else + lstate->threshold.bm = 0; + } + + ldev->bm_check = bm_check; +} + +/** + * ladder_init_device - initializes a CPU-instance + * @dev: the CPU + */ +static int ladder_init_device(struct cpuidle_device *dev) +{ + dev->governor_data = kmalloc(sizeof(struct ladder_device), GFP_KERNEL); + + return !dev->governor_data; +} + +/** + * ladder_exit_device - exits a CPU-instance + * @dev: the CPU + */ +static void ladder_exit_device(struct cpuidle_device *dev) +{ + kfree(dev->governor_data); +} + +static struct cpuidle_governor ladder_governor = { + .name = "ladder", + .rating = 10, + .init = ladder_init_device, + .exit = ladder_exit_device, + .scan = ladder_scan_device, + .select = ladder_select_state, + .owner = THIS_MODULE, +}; + +/** + * init_ladder - initializes the governor + */ +static int __init init_ladder(void) +{ + return cpuidle_register_governor(&ladder_governor); +} + +/** + * exit_ladder - exits the governor + */ +static void __exit exit_ladder(void) +{ + cpuidle_unregister_governor(&ladder_governor); +} + +MODULE_LICENSE("GPL"); +module_init(init_ladder); +module_exit(exit_ladder); Index: linux/drivers/cpuidle/governors/menu.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/governors/menu.c @@ -0,0 +1,181 @@ +/* + * menu.c - the menu idle governor + * + * Copyright (C) 2006-2007 Adam Belay + * + * This code is licenced under the GPL. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define BM_HOLDOFF 20000 /* 20 ms */ +#define DEMOTION_THRESHOLD 5 +#define DEMOTION_TIMEOUT_MULTIPLIER 1000 + +struct menu_device { + int last_state_idx; + + int deepest_break_state; + struct timespec break_expire_time_ts; + int break_last_cnt; + + int deepest_bm_state; + int bm_elapsed_us; + int bm_holdoff_us; +}; + +static DEFINE_PER_CPU(struct menu_device, menu_devices); + +/** + * menu_select - selects the next idle state to enter + * @dev: the CPU + */ +static int menu_select(struct cpuidle_device *dev) +{ + struct menu_device *data = &__get_cpu_var(menu_devices); + int i, expected_us, max_state = dev->state_count; + + /* discard BM history because it is sticky */ + cpuidle_get_bm_activity(); + + /* determine the expected residency time */ + expected_us = (s32) ktime_to_ns(tick_nohz_get_sleep_length()) / 1000; + + /* determine the maximum state compatible with current BM status */ + if (cpuidle_get_bm_activity()) + data->bm_elapsed_us = 0; + if (data->bm_elapsed_us <= data->bm_holdoff_us) + max_state = data->deepest_bm_state + 1; + + /* determine the maximum state compatible with recent idle breaks */ + if (data->deepest_break_state >= 0) { + struct timespec now; + ktime_get_ts(&now); + if (timespec_compare(&data->break_expire_time_ts, &now) > 0) { + max_state = min(max_state, + data->deepest_break_state + 1); + } else { + data->deepest_break_state = -1; + } + } + + /* find the deepest idle state that satisfies our constraints */ + for (i = 1; i < max_state; i++) { + struct cpuidle_state *s = &dev->states[i]; + + if (s->target_residency > expected_us) + break; + + if (s->exit_latency > system_latency_constraint()) + break; + } + + if (data->last_state_idx != i - 1) + data->break_last_cnt = 0; + + data->last_state_idx = i - 1; + return i - 1; +} + +/** + * menu_reflect - attempts to guess what happened after entry + * @dev: the CPU + * + * NOTE: it's important to be fast here because this operation will add to + * the overall exit latency. + */ +static void menu_reflect(struct cpuidle_device *dev) +{ + struct menu_device *data = &__get_cpu_var(menu_devices); + int last_idx = data->last_state_idx; + int measured_us = cpuidle_get_last_residency(dev); + struct cpuidle_state *target = &dev->states[last_idx]; + + /* + * Ugh, this idle state doesn't support residency measurements, so we + * are basically lost in the dark. As a compromise, assume we slept + * for one full standard timer tick. However, be aware that this + * could potentially result in a suboptimal state transition. + */ + if (!(target->flags & CPUIDLE_FLAG_TIME_VALID)) + measured_us = USEC_PER_SEC / HZ; + + data->bm_elapsed_us += measured_us; + + if (data->last_state_idx == 0) + return; + + /* + * Did something other than the timer interrupt + * cause an early break event? + */ + if (unlikely(measured_us < target->target_residency)) { + if (data->break_last_cnt > DEMOTION_THRESHOLD) { + data->deepest_break_state = data->last_state_idx - 1; + ktime_get_ts(&data->break_expire_time_ts); + timespec_add_ns(&data->break_expire_time_ts, + target->target_residency * + DEMOTION_TIMEOUT_MULTIPLIER); + } else { + data->break_last_cnt++; + } + } else { + if (data->break_last_cnt > 0) + data->break_last_cnt--; + } +} + +/** + * menu_scan_device - scans a CPU's states and does setup + * @dev: the CPU + */ +static void menu_scan_device(struct cpuidle_device *dev) +{ + struct menu_device *data = &per_cpu(menu_devices, dev->cpu); + int i; + + data->last_state_idx = 0; + data->bm_elapsed_us = 0; + data->bm_holdoff_us = BM_HOLDOFF; + data->deepest_break_state = -1; + + for (i = 1; i < dev->state_count; i++) + if (dev->states[i].flags & CPUIDLE_FLAG_CHECK_BM) + break; + data->deepest_bm_state = i - 1; +} + +struct cpuidle_governor menu_governor = { + .name = "menu", + .rating = 20, + .scan = menu_scan_device, + .select = menu_select, + .reflect = menu_reflect, + .owner = THIS_MODULE, +}; + +/** + * init_menu - initializes the governor + */ +static int __init init_menu(void) +{ + return cpuidle_register_governor(&menu_governor); +} + +/** + * exit_menu - exits the governor + */ +static void __exit exit_menu(void) +{ + cpuidle_unregister_governor(&menu_governor); +} + +MODULE_LICENSE("GPL"); +module_init(init_menu); +module_exit(exit_menu); Index: linux/drivers/cpuidle/sysfs.c =================================================================== --- /dev/null +++ linux/drivers/cpuidle/sysfs.c @@ -0,0 +1,393 @@ +/* + * sysfs.c - sysfs support + * + * (C) 2006-2007 Shaohua Li + * + * This code is licenced under the GPL. + */ + +#include +#include +#include +#include + +#include "cpuidle.h" + +static unsigned int sysfs_switch; +static int __init cpuidle_sysfs_setup(char *unused) +{ + sysfs_switch = 1; + return 1; +} +__setup("cpuidle_sysfs_switch", cpuidle_sysfs_setup); + +static ssize_t show_available_drivers(struct sys_device *dev, char *buf) +{ + ssize_t i = 0; + struct cpuidle_driver *tmp; + + mutex_lock(&cpuidle_lock); + list_for_each_entry(tmp, &cpuidle_drivers, driver_list) { + if (i >= (ssize_t)((PAGE_SIZE/sizeof(char)) - CPUIDLE_NAME_LEN - 2)) + goto out; + i += scnprintf(&buf[i], CPUIDLE_NAME_LEN, "%s ", tmp->name); + } +out: + i+= sprintf(&buf[i], "\n"); + mutex_unlock(&cpuidle_lock); + return i; +} + +static ssize_t show_available_governors(struct sys_device *dev, char *buf) +{ + ssize_t i = 0; + struct cpuidle_governor *tmp; + + mutex_lock(&cpuidle_lock); + list_for_each_entry(tmp, &cpuidle_governors, governor_list) { + if (i >= (ssize_t)((PAGE_SIZE/sizeof(char)) - CPUIDLE_NAME_LEN - 2)) + goto out; + i += scnprintf(&buf[i], CPUIDLE_NAME_LEN, "%s ", tmp->name); + } + if (list_empty(&cpuidle_governors)) + i+= sprintf(&buf[i], "no governors"); +out: + i+= sprintf(&buf[i], "\n"); + mutex_unlock(&cpuidle_lock); + return i; +} + +static ssize_t show_current_driver(struct sys_device *dev, char *buf) +{ + ssize_t ret; + + mutex_lock(&cpuidle_lock); + ret = sprintf(buf, "%s\n", cpuidle_curr_driver->name); + mutex_unlock(&cpuidle_lock); + return ret; +} + +static ssize_t store_current_driver(struct sys_device *dev, + const char *buf, size_t count) +{ + char str[CPUIDLE_NAME_LEN]; + int len = count; + struct cpuidle_driver *tmp, *found = NULL; + + if (len > CPUIDLE_NAME_LEN) + len = CPUIDLE_NAME_LEN; + + if (sscanf(buf, "%s", str) != 1) + return -EINVAL; + + mutex_lock(&cpuidle_lock); + list_for_each_entry(tmp, &cpuidle_drivers, driver_list) { + if (strncmp(tmp->name, str, CPUIDLE_NAME_LEN) == 0) { + found = tmp; + break; + } + } + if (found) + cpuidle_switch_driver(found); + mutex_unlock(&cpuidle_lock); + + return count; +} + +static ssize_t show_current_governor(struct sys_device *dev, char *buf) +{ + ssize_t i; + + mutex_lock(&cpuidle_lock); + if (cpuidle_curr_governor) + i = sprintf(buf, "%s\n", cpuidle_curr_governor->name); + else + i = sprintf(buf, "no governor\n"); + mutex_unlock(&cpuidle_lock); + + return i; +} + +static ssize_t store_current_governor(struct sys_device *dev, + const char *buf, size_t count) +{ + char str[CPUIDLE_NAME_LEN]; + int len = count; + struct cpuidle_governor *tmp, *found = NULL; + + if (len > CPUIDLE_NAME_LEN) + len = CPUIDLE_NAME_LEN; + + if (sscanf(buf, "%s", str) != 1) + return -EINVAL; + + mutex_lock(&cpuidle_lock); + list_for_each_entry(tmp, &cpuidle_governors, governor_list) { + if (strncmp(tmp->name, str, CPUIDLE_NAME_LEN) == 0) { + found = tmp; + break; + } + } + if (found) + cpuidle_switch_governor(found); + mutex_unlock(&cpuidle_lock); + + return count; +} + +static SYSDEV_ATTR(current_driver_ro, 0444, show_current_driver, NULL); +static SYSDEV_ATTR(current_governor_ro, 0444, show_current_governor, NULL); + +static struct attribute *cpuclass_default_attrs[] = { + &attr_current_driver_ro.attr, + &attr_current_governor_ro.attr, + NULL +}; + +static SYSDEV_ATTR(available_drivers, 0444, show_available_drivers, NULL); +static SYSDEV_ATTR(available_governors, 0444, show_available_governors, NULL); +static SYSDEV_ATTR(current_driver, 0644, show_current_driver, + store_current_driver); +static SYSDEV_ATTR(current_governor, 0644, show_current_governor, + store_current_governor); + +static struct attribute *cpuclass_switch_attrs[] = { + &attr_available_drivers.attr, + &attr_available_governors.attr, + &attr_current_driver.attr, + &attr_current_governor.attr, + NULL +}; + +static struct attribute_group cpuclass_attr_group = { + .attrs = cpuclass_default_attrs, + .name = "cpuidle", +}; + +/** + * cpuidle_add_class_sysfs - add CPU global sysfs attributes + */ +int cpuidle_add_class_sysfs(struct sysdev_class *cls) +{ + if (sysfs_switch) + cpuclass_attr_group.attrs = cpuclass_switch_attrs; + + return sysfs_create_group(&cls->kset.kobj, &cpuclass_attr_group); +} + +/** + * cpuidle_remove_class_sysfs - remove CPU global sysfs attributes + */ +void cpuidle_remove_class_sysfs(struct sysdev_class *cls) +{ + sysfs_remove_group(&cls->kset.kobj, &cpuclass_attr_group); +} + +struct cpuidle_attr { + struct attribute attr; + ssize_t (*show)(struct cpuidle_device *, char *); + ssize_t (*store)(struct cpuidle_device *, const char *, size_t count); +}; + +#define define_one_ro(_name, show) \ + static struct cpuidle_attr attr_##_name = __ATTR(_name, 0444, show, NULL) +#define define_one_rw(_name, show, store) \ + static struct cpuidle_attr attr_##_name = __ATTR(_name, 0644, show, store) + +#define kobj_to_cpuidledev(k) container_of(k, struct cpuidle_device, kobj) +#define attr_to_cpuidleattr(a) container_of(a, struct cpuidle_attr, attr) +static ssize_t cpuidle_show(struct kobject * kobj, struct attribute * attr ,char * buf) +{ + int ret = -EIO; + struct cpuidle_device *dev = kobj_to_cpuidledev(kobj); + struct cpuidle_attr * cattr = attr_to_cpuidleattr(attr); + + if (cattr->show) { + mutex_lock(&cpuidle_lock); + ret = cattr->show(dev, buf); + mutex_unlock(&cpuidle_lock); + } + return ret; +} + +static ssize_t cpuidle_store(struct kobject * kobj, struct attribute * attr, + const char * buf, size_t count) +{ + int ret = -EIO; + struct cpuidle_device *dev = kobj_to_cpuidledev(kobj); + struct cpuidle_attr * cattr = attr_to_cpuidleattr(attr); + + if (cattr->store) { + mutex_lock(&cpuidle_lock); + ret = cattr->store(dev, buf, count); + mutex_unlock(&cpuidle_lock); + } + return ret; +} + +static struct sysfs_ops cpuidle_sysfs_ops = { + .show = cpuidle_show, + .store = cpuidle_store, +}; + +static void cpuidle_sysfs_release(struct kobject *kobj) +{ + struct cpuidle_device *dev = kobj_to_cpuidledev(kobj); + + complete(&dev->kobj_unregister); +} + +static struct kobj_type ktype_cpuidle = { + .sysfs_ops = &cpuidle_sysfs_ops, + .release = cpuidle_sysfs_release, +}; + +struct cpuidle_state_attr { + struct attribute attr; + ssize_t (*show)(struct cpuidle_state *, char *); + ssize_t (*store)(struct cpuidle_state *, const char *, size_t); +}; + +#define define_one_state_ro(_name, show) \ +static struct cpuidle_state_attr attr_##_name = __ATTR(_name, 0444, show, NULL) + +#define define_show_state_function(_name) \ +static ssize_t show_state_##_name(struct cpuidle_state *state, char *buf) \ +{ \ + return sprintf(buf, "%d\n", state->_name);\ +} + +define_show_state_function(exit_latency) +define_show_state_function(power_usage) +define_show_state_function(usage) +define_show_state_function(time) +define_one_state_ro(latency, show_state_exit_latency); +define_one_state_ro(power, show_state_power_usage); +define_one_state_ro(usage, show_state_usage); +define_one_state_ro(time, show_state_time); + +static struct attribute *cpuidle_state_default_attrs[] = { + &attr_latency.attr, + &attr_power.attr, + &attr_usage.attr, + &attr_time.attr, + NULL +}; + +#define kobj_to_state_obj(k) container_of(k, struct cpuidle_state_kobj, kobj) +#define kobj_to_state(k) (kobj_to_state_obj(k)->state) +#define attr_to_stateattr(a) container_of(a, struct cpuidle_state_attr, attr) +static ssize_t cpuidle_state_show(struct kobject * kobj, + struct attribute * attr ,char * buf) +{ + int ret = -EIO; + struct cpuidle_state *state = kobj_to_state(kobj); + struct cpuidle_state_attr * cattr = attr_to_stateattr(attr); + + if (cattr->show) + ret = cattr->show(state, buf); + + return ret; +} + +static struct sysfs_ops cpuidle_state_sysfs_ops = { + .show = cpuidle_state_show, +}; + +static void cpuidle_state_sysfs_release(struct kobject *kobj) +{ + struct cpuidle_state_kobj *state_obj = kobj_to_state_obj(kobj); + + complete(&state_obj->kobj_unregister); +} + +static struct kobj_type ktype_state_cpuidle = { + .sysfs_ops = &cpuidle_state_sysfs_ops, + .default_attrs = cpuidle_state_default_attrs, + .release = cpuidle_state_sysfs_release, +}; + +static void inline cpuidle_free_state_kobj(struct cpuidle_device *device, int i) +{ + kobject_unregister(&device->kobjs[i]->kobj); + wait_for_completion(&device->kobjs[i]->kobj_unregister); + kfree(device->kobjs[i]); + device->kobjs[i] = NULL; +} + +/** + * cpuidle_add_driver_sysfs - adds driver-specific sysfs attributes + * @device: the target device + */ +int cpuidle_add_driver_sysfs(struct cpuidle_device *device) +{ + int i, ret = -ENOMEM; + struct cpuidle_state_kobj *kobj; + + /* state statistics */ + for (i = 0; i < device->state_count; i++) { + kobj = kzalloc(sizeof(struct cpuidle_state_kobj), GFP_KERNEL); + if (!kobj) + goto error_state; + kobj->state = &device->states[i]; + init_completion(&kobj->kobj_unregister); + + kobj->kobj.parent = &device->kobj; + kobj->kobj.ktype = &ktype_state_cpuidle; + kobject_set_name(&kobj->kobj, "state%d", i); + ret = kobject_register(&kobj->kobj); + if (ret) { + kfree(kobj); + goto error_state; + } + device->kobjs[i] = kobj; + } + + return 0; + +error_state: + for (i = i - 1; i >= 0; i--) + cpuidle_free_state_kobj(device, i); + return ret; +} + +/** + * cpuidle_remove_driver_sysfs - removes driver-specific sysfs attributes + * @device: the target device + */ +void cpuidle_remove_driver_sysfs(struct cpuidle_device *device) +{ + int i; + + for (i = 0; i < device->state_count; i++) + cpuidle_free_state_kobj(device, i); +} + +/** + * cpuidle_add_sysfs - creates a sysfs instance for the target device + * @sysdev: the target device + */ +int cpuidle_add_sysfs(struct sys_device *sysdev) +{ + int cpu = sysdev->id; + struct cpuidle_device *dev; + + dev = per_cpu(cpuidle_devices, cpu); + dev->kobj.parent = &sysdev->kobj; + dev->kobj.ktype = &ktype_cpuidle; + kobject_set_name(&dev->kobj, "%s", "cpuidle"); + return kobject_register(&dev->kobj); +} + +/** + * cpuidle_remove_sysfs - deletes a sysfs instance on the target device + * @sysdev: the target device + */ +void cpuidle_remove_sysfs(struct sys_device *sysdev) +{ + int cpu = sysdev->id; + struct cpuidle_device *dev; + + dev = per_cpu(cpuidle_devices, cpu); + kobject_unregister(&dev->kobj); +} Index: linux/drivers/ide/ide-floppy.c =================================================================== --- linux.orig/drivers/ide/ide-floppy.c +++ linux/drivers/ide/ide-floppy.c @@ -1667,9 +1667,9 @@ static int idefloppy_get_format_progress atapi_status_t status; unsigned long flags; - local_irq_save(flags); + local_irq_save_nort(flags); status.all = HWIF(drive)->INB(IDE_STATUS_REG); - local_irq_restore(flags); + local_irq_restore_nort(flags); progress_indication = !status.b.dsc ? 0 : 0x10000; } Index: linux/drivers/ide/ide-io.c =================================================================== --- linux.orig/drivers/ide/ide-io.c +++ linux/drivers/ide/ide-io.c @@ -1193,7 +1193,7 @@ static void ide_do_request (ide_hwgroup_ ide_get_lock(ide_intr, hwgroup); /* caller must own ide_lock */ - BUG_ON(!irqs_disabled()); + BUG_ON_NONRT(!irqs_disabled()); while (!hwgroup->busy) { hwgroup->busy = 1; @@ -1461,7 +1461,7 @@ void ide_timer_expiry (unsigned long dat #endif /* DISABLE_IRQ_NOSYNC */ /* local CPU only, * as if we were handling an interrupt */ - local_irq_disable(); + local_irq_disable_nort(); if (hwgroup->polling) { startstop = handler(drive); } else if (drive_is_ready(drive)) { Index: linux/drivers/ide/ide-iops.c =================================================================== --- linux.orig/drivers/ide/ide-iops.c +++ linux/drivers/ide/ide-iops.c @@ -220,10 +220,10 @@ static void ata_input_data(ide_drive_t * if (io_32bit) { if (io_32bit & 2) { unsigned long flags; - local_irq_save(flags); + local_irq_save_nort(flags); ata_vlb_sync(drive, IDE_NSECTOR_REG); hwif->INSL(IDE_DATA_REG, buffer, wcount); - local_irq_restore(flags); + local_irq_restore_nort(flags); } else hwif->INSL(IDE_DATA_REG, buffer, wcount); } else { @@ -242,10 +242,10 @@ static void ata_output_data(ide_drive_t if (io_32bit) { if (io_32bit & 2) { unsigned long flags; - local_irq_save(flags); + local_irq_save_nort(flags); ata_vlb_sync(drive, IDE_NSECTOR_REG); hwif->OUTSL(IDE_DATA_REG, buffer, wcount); - local_irq_restore(flags); + local_irq_restore_nort(flags); } else hwif->OUTSL(IDE_DATA_REG, buffer, wcount); } else { @@ -540,12 +540,12 @@ int ide_wait_stat (ide_startstop_t *star if (!(stat & BUSY_STAT)) break; - local_irq_restore(flags); + local_irq_restore_nort(flags); *startstop = ide_error(drive, "status timeout", stat); return 1; } } - local_irq_restore(flags); + local_irq_restore_nort(flags); } /* * Allow status to settle, then read it again. @@ -716,17 +716,15 @@ int ide_driveid_update (ide_drive_t *dri printk("%s: CHECK for good STATUS\n", drive->name); return 0; } - local_irq_save(flags); - SELECT_MASK(drive, 0); id = kmalloc(SECTOR_WORDS*4, GFP_ATOMIC); - if (!id) { - local_irq_restore(flags); + if (!id) return 0; - } + local_irq_save_nort(flags); + SELECT_MASK(drive, 0); ata_input_data(drive, id, SECTOR_WORDS); (void) hwif->INB(IDE_STATUS_REG); /* clear drive IRQ */ - local_irq_enable(); - local_irq_restore(flags); + local_irq_enable_nort(); + local_irq_restore_nort(flags); ide_fix_driveid(id); if (id) { drive->id->dma_ultra = id->dma_ultra; @@ -806,7 +804,7 @@ int ide_config_drive_speed (ide_drive_t if (time_after(jiffies, timeout)) break; } - local_irq_restore(flags); + local_irq_restore_nort(flags); } /* Index: linux/drivers/ide/ide-lib.c =================================================================== --- linux.orig/drivers/ide/ide-lib.c +++ linux/drivers/ide/ide-lib.c @@ -376,15 +376,16 @@ int ide_set_xfer_rate(ide_drive_t *drive static void ide_dump_opcode(ide_drive_t *drive) { + unsigned long flags; struct request *rq; u8 opcode = 0; int found = 0; - spin_lock(&ide_lock); + spin_lock_irqsave(&ide_lock, flags); rq = NULL; if (HWGROUP(drive)) rq = HWGROUP(drive)->rq; - spin_unlock(&ide_lock); + spin_unlock_irqrestore(&ide_lock, flags); if (!rq) return; if (rq->cmd_type == REQ_TYPE_ATA_CMD || @@ -413,10 +414,8 @@ static void ide_dump_opcode(ide_drive_t static u8 ide_dump_ata_status(ide_drive_t *drive, const char *msg, u8 stat) { ide_hwif_t *hwif = HWIF(drive); - unsigned long flags; u8 err = 0; - local_irq_save(flags); printk("%s: %s: status=0x%02x { ", drive->name, msg, stat); if (stat & BUSY_STAT) printk("Busy "); @@ -476,7 +475,7 @@ static u8 ide_dump_ata_status(ide_drive_ printk("\n"); } ide_dump_opcode(drive); - local_irq_restore(flags); + return err; } @@ -491,14 +490,11 @@ static u8 ide_dump_ata_status(ide_drive_ static u8 ide_dump_atapi_status(ide_drive_t *drive, const char *msg, u8 stat) { - unsigned long flags; - atapi_status_t status; atapi_error_t error; status.all = stat; error.all = 0; - local_irq_save(flags); printk("%s: %s: status=0x%02x { ", drive->name, msg, stat); if (status.b.bsy) printk("Busy "); @@ -524,7 +520,7 @@ static u8 ide_dump_atapi_status(ide_driv printk("}\n"); } ide_dump_opcode(drive); - local_irq_restore(flags); + return error.all; } Index: linux/drivers/ide/ide-probe.c =================================================================== --- linux.orig/drivers/ide/ide-probe.c +++ linux/drivers/ide/ide-probe.c @@ -141,7 +141,7 @@ static inline void do_identify (ide_driv hwif->ata_input_data(drive, id, SECTOR_WORDS); drive->id_read = 1; - local_irq_enable(); + local_irq_enable_nort(); ide_fix_driveid(id); #if defined (CONFIG_SCSI_EATA_DMA) || defined (CONFIG_SCSI_EATA_PIO) || defined (CONFIG_SCSI_EATA) @@ -323,14 +323,14 @@ static int actual_try_to_identify (ide_d unsigned long flags; /* local CPU only; some systems need this */ - local_irq_save(flags); + local_irq_save_nort(flags); /* drive returned ID */ do_identify(drive, cmd); /* drive responded with ID */ rc = 0; /* clear drive IRQ */ (void) hwif->INB(IDE_STATUS_REG); - local_irq_restore(flags); + local_irq_restore_nort(flags); } else { /* drive refused ID */ rc = 2; @@ -807,7 +807,7 @@ static void probe_hwif(ide_hwif_t *hwif, } while ((stat & BUSY_STAT) && time_after(timeout, jiffies)); } - local_irq_restore(flags); + local_irq_restore_nort(flags); /* * Use cached IRQ number. It might be (and is...) changed by probe * code above Index: linux/drivers/ide/ide-taskfile.c =================================================================== --- linux.orig/drivers/ide/ide-taskfile.c +++ linux/drivers/ide/ide-taskfile.c @@ -278,7 +278,7 @@ static void ide_pio_sector(ide_drive_t * offset %= PAGE_SIZE; #ifdef CONFIG_HIGHMEM - local_irq_save(flags); + local_irq_save_nort(flags); #endif buf = kmap_atomic(page, KM_BIO_SRC_IRQ) + offset; @@ -298,7 +298,7 @@ static void ide_pio_sector(ide_drive_t * kunmap_atomic(buf, KM_BIO_SRC_IRQ); #ifdef CONFIG_HIGHMEM - local_irq_restore(flags); + local_irq_restore_nort(flags); #endif } @@ -464,7 +464,7 @@ ide_startstop_t pre_task_out_intr (ide_d } if (!drive->unmask) - local_irq_disable(); + local_irq_disable_nort(); ide_set_handler(drive, &task_out_intr, WAIT_WORSTCASE, NULL); ide_pio_datablock(drive, rq, 1); Index: linux/drivers/ide/pci/alim15x3.c =================================================================== --- linux.orig/drivers/ide/pci/alim15x3.c +++ linux/drivers/ide/pci/alim15x3.c @@ -325,7 +325,7 @@ static u8 ali15x3_tune_pio (ide_drive_t if (r_clc >= 16) r_clc = 0; } - local_irq_save(flags); + local_irq_save_nort(flags); /* * PIO mode => ATA FIFO on, ATAPI FIFO off @@ -347,7 +347,7 @@ static u8 ali15x3_tune_pio (ide_drive_t pci_write_config_byte(dev, port, s_clc); pci_write_config_byte(dev, port+drive->select.b.unit+2, (a_clc << 4) | r_clc); - local_irq_restore(flags); + local_irq_restore_nort(flags); /* * setup active rec @@ -518,7 +518,7 @@ static unsigned int __devinit init_chips } #endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */ - local_irq_save(flags); + local_irq_save_nort(flags); if (m5229_revision < 0xC2) { /* @@ -579,7 +579,7 @@ static unsigned int __devinit init_chips out: pci_dev_put(north); pci_dev_put(isa_dev); - local_irq_restore(flags); + local_irq_restore_nort(flags); return 0; } @@ -603,7 +603,7 @@ static unsigned int __devinit ata66_ali1 unsigned long flags; u8 tmpbyte; - local_irq_save(flags); + local_irq_save_nort(flags); if (m5229_revision >= 0xC2) { /* @@ -655,7 +655,7 @@ static unsigned int __devinit ata66_ali1 pci_write_config_byte(dev, 0x53, tmpbyte); - local_irq_restore(flags); + local_irq_restore_nort(flags); return(ata66); } Index: linux/drivers/ide/pci/cs5530.c =================================================================== --- linux.orig/drivers/ide/pci/cs5530.c +++ linux/drivers/ide/pci/cs5530.c @@ -227,8 +227,8 @@ static unsigned int __devinit init_chips goto out; } - spin_lock_irqsave(&ide_lock, flags); - /* all CPUs (there should only be one CPU with this chipset) */ + /* Local CPU. ide_lock is acquired in do_ide_setup_pci_device. */ + local_irq_save(flags); /* * Enable BusMaster and MemoryWriteAndInvalidate for the cs5530: @@ -280,7 +280,7 @@ static unsigned int __devinit init_chips pci_write_config_byte(master_0, 0x42, 0x00); pci_write_config_byte(master_0, 0x43, 0xc1); - spin_unlock_irqrestore(&ide_lock, flags); + local_irq_restore(flags); out: pci_dev_put(master_0); Index: linux/drivers/ide/pci/hpt366.c =================================================================== --- linux.orig/drivers/ide/pci/hpt366.c +++ linux/drivers/ide/pci/hpt366.c @@ -1371,7 +1371,7 @@ static void __devinit init_dma_hpt366(id dma_old = hwif->INB(dmabase + 2); - local_irq_save(flags); + local_irq_save_nort(flags); dma_new = dma_old; pci_read_config_byte(dev, hwif->channel ? 0x4b : 0x43, &masterdma); @@ -1382,7 +1382,7 @@ static void __devinit init_dma_hpt366(id if (dma_new != dma_old) hwif->OUTB(dma_new, dmabase + 2); - local_irq_restore(flags); + local_irq_restore_nort(flags); ide_setup_dma(hwif, dmabase, 8); } Index: linux/drivers/input/ff-memless.c =================================================================== --- linux.orig/drivers/input/ff-memless.c +++ linux/drivers/input/ff-memless.c @@ -28,6 +28,7 @@ #include #include #include +#include #include #include Index: linux/drivers/input/gameport/gameport.c =================================================================== --- linux.orig/drivers/input/gameport/gameport.c +++ linux/drivers/input/gameport/gameport.c @@ -21,6 +21,7 @@ #include #include #include +#include #include /* HZ */ #include #include @@ -102,12 +103,12 @@ static int gameport_measure_speed(struct tx = 1 << 30; for(i = 0; i < 50; i++) { - local_irq_save(flags); + local_irq_save_nort(flags); GET_TIME(t1); for (t = 0; t < 50; t++) gameport_read(gameport); GET_TIME(t2); GET_TIME(t3); - local_irq_restore(flags); + local_irq_restore_nort(flags); udelay(i * 10); if ((t = DELTA(t2,t1) - DELTA(t3,t2)) < tx) tx = t; } @@ -126,11 +127,11 @@ static int gameport_measure_speed(struct tx = 1 << 30; for(i = 0; i < 50; i++) { - local_irq_save(flags); + local_irq_save_nort(flags); rdtscl(t1); for (t = 0; t < 50; t++) gameport_read(gameport); rdtscl(t2); - local_irq_restore(flags); + local_irq_restore_nort(flags); udelay(i * 10); if (t2 - t1 < tx) tx = t2 - t1; } Index: linux/drivers/input/keyboard/atkbd.c =================================================================== --- linux.orig/drivers/input/keyboard/atkbd.c +++ linux/drivers/input/keyboard/atkbd.c @@ -1396,9 +1396,23 @@ static ssize_t atkbd_show_err_count(stru return sprintf(buf, "%lu\n", atkbd->err_count); } +static int __read_mostly noatkbd; + +static int __init noatkbd_setup(char *str) +{ + noatkbd = 1; + printk(KERN_INFO "debug: not setting up AT keyboard.\n"); + + return 1; +} + +__setup("noatkbd", noatkbd_setup); static int __init atkbd_init(void) { + if (noatkbd) + return 0; + return serio_register_driver(&atkbd_drv); } Index: linux/drivers/input/misc/pcspkr.c =================================================================== --- linux.orig/drivers/input/misc/pcspkr.c +++ linux/drivers/input/misc/pcspkr.c @@ -24,7 +24,12 @@ MODULE_AUTHOR("Vojtech Pavlik +#else +static DEFINE_SPINLOCK(i8253_lock); +#endif static int pcspkr_event(struct input_dev *dev, unsigned int type, unsigned int code, int value) { @@ -43,7 +48,7 @@ static int pcspkr_event(struct input_dev if (value > 20 && value < 32767) count = PIT_TICK_RATE / value; - spin_lock_irqsave(&i8253_beep_lock, flags); + spin_lock_irqsave(&i8253_lock, flags); if (count) { /* enable counter 2 */ @@ -58,7 +63,7 @@ static int pcspkr_event(struct input_dev outb(inb_p(0x61) & 0xFC, 0x61); } - spin_unlock_irqrestore(&i8253_beep_lock, flags); + spin_unlock_irqrestore(&i8253_lock, flags); return 0; } Index: linux/drivers/input/mouse/psmouse-base.c =================================================================== --- linux.orig/drivers/input/mouse/psmouse-base.c +++ linux/drivers/input/mouse/psmouse-base.c @@ -1565,10 +1565,25 @@ static int psmouse_get_maxproto(char *bu return sprintf(buffer, "%s\n", psmouse_protocol_by_type(type)->name); } +static int __read_mostly nopsmouse; + +static int __init nopsmouse_setup(char *str) +{ + nopsmouse = 1; + printk(KERN_INFO "debug: not setting up psmouse.\n"); + + return 1; +} + +__setup("nopsmouse", nopsmouse_setup); + static int __init psmouse_init(void) { int err; + if (nopsmouse) + return 0; + kpsmoused_wq = create_singlethread_workqueue("kpsmoused"); if (!kpsmoused_wq) { printk(KERN_ERR "psmouse: failed to create kpsmoused workqueue\n"); Index: linux/drivers/kvm/svm.c =================================================================== --- linux.orig/drivers/kvm/svm.c +++ linux/drivers/kvm/svm.c @@ -610,9 +610,17 @@ static void svm_free_vcpu(struct kvm_vcp static void svm_vcpu_load(struct kvm_vcpu *vcpu) { - int cpu, i; + int cpu = raw_smp_processor_id(), i; + cpumask_t this_mask = cpumask_of_cpu(cpu); + + /* + * Keep the context preemptible, but do not migrate + * away to another CPU. TODO: make sure this persists. + * Save/restore original mask. + */ + if (unlikely(!cpus_equal(current->cpus_allowed, this_mask))) + set_cpus_allowed(current, cpumask_of_cpu(cpu)); - cpu = get_cpu(); if (unlikely(cpu != vcpu->cpu)) { u64 tsc_this, delta; @@ -638,7 +646,6 @@ static void svm_vcpu_put(struct kvm_vcpu wrmsrl(host_save_user_msrs[i], vcpu->svm->host_user_msrs[i]); rdtscll(vcpu->host_tsc); - put_cpu(); } static void svm_vcpu_decache(struct kvm_vcpu *vcpu) Index: linux/drivers/kvm/vmx.c =================================================================== --- linux.orig/drivers/kvm/vmx.c +++ linux/drivers/kvm/vmx.c @@ -241,9 +241,16 @@ static void vmcs_set_bits(unsigned long static void vmx_vcpu_load(struct kvm_vcpu *vcpu) { u64 phys_addr = __pa(vcpu->vmcs); - int cpu; + int cpu = raw_smp_processor_id(); + cpumask_t this_mask = cpumask_of_cpu(cpu); - cpu = get_cpu(); + /* + * Keep the context preemptible, but do not migrate + * away to another CPU. TODO: make sure this persists. + * Save/restore original mask. + */ + if (unlikely(!cpus_equal(current->cpus_allowed, this_mask))) + set_cpus_allowed(current, cpumask_of_cpu(cpu)); if (vcpu->cpu != cpu) vcpu_clear(vcpu); @@ -281,7 +288,6 @@ static void vmx_vcpu_load(struct kvm_vcp static void vmx_vcpu_put(struct kvm_vcpu *vcpu) { kvm_put_guest_fpu(vcpu); - put_cpu(); } static void vmx_vcpu_decache(struct kvm_vcpu *vcpu) @@ -1862,6 +1868,7 @@ again: } #endif + preempt_disable(); asm ( /* Store host registers */ "pushf \n\t" @@ -2002,6 +2009,8 @@ again: reload_tss(); } + preempt_enable(); + ++vcpu->stat.exits; #ifdef CONFIG_X86_64 Index: linux/drivers/macintosh/adb.c =================================================================== --- linux.orig/drivers/macintosh/adb.c +++ linux/drivers/macintosh/adb.c @@ -256,6 +256,8 @@ adb_probe_task(void *x) sigprocmask(SIG_BLOCK, &blocked, NULL); flush_signals(current); + down(&adb_probe_mutex); + printk(KERN_INFO "adb: starting probe task...\n"); do_adb_reset_bus(); printk(KERN_INFO "adb: finished probe task...\n"); @@ -282,7 +284,9 @@ adb_reset_bus(void) return 0; } - down(&adb_probe_mutex); + if (adb_got_sleep) + return 0; + schedule_work(&adb_reset_work); return 0; } @@ -345,9 +349,8 @@ adb_notify_sleep(struct pmu_sleep_notifi { switch (when) { case PBOOK_SLEEP_REQUEST: + /* Signal to discontiue probing */ adb_got_sleep = 1; - /* We need to get a lock on the probe thread */ - down(&adb_probe_mutex); /* Stop autopoll */ if (adb_controller->autopoll) adb_controller->autopoll(0); @@ -356,7 +359,6 @@ adb_notify_sleep(struct pmu_sleep_notifi break; case PBOOK_WAKE: adb_got_sleep = 0; - up(&adb_probe_mutex); adb_reset_bus(); break; } Index: linux/drivers/media/dvb/dvb-core/dvb_frontend.c =================================================================== --- linux.orig/drivers/media/dvb/dvb-core/dvb_frontend.c +++ linux/drivers/media/dvb/dvb-core/dvb_frontend.c @@ -98,7 +98,7 @@ struct dvb_frontend_private { struct dvb_device *dvbdev; struct dvb_frontend_parameters parameters; struct dvb_fe_events events; - struct semaphore sem; + struct compat_semaphore sem; struct list_head list_head; wait_queue_head_t wait_queue; struct task_struct *thread; Index: linux/drivers/media/dvb/dvb-core/dvb_frontend.h =================================================================== --- linux.orig/drivers/media/dvb/dvb-core/dvb_frontend.h +++ linux/drivers/media/dvb/dvb-core/dvb_frontend.h @@ -142,7 +142,7 @@ struct dvb_fe_events { int eventr; int overflow; wait_queue_head_t wait_queue; - struct semaphore sem; + struct compat_semaphore sem; }; struct dvb_frontend { Index: linux/drivers/net/3c527.c =================================================================== --- linux.orig/drivers/net/3c527.c +++ linux/drivers/net/3c527.c @@ -182,7 +182,7 @@ struct mc32_local u16 rx_ring_tail; /* index to rx de-queue end */ - struct semaphore cmd_mutex; /* Serialises issuing of execute commands */ + struct compat_semaphore cmd_mutex; /* Serialises issuing of execute commands */ struct completion execution_cmd; /* Card has completed an execute command */ struct completion xceiver_cmd; /* Card has completed a tx or rx command */ }; Index: linux/drivers/net/3c59x.c =================================================================== --- linux.orig/drivers/net/3c59x.c +++ linux/drivers/net/3c59x.c @@ -792,9 +792,9 @@ static void poll_vortex(struct net_devic { struct vortex_private *vp = netdev_priv(dev); unsigned long flags; - local_irq_save(flags); + local_irq_save_nort(flags); (vp->full_bus_master_rx ? boomerang_interrupt:vortex_interrupt)(dev->irq,dev); - local_irq_restore(flags); + local_irq_restore_nort(flags); } #endif @@ -1728,6 +1728,7 @@ vortex_timer(unsigned long data) int next_tick = 60*HZ; int ok = 0; int media_status, old_window; + unsigned long flags; if (vortex_debug > 2) { printk(KERN_DEBUG "%s: Media selection timer tick happened, %s.\n", @@ -1735,7 +1736,7 @@ vortex_timer(unsigned long data) printk(KERN_DEBUG "dev->watchdog_timeo=%d\n", dev->watchdog_timeo); } - disable_irq_lockdep(dev->irq); + spin_lock_irqsave(&vp->lock, flags); old_window = ioread16(ioaddr + EL3_CMD) >> 13; EL3WINDOW(4); media_status = ioread16(ioaddr + Wn4_Media); @@ -1758,9 +1759,7 @@ vortex_timer(unsigned long data) case XCVR_MII: case XCVR_NWAY: { ok = 1; - spin_lock_bh(&vp->lock); vortex_check_media(dev, 0); - spin_unlock_bh(&vp->lock); } break; default: /* Other media types handled by Tx timeouts. */ @@ -1816,7 +1815,7 @@ leave_media_alone: dev->name, media_tbl[dev->if_port].name); EL3WINDOW(old_window); - enable_irq_lockdep(dev->irq); + spin_unlock_irqrestore(&vp->lock, flags); mod_timer(&vp->timer, RUN_AT(next_tick)); if (vp->deferred) iowrite16(FakeIntr, ioaddr + EL3_CMD); @@ -1849,13 +1848,17 @@ static void vortex_tx_timeout(struct net /* * Block interrupts because vortex_interrupt does a bare spin_lock() */ +#ifndef CONFIG_PREEMPT_RT unsigned long flags; local_irq_save(flags); +#endif if (vp->full_bus_master_tx) boomerang_interrupt(dev->irq, dev); else vortex_interrupt(dev->irq, dev); +#ifndef CONFIG_PREEMPT_RT local_irq_restore(flags); +#endif } } Index: linux/drivers/net/8139too.c =================================================================== --- linux.orig/drivers/net/8139too.c +++ linux/drivers/net/8139too.c @@ -2131,10 +2131,10 @@ static int rtl8139_poll(struct net_devic * Order is important since data can get interrupted * again when we think we are done. */ - local_irq_save(flags); + local_irq_save_nort(flags); RTL_W16_F(IntrMask, rtl8139_intr_mask); __netif_rx_complete(dev); - local_irq_restore(flags); + local_irq_restore_nort(flags); } spin_unlock(&tp->rx_lock); @@ -2214,7 +2214,11 @@ static irqreturn_t rtl8139_interrupt (in */ static void rtl8139_poll_controller(struct net_device *dev) { - disable_irq(dev->irq); + /* + * use _nosync() variant - might be used by netconsole + * from atomic contexts: + */ + disable_irq_nosync(dev->irq); rtl8139_interrupt(dev->irq, dev); enable_irq(dev->irq); } Index: linux/drivers/net/hamradio/6pack.c =================================================================== --- linux.orig/drivers/net/hamradio/6pack.c +++ linux/drivers/net/hamradio/6pack.c @@ -123,7 +123,7 @@ struct sixpack { struct timer_list tx_t; struct timer_list resync_t; atomic_t refcnt; - struct semaphore dead_sem; + struct compat_semaphore dead_sem; spinlock_t lock; }; Index: linux/drivers/net/hamradio/mkiss.c =================================================================== --- linux.orig/drivers/net/hamradio/mkiss.c +++ linux/drivers/net/hamradio/mkiss.c @@ -84,7 +84,7 @@ struct mkiss { #define CRC_MODE_SMACK_TEST 4 atomic_t refcnt; - struct semaphore dead_sem; + struct compat_semaphore dead_sem; }; /*---------------------------------------------------------------------------*/ Index: linux/drivers/net/ibm_emac/ibm_emac_core.c =================================================================== --- linux.orig/drivers/net/ibm_emac/ibm_emac_core.c +++ linux/drivers/net/ibm_emac/ibm_emac_core.c @@ -1059,6 +1059,8 @@ static inline int emac_xmit_finish(struc ++dev->stats.tx_packets; dev->stats.tx_bytes += len; + spin_unlock(&dev->tx_lock); + return 0; } @@ -1072,6 +1074,7 @@ static int emac_start_xmit(struct sk_buf u16 ctrl = EMAC_TX_CTRL_GFCS | EMAC_TX_CTRL_GP | MAL_TX_CTRL_READY | MAL_TX_CTRL_LAST | emac_tx_csum(dev, skb); + spin_lock(&dev->tx_lock); slot = dev->tx_slot++; if (dev->tx_slot == NUM_TX_BUFF) { dev->tx_slot = 0; @@ -1134,6 +1137,8 @@ static int emac_start_xmit_sg(struct sk_ if (likely(!nr_frags && len <= MAL_MAX_TX_SIZE)) return emac_start_xmit(skb, ndev); + spin_lock(&dev->tx_lock); + len -= skb->data_len; /* Note, this is only an *estimation*, we can still run out of empty @@ -1202,6 +1207,7 @@ static int emac_start_xmit_sg(struct sk_ stop_queue: netif_stop_queue(ndev); DBG2("%d: stopped TX queue" NL, dev->def->index); + spin_unlock(&dev->tx_lock); return 1; } #else @@ -1241,6 +1247,7 @@ static void emac_poll_tx(void *param) DBG2("%d: poll_tx, %d %d" NL, dev->def->index, dev->tx_cnt, dev->ack_slot); + spin_lock(&dev->tx_lock); if (dev->tx_cnt) { u16 ctrl; int slot = dev->ack_slot, n = 0; @@ -1250,6 +1257,7 @@ static void emac_poll_tx(void *param) struct sk_buff *skb = dev->tx_skb[slot]; ++n; + spin_unlock(&dev->tx_lock); if (skb) { dev_kfree_skb(skb); dev->tx_skb[slot] = NULL; @@ -1259,6 +1267,7 @@ static void emac_poll_tx(void *param) if (unlikely(EMAC_IS_BAD_TX(ctrl))) emac_parse_tx_error(dev, ctrl); + spin_lock(&dev->tx_lock); if (--dev->tx_cnt) goto again; } @@ -1271,6 +1280,7 @@ static void emac_poll_tx(void *param) DBG2("%d: tx %d pkts" NL, dev->def->index, n); } } + spin_unlock(&dev->tx_lock); } static inline void emac_recycle_rx_skb(struct ocp_enet_private *dev, int slot, @@ -1963,6 +1973,7 @@ static int __init emac_probe(struct ocp_ dev->ldev = &ocpdev->dev; dev->def = ocpdev->def; SET_MODULE_OWNER(ndev); + spin_lock_init(&dev->tx_lock); /* Find MAL device we are connected to */ maldev = Index: linux/drivers/net/ibm_emac/ibm_emac_core.h =================================================================== --- linux.orig/drivers/net/ibm_emac/ibm_emac_core.h +++ linux/drivers/net/ibm_emac/ibm_emac_core.h @@ -193,6 +193,8 @@ struct ocp_enet_private { struct ibm_emac_error_stats estats; struct net_device_stats nstats; + spinlock_t tx_lock; + struct device* ldev; }; Index: linux/drivers/net/loopback.c =================================================================== --- linux.orig/drivers/net/loopback.c +++ linux/drivers/net/loopback.c @@ -154,12 +154,12 @@ static int loopback_xmit(struct sk_buff #endif dev->last_rx = jiffies; - /* it's OK to use __get_cpu_var() because BHs are off */ - lb_stats = &__get_cpu_var(pcpu_lstats); + lb_stats = &per_cpu(pcpu_lstats, get_cpu()); lb_stats->bytes += skb->len; lb_stats->packets++; + put_cpu(); - netif_rx(skb); + netif_rx_ni(skb); return 0; } Index: linux/drivers/net/netconsole.c =================================================================== --- linux.orig/drivers/net/netconsole.c +++ linux/drivers/net/netconsole.c @@ -68,21 +68,16 @@ static int configured = 0; static void write_msg(struct console *con, const char *msg, unsigned int len) { int frag, left; - unsigned long flags; if (!np.dev) return; - local_irq_save(flags); - - for(left = len; left; ) { + for (left = len; left; ) { frag = min(left, MAX_PRINT_CHUNK); netpoll_send_udp(&np, msg, frag); msg += frag; left -= frag; } - - local_irq_restore(flags); } static struct console netconsole = { Index: linux/drivers/net/plip.c =================================================================== --- linux.orig/drivers/net/plip.c +++ linux/drivers/net/plip.c @@ -228,7 +228,10 @@ struct net_local { struct hh_cache *hh); spinlock_t lock; atomic_t kill_timer; - struct semaphore killed_timer_sem; + /* + * PREEMPT_RT: this isnt a mutex, it should be struct completion. + */ + struct compat_semaphore killed_timer_sem; }; static inline void enable_parport_interrupts (struct net_device *dev) Index: linux/drivers/net/ppp_async.c =================================================================== --- linux.orig/drivers/net/ppp_async.c +++ linux/drivers/net/ppp_async.c @@ -67,7 +67,7 @@ struct asyncppp { struct tasklet_struct tsk; atomic_t refcnt; - struct semaphore dead_sem; + struct compat_semaphore dead_sem; struct ppp_channel chan; /* interface to generic ppp layer */ unsigned char obuf[OBUFSIZE]; }; Index: linux/drivers/net/ppp_synctty.c =================================================================== --- linux.orig/drivers/net/ppp_synctty.c +++ linux/drivers/net/ppp_synctty.c @@ -70,7 +70,7 @@ struct syncppp { struct tasklet_struct tsk; atomic_t refcnt; - struct semaphore dead_sem; + struct compat_semaphore dead_sem; struct ppp_channel chan; /* interface to generic ppp layer */ }; Index: linux/drivers/net/sungem.c =================================================================== --- linux.orig/drivers/net/sungem.c +++ linux/drivers/net/sungem.c @@ -1034,10 +1034,8 @@ static int gem_start_xmit(struct sk_buff (csum_stuff_off << 21)); } - local_irq_save(flags); - if (!spin_trylock(&gp->tx_lock)) { + if (!spin_trylock_irqsave(&gp->tx_lock, flags)) { /* Tell upper layer to requeue */ - local_irq_restore(flags); return NETDEV_TX_LOCKED; } /* We raced with gem_do_stop() */ Index: linux/drivers/net/tulip/tulip_core.c =================================================================== --- linux.orig/drivers/net/tulip/tulip_core.c +++ linux/drivers/net/tulip/tulip_core.c @@ -1803,6 +1803,7 @@ static void __devexit tulip_remove_one ( pci_iounmap(pdev, tp->base_addr); free_netdev (dev); pci_release_regions (pdev); + pci_disable_device (pdev); pci_set_drvdata (pdev, NULL); /* pci_power_off (pdev, -1); */ Index: linux/drivers/net/usb/usbnet.c =================================================================== --- linux.orig/drivers/net/usb/usbnet.c +++ linux/drivers/net/usb/usbnet.c @@ -896,6 +896,8 @@ static void tx_complete (struct urb *urb urb->dev = NULL; entry->state = tx_done; + spin_lock_rt(&dev->txq.lock); + spin_unlock_rt(&dev->txq.lock); defer_bh(dev, skb, &dev->txq); } Index: linux/drivers/oprofile/oprofilefs.c =================================================================== --- linux.orig/drivers/oprofile/oprofilefs.c +++ linux/drivers/oprofile/oprofilefs.c @@ -21,7 +21,7 @@ #define OPROFILEFS_MAGIC 0x6f70726f -DEFINE_SPINLOCK(oprofilefs_lock); +DEFINE_RAW_SPINLOCK(oprofilefs_lock); static struct inode * oprofilefs_get_inode(struct super_block * sb, int mode) { Index: linux/drivers/pci/access.c =================================================================== --- linux.orig/drivers/pci/access.c +++ linux/drivers/pci/access.c @@ -11,7 +11,7 @@ * configuration space. */ -static DEFINE_SPINLOCK(pci_lock); +static DEFINE_RAW_SPINLOCK(pci_lock); /* * Wrappers for all PCI configuration access functions. They just check Index: linux/drivers/pci/hotplug/cpci_hotplug_core.c =================================================================== --- linux.orig/drivers/pci/hotplug/cpci_hotplug_core.c +++ linux/drivers/pci/hotplug/cpci_hotplug_core.c @@ -59,8 +59,8 @@ static int slots; static atomic_t extracting; int cpci_debug; static struct cpci_hp_controller *controller; -static struct semaphore event_semaphore; /* mutex for process loop (up if something to process) */ -static struct semaphore thread_exit; /* guard ensure thread has exited before calling it quits */ +static struct compat_semaphore event_semaphore; /* mutex for process loop (up if something to process) */ +static struct compat_semaphore thread_exit; /* guard ensure thread has exited before calling it quits */ static int thread_finished = 1; static int enable_slot(struct hotplug_slot *slot); @@ -521,9 +521,9 @@ event_thread(void *data) { int rc; - lock_kernel(); +// lock_kernel(); daemonize("cpci_hp_eventd"); - unlock_kernel(); +// unlock_kernel(); dbg("%s - event thread started", __FUNCTION__); while (1) { @@ -562,9 +562,9 @@ poll_thread(void *data) { int rc; - lock_kernel(); +// lock_kernel(); daemonize("cpci_hp_polld"); - unlock_kernel(); +// unlock_kernel(); while (1) { if (thread_finished || signal_pending(current)) Index: linux/drivers/pci/hotplug/cpqphp_ctrl.c =================================================================== --- linux.orig/drivers/pci/hotplug/cpqphp_ctrl.c +++ linux/drivers/pci/hotplug/cpqphp_ctrl.c @@ -45,8 +45,8 @@ static int configure_new_function(struct u8 behind_bridge, struct resource_lists *resources); static void interrupt_event_handler(struct controller *ctrl); -static struct semaphore event_semaphore; /* mutex for process loop (up if something to process) */ -static struct semaphore event_exit; /* guard ensure thread has exited before calling it quits */ +static struct compat_semaphore event_semaphore; /* mutex for process loop (up if something to process) */ +static struct compat_semaphore event_exit; /* guard ensure thread has exited before calling it quits */ static int event_finished; static unsigned long pushbutton_pending; /* = 0 */ @@ -1746,10 +1746,10 @@ static void pushbutton_helper_thread(uns static int event_thread(void* data) { struct controller *ctrl; - lock_kernel(); +// lock_kernel(); daemonize("phpd_event"); - unlock_kernel(); +// unlock_kernel(); while (1) { dbg("!!!!event_thread sleeping\n"); Index: linux/drivers/pci/hotplug/ibmphp_hpc.c =================================================================== --- linux.orig/drivers/pci/hotplug/ibmphp_hpc.c +++ linux/drivers/pci/hotplug/ibmphp_hpc.c @@ -106,7 +106,7 @@ static int tid_poll; static struct mutex sem_hpcaccess; // lock access to HPC static struct semaphore semOperations; // lock all operations and // access to data structures -static struct semaphore sem_exit; // make sure polling thread goes away +static struct compat_semaphore sem_exit; // make sure polling thread goes away //---------------------------------------------------------------------------- // local function prototypes //---------------------------------------------------------------------------- Index: linux/drivers/pci/msi.c =================================================================== --- linux.orig/drivers/pci/msi.c +++ linux/drivers/pci/msi.c @@ -235,6 +235,10 @@ static void __pci_restore_msi_state(stru return; entry = get_irq_msi(dev->irq); + if (!entry) { + WARN_ON(1); + return; + } pos = entry->msi_attrib.pos; pci_intx(dev, 0); /* disable intx */ Index: linux/drivers/pci/pcie/aer/aerdrv.c =================================================================== --- linux.orig/drivers/pci/pcie/aer/aerdrv.c +++ linux/drivers/pci/pcie/aer/aerdrv.c @@ -157,7 +157,7 @@ static struct aer_rpc* aer_alloc_rpc(str * Initialize Root lock access, e_lock, to Root Error Status Reg, * Root Error ID Reg, and Root error producer/consumer index. */ - rpc->e_lock = SPIN_LOCK_UNLOCKED; + spin_lock_init(&rpc->e_lock); rpc->rpd = dev; INIT_WORK(&rpc->dpc_handler, aer_isr); Index: linux/drivers/scsi/aacraid/aacraid.h =================================================================== --- linux.orig/drivers/scsi/aacraid/aacraid.h +++ linux/drivers/scsi/aacraid/aacraid.h @@ -715,7 +715,7 @@ struct aac_fib_context { u32 unique; // unique value representing this context ulong jiffies; // used for cleanup - dmb changed to ulong struct list_head next; // used to link context's into a linked list - struct semaphore wait_sem; // this is used to wait for the next fib to arrive. + struct compat_semaphore wait_sem; // this is used to wait for the next fib to arrive. int wait; // Set to true when thread is in WaitForSingleObject unsigned long count; // total number of FIBs on FibList struct list_head fib_list; // this holds fibs and their attachd hw_fibs @@ -785,7 +785,7 @@ struct fib { * This is the event the sendfib routine will wait on if the * caller did not pass one and this is synch io. */ - struct semaphore event_wait; + struct compat_semaphore event_wait; spinlock_t event_lock; u32 done; /* gets set to 1 when fib is complete */ Index: linux/drivers/scsi/qla2xxx/qla_def.h =================================================================== --- linux.orig/drivers/scsi/qla2xxx/qla_def.h +++ linux/drivers/scsi/qla2xxx/qla_def.h @@ -2344,7 +2344,7 @@ typedef struct scsi_qla_host { #define MBX_UPDATE_FLASH_ACTIVE 3 struct semaphore mbx_cmd_sem; /* Serialialize mbx access */ - struct semaphore mbx_intr_sem; /* Used for completion notification */ + struct compat_semaphore mbx_intr_sem; /* Used for completion notification */ uint32_t mbx_flags; #define MBX_IN_PROGRESS BIT_0 Index: linux/drivers/serial/8250.c =================================================================== --- linux.orig/drivers/serial/8250.c +++ linux/drivers/serial/8250.c @@ -1451,7 +1451,10 @@ static irqreturn_t serial8250_interrupt( { struct irq_info *i = dev_id; struct list_head *l, *end = NULL; - int pass_counter = 0, handled = 0; +#ifndef CONFIG_PREEMPT_RT + int pass_counter = 0; +#endif + int handled = 0; DEBUG_INTR("serial8250_interrupt(%d)...", irq); @@ -1489,12 +1492,18 @@ static irqreturn_t serial8250_interrupt( l = l->next; + /* + * On preempt-rt we can be preempted and run in our + * own thread. + */ +#ifndef CONFIG_PREEMPT_RT if (l == i->head && pass_counter++ > PASS_LIMIT) { /* If we hit this, we're dead. */ printk(KERN_ERR "serial8250: too much work for " "irq%d\n", irq); break; } +#endif } while (l != end); spin_unlock(&i->lock); @@ -2456,14 +2465,10 @@ serial8250_console_write(struct console touch_nmi_watchdog(); - local_irq_save(flags); - if (up->port.sysrq) { - /* serial8250_handle_port() already took the lock */ - locked = 0; - } else if (oops_in_progress) { - locked = spin_trylock(&up->port.lock); - } else - spin_lock(&up->port.lock); + if (up->port.sysrq || oops_in_progress) + locked = spin_trylock_irqsave(&up->port.lock, flags); + else + spin_lock_irqsave(&up->port.lock, flags); /* * First save the IER then disable the interrupts @@ -2485,8 +2490,7 @@ serial8250_console_write(struct console serial_out(up, UART_IER, ier); if (locked) - spin_unlock(&up->port.lock); - local_irq_restore(flags); + spin_unlock_irqrestore(&up->port.lock, flags); } static int __init serial8250_console_setup(struct console *co, char *options) Index: linux/drivers/usb/core/devio.c =================================================================== --- linux.orig/drivers/usb/core/devio.c +++ linux/drivers/usb/core/devio.c @@ -308,10 +308,11 @@ static void async_completed(struct urb * struct async *as = urb->context; struct dev_state *ps = as->ps; struct siginfo sinfo; + unsigned long flags; - spin_lock(&ps->lock); - list_move_tail(&as->asynclist, &ps->async_completed); - spin_unlock(&ps->lock); + spin_lock_irqsave(&ps->lock, flags); + list_move_tail(&as->asynclist, &ps->async_completed); + spin_unlock_irqrestore(&ps->lock, flags); if (as->signr) { sinfo.si_signo = as->signr; sinfo.si_errno = as->urb->status; Index: linux/drivers/usb/core/hcd.c =================================================================== --- linux.orig/drivers/usb/core/hcd.c +++ linux/drivers/usb/core/hcd.c @@ -518,13 +518,11 @@ error: } /* any errors get returned through the urb completion */ - local_irq_save (flags); - spin_lock (&urb->lock); + spin_lock_irqsave(&urb->lock, flags); if (urb->status == -EINPROGRESS) urb->status = status; - spin_unlock (&urb->lock); + spin_unlock_irqrestore(&urb->lock, flags); usb_hcd_giveback_urb (hcd, urb); - local_irq_restore (flags); return 0; } @@ -554,8 +552,7 @@ void usb_hcd_poll_rh_status(struct usb_h if (length > 0) { /* try to complete the status urb */ - local_irq_save (flags); - spin_lock(&hcd_root_hub_lock); + spin_lock_irqsave(&hcd_root_hub_lock, flags); urb = hcd->status_urb; if (urb) { spin_lock(&urb->lock); @@ -571,14 +568,13 @@ void usb_hcd_poll_rh_status(struct usb_h spin_unlock(&urb->lock); } else length = 0; - spin_unlock(&hcd_root_hub_lock); + spin_unlock_irqrestore(&hcd_root_hub_lock, flags); /* local irqs are always blocked in completions */ if (length > 0) usb_hcd_giveback_urb (hcd, urb); else hcd->poll_pending = 1; - local_irq_restore (flags); } /* The USB 2.0 spec says 256 ms. This is close enough and won't @@ -650,17 +646,15 @@ static int usb_rh_urb_dequeue (struct us } else { /* Status URB */ if (!hcd->uses_new_polling) del_timer (&hcd->rh_timer); - local_irq_save (flags); - spin_lock (&hcd_root_hub_lock); + spin_lock_irqsave(&hcd_root_hub_lock, flags); if (urb == hcd->status_urb) { hcd->status_urb = NULL; urb->hcpriv = NULL; } else urb = NULL; /* wasn't fully queued */ - spin_unlock (&hcd_root_hub_lock); + spin_unlock_irqrestore(&hcd_root_hub_lock, flags); if (urb) usb_hcd_giveback_urb (hcd, urb); - local_irq_restore (flags); } return 0; @@ -1175,11 +1169,10 @@ void usb_hcd_endpoint_disable (struct us struct urb *urb; hcd = bus_to_hcd(udev->bus); - local_irq_disable (); /* ep is already gone from udev->ep_{in,out}[]; no more submits */ rescan: - spin_lock (&hcd_data_lock); + spin_lock_irq(&hcd_data_lock); list_for_each_entry (urb, &ep->urb_list, urb_list) { int tmp; @@ -1187,13 +1180,13 @@ rescan: if (urb->status != -EINPROGRESS) continue; usb_get_urb (urb); - spin_unlock (&hcd_data_lock); + spin_unlock_irq(&hcd_data_lock); - spin_lock (&urb->lock); + spin_lock_irq(&urb->lock); tmp = urb->status; if (tmp == -EINPROGRESS) urb->status = -ESHUTDOWN; - spin_unlock (&urb->lock); + spin_unlock_irq(&urb->lock); /* kick hcd unless it's already returning this */ if (tmp == -EINPROGRESS) { @@ -1216,8 +1209,7 @@ rescan: /* list contents may have changed */ goto rescan; } - spin_unlock (&hcd_data_lock); - local_irq_enable (); + spin_unlock_irq(&hcd_data_lock); /* synchronize with the hardware, so old configuration state * clears out immediately (and will be freed). Index: linux/drivers/usb/core/message.c =================================================================== --- linux.orig/drivers/usb/core/message.c +++ linux/drivers/usb/core/message.c @@ -250,8 +250,9 @@ static void sg_clean (struct usb_sg_requ static void sg_complete (struct urb *urb) { struct usb_sg_request *io = urb->context; + unsigned long flags; - spin_lock (&io->lock); + spin_lock_irqsave (&io->lock, flags); /* In 2.5 we require hcds' endpoint queues not to progress after fault * reports, until the completion callback (this!) returns. That lets @@ -285,7 +286,7 @@ static void sg_complete (struct urb *urb * unlink pending urbs so they won't rx/tx bad data. * careful: unlink can sometimes be synchronous... */ - spin_unlock (&io->lock); + spin_unlock_irqrestore (&io->lock, flags); for (i = 0, found = 0; i < io->entries; i++) { if (!io->urbs [i] || !io->urbs [i]->dev) continue; @@ -300,7 +301,7 @@ static void sg_complete (struct urb *urb } else if (urb == io->urbs [i]) found = 1; } - spin_lock (&io->lock); + spin_lock_irqsave (&io->lock, flags); } urb->dev = NULL; @@ -310,7 +311,7 @@ static void sg_complete (struct urb *urb if (!io->count) complete (&io->complete); - spin_unlock (&io->lock); + spin_unlock_irqrestore (&io->lock, flags); } @@ -586,7 +587,7 @@ void usb_sg_cancel (struct usb_sg_reques dev_warn (&io->dev->dev, "%s, unlink --> %d\n", __FUNCTION__, retval); } - spin_lock (&io->lock); + spin_lock_irqsave (&io->lock, flags); } spin_unlock_irqrestore (&io->lock, flags); } Index: linux/drivers/usb/storage/usb.h =================================================================== --- linux.orig/drivers/usb/storage/usb.h +++ linux/drivers/usb/storage/usb.h @@ -146,7 +146,7 @@ struct us_data { dma_addr_t iobuf_dma; /* mutual exclusion and synchronization structures */ - struct semaphore sema; /* to sleep thread on */ + struct compat_semaphore sema; /* to sleep thread on */ struct completion notify; /* thread begin/end */ wait_queue_head_t delay_wait; /* wait during scan, reset */ Index: linux/drivers/video/console/fbcon.c =================================================================== --- linux.orig/drivers/video/console/fbcon.c +++ linux/drivers/video/console/fbcon.c @@ -1287,7 +1287,6 @@ static void fbcon_clear(struct vc_data * { struct fb_info *info = registered_fb[con2fb_map[vc->vc_num]]; struct fbcon_ops *ops = info->fbcon_par; - struct display *p = &fb_display[vc->vc_num]; u_int y_break; @@ -1316,10 +1315,11 @@ static void fbcon_putcs(struct vc_data * struct display *p = &fb_display[vc->vc_num]; struct fbcon_ops *ops = info->fbcon_par; - if (!fbcon_is_inactive(vc, info)) + if (!fbcon_is_inactive(vc, info)) { ops->putcs(vc, info, s, count, real_y(p, ypos), xpos, get_color(vc, info, scr_readw(s), 1), get_color(vc, info, scr_readw(s), 0)); + } } static void fbcon_putc(struct vc_data *vc, int c, int ypos, int xpos) @@ -3173,6 +3173,7 @@ static const struct consw fb_con = { .con_screen_pos = fbcon_screen_pos, .con_getxy = fbcon_getxy, .con_resize = fbcon_resize, + .con_preemptible = 1, }; static struct notifier_block fbcon_event_notifier = { Index: linux/drivers/video/console/vgacon.c =================================================================== --- linux.orig/drivers/video/console/vgacon.c +++ linux/drivers/video/console/vgacon.c @@ -51,7 +51,7 @@ #include